As we fallback to use "mediatek,mt7623" for MT7623a, remove unused
root node property "mediatek,mt7623a" in the document.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add documentation about how to probe the jz4725b-codec driver from
devicetree.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add documentation about how to probe the jz4740-codec driver from
devicetree.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Lochnagar is an evaluation and development board for Cirrus
Logic Smart CODEC and Amp devices. It allows the connection of
most Cirrus Logic devices on mini-cards, as well as allowing
connection of various application processor systems to provide a
full evaluation platform. This driver supports the board
controller chip on the Lochnagar board.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Memory-region and flash phandle is not a required parameter, it is
optional to describe in device tree and needed only use basis.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add DT binding document for the Ilitek ILI210x and ILI251x
touchscreen controllers.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Cadence D-PHY bindings was defined as part of the DSI block so far.
However, since it's now going to be a separate driver, we need to move the
binding to a file of its own.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Current file describe COMPHY bindings for the IP available on the
CP110 of Armada 7k/8k. Bindings are very close (and serve the same
purpose) as the new Armada 3700 COMPHY driver so update this file to
describe both. Also add an example of how to use this second
compatible (same as for the ESPRESSObin).
While doing so, enhance a bit the file by adding upper case where
needed.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Commit 98898f3bc8 ("phy: rockchip-inno-usb2: support otg-port for
rk3399") introduces the extcon property that is used to detect the
cable-state. Document this property in the documentation binding.
Fixes: 98898f3bc8 ("phy: rockchip-inno-usb2: support otg-port for rk3399")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for USB2 PHY on AM654x SoC.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-02-07
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add a riscv64 JIT for BPF, from Björn.
2) Implement BTF deduplication algorithm for libbpf which takes BTF type
information containing duplicate per-compilation unit information and
reduces it to an equivalent set of BTF types with no duplication and
without loss of information, from Andrii.
3) Offloaded and native BPF XDP programs can coexist today, enable also
offloaded and generic ones as well, from Jakub.
4) Expose various BTF related helper functions in libbpf as API which
are in particular helpful for JITed programs, from Yonghong.
5) Fix the recently added JMP32 code emission in s390x JIT, from Heiko.
6) Fix BPF kselftests' tcp_{server,client}.py to be able to run inside
a network namespace, also add a fix for libbpf to get libbpf_print()
working, from Stanislav.
7) Fixes for bpftool documentation, from Prashant.
8) Type cleanup in BPF kselftests' test_maps.c to silence a gcc8 warning,
from Breno.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For a while Arm64 has been capable of force enabling
or disabling the kpti mitigations. Lets make sure the
documentation reflects that.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This patch adds the Italian translation for the following documents
in Documentation/process:
- applying-patches
- submit-checklist
- submitting-drivers
- changes
- stable api nonsense
Signed-off-by: Federico Vaga <federico.vaga@vaga.pv.it>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This patch translates in Italian the content of the following patch
7967656ffb coding-style: Clarify the expectations around bool
Signed-off-by: Federico Vaga <federico.vaga@vaga.pv.it>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Legacy IO schedulers (cfq, deadline and noop) were removed in
f382fb0bce.
The documentation for deadline was retained because it carries over to
mq-deadline as well, but location of the doc file was changed over time.
The old iosched algorithms were removed from elevator= kernel parameter
and mq-deadline, kyber and bfq were added with a reference to their
documentation.
Fixes: f382fb0bce ("block: remove legacy IO schedulers")
Signed-off-by: Otto Sabart <ottosabart@seberm.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Fix the spelling of 'functionnality' -> 'functionality'.
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Clkdev registration lacks of managed registration functions and it
seems few drivers do not drop clkdev lookups at exit. Add
devm_clk_hw_register_clkdev and devm_clk_release_clkdev to ease lookup
releasing at exit.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds clk_get_optional() and devm_clk_get_optional() functions to get
optional clocks.
They behave the same as (devm_)clk_get() except where there is no clock
producer. In this case, instead of returning -ENOENT, the function
returns NULL. This makes error checking simpler and allows
clk_prepare_enable, etc to be called on the returned reference
without additional checks.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Russell King <linux@armlinux.org.uk>
[sboyd@kernel.org: Document in devres.txt]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This differs slightly from the IDR equivalent in five ways.
1. It can allocate up to UINT_MAX instead of being limited to INT_MAX,
like xa_alloc(). Also like xa_alloc(), it will write to the 'id'
pointer before placing the entry in the XArray.
2. The 'next' cursor is allocated separately from the XArray instead
of being part of the IDR. This saves memory for all the users which
do not use the cyclic allocation API and suits some users better.
3. It returns -EBUSY instead of -ENOSPC.
4. It will attempt to wrap back to the minimum value on memory allocation
failure as well as on an -EBUSY error, assuming that a user would
rather allocate a small ID than suffer an ID allocation failure.
5. It reports whether it has wrapped, which is important to some users.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
A lot of places want to allocate IDs starting at 1 instead of 0.
While the xa_alloc() API supports this, it's not very efficient if lots
of IDs are allocated, due to having to walk down to the bottom of the
tree to see if ID 1 is available, then all the way over to the next
non-allocated ID. This method marks ID 0 as being occupied which wastes
one slot in the XArray, but preserves xa_empty() as working.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Userspace translates EEXIST to "File exists" which isn't a very good
error message for the problem. "Device or resource busy" is a better
indication of what went wrong.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
This patch adds a new vibrator driver that supports various Qualcomm
MSM SOCs. Driver was tested on a LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The sam9x60 qspi controller uses 2 clocks, one for the peripheral register
access, the other for the qspi core and phy. Both are mandatory.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Naming clocks is a good practice. Make "pclk" madatory even if
we support unnamed clock in the driver, to be backward compatible
with old DTs.
Suggested-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The cpu_lp clock property is only needed when the CPUfreq driver
supports CPU cluster switching. But it was not a design for this driver
and it didn't handle that as well. So removing this property.
Cc: devicetree@vger.kernel.org
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra124 cpufreq driver works only with DFLL clock, which is a
hardware-based frequency/voltage controller. The driver doesn't need to
control the regulator itself. Hence remove that.
Cc: devicetree@vger.kernel.org
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The values non secure EL1 needs to use for PMR and RPR registers depends on
the value of SCR_EL3.FIQ.
The values non secure EL1 sees from the distributor and redistributor
depend on whether security is enabled for the GIC or not.
To avoid having to deal with two sets of values for PMR
masking/unmasking, only enable pseudo-NMIs when GIC has non-secure view
of priorities.
Also, add firmware requirements related to SCR_EL3.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Now that all the users are gone the SCSI OSD library can be removed as
well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This was an example for using the SCSI OSD protocol, which we're trying
to remove.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The documentation of Intel drivers is missing the heading adornment for
document titles.
This causes the generated html to have TOC entries from these documents to
appear as top level TOC entries:
* Linux* Base Driver for Intel(R) Ethernet Network Connection
* Contents
* Identifying Your Adapter
* Command Line Parameters
* AutoNeg
* Duplex
...
Add overline heading adornment to document titles.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update device-tree binding with fixed-link support.
With fixed-link support the formerly required property 'phy-handle'
is now optional if 'fixed-link' child is present.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make MDIO child optional and only instantiate the
MDIO bus if the child is actually present.
There are currently no (in-tree) users of this
binding; all (out-of-tree) users use overlays that
get shipped together with the FPGA images that contain
the IP.
This will significantly increase maintainabilty
of future revisions of this IP.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update Documentation/networking/filter.txt and
Documentation/sysctl/net.txt to mention RISC-V.
Signed-off-by: Björn Töpel <bjorn.topel@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
We don't use SPHINX currently in I2C documentation; but preparing the
I2C fault injector docs already is a good idea since it makes it easier
to read. Especially as new stuff is going to be added soon.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
