Add ROHM BD71837 / BD71847 specific device tree bindings for
controlling the PMIC shutdown/reset states and voltages for
different HW states. The PMIC was designed to be used with NXP
i.MX8 SoC and it supports SNVS low power state which seems to
be typical for NXP i.MX SoCs. However, when SNVS is used we must
not allow SW to control enabling/disabling those regulators which
are crucial for system to boot as there is a HW limitation which
causes SW controlled regulators to be kept shut down after SNVS
reset.
Allow setting the SNVS to be used as reset target state and allow
marking those regulators which are critical for boot.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Tested-by: Angus Ainslie <angus@akkea.ca>
Reviewed-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Mark Brown <broonie@kernel.org>
Asynchronous driver probing can help much on kernel fastboot, and
this option can provide a flexible way to optimize and quickly verify
async driver probe.
Also it will help in below cases:
* Some driver actually covers several families of HWs, some of which
could use async probing while others don't. So we can't simply
turn on the PROBE_PREFER_ASYNCHRONOUS flag in driver, but use this
cmdline option, like igb driver async patch discussed at
https://www.spinics.net/lists/netdev/msg545986.html
* For SOC (System on Chip) with multiple spi or i2c controllers, most
of the slave spi/i2c devices will be assigned with fixed controller
number, while async probing may make those controllers get different
index for each boot, which prevents those controller drivers to be
async probed. For platforms not using these spi/i2c slave devices,
they can use this cmdline option to benefit from the async probing.
Suggested-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the at24 driver only creates additional i2c dummies for
atmel,24c00 and it's hard-coded. Some other chips (like for example
Microchip's 24AA02T) also take more slave addresses despite being
otherwise compatible with already supported variants.
Add a new property to the device tree binding document that defines
the total number of i2c slave addresses taken by the device. The
addresses are counted starting from the one in the reg property.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
AM654 SoC has Cadence Octal SPI controller, which is similar to Cadence
QSPI controller but supports Octal IO(x8 data lines) and Double Data
Rate(DDR) mode. Add new compatible to support OSPI controller on TI's
AM654 SoCs.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
This commit extends the flags that can be used in GPIO specifiers to
indicate if a pull-up resistor or pull-down resistor should be
enabled.
While some pinctrl DT bindings already offer the capability of
configuring pull-up/pull-down resistors at the pin level, a number of
simple GPIO controllers don't have any pinmuxing capability, and
therefore do not rely on the pinctrl DT bindings.
Such simple GPIO controllers however sometimes allow to configure
pull-up and pull-down resistors on a per-pin basis, and whether such
resistors should be enabled or not is a highly board-specific HW
characteristic.
By using two additional bits of the GPIO flag specifier, we can easily
allow the Device Tree to describe which GPIOs should have their
pull-up or pull-down resistors enabled. Even though the two options
are mutually exclusive, we still need two bits to encode at least
three states: no pull-up/pull-down, pull-up, pull-down.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull the latest RCU tree from Paul E. McKenney:
- Additional cleanups after RCU flavor consolidation
- Grace-period forward-progress cleanups and improvements
- Documentation updates
- Miscellaneous fixes
- spin_is_locked() conversions to lockdep
- SPDX changes to RCU source and header files
- SRCU updates
- Torture-test updates, including nolibc updates and moving
nolibc to tools/include
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Jonathan writes:
Second set of new device support, features and cleanup for IIO in the 5.1 cycle.
There are a few late breaking fixes in here that weren't worth trying to
rush into 5.0 as they have been with us for quite a while.
New device support
* ad7476
- add support for TI ADS786X parts that are compatible with this Analog
Devices driver. Good to see some simple devices are so similar.
* Ingenic jz47xx SoC ADCs
- new driver and bindings
* Plantower PMS7003 partical sensor
- new driver and bindings including vendor prefix.
* TI DAC7612
- new driver and bindings for this dual DAC.
New features
* ad7768-1
- Sampling frequency control
* bmi160
- Data ready trigger support, including open-drain dt binding.
Cleanup / minor fixes.
* Analog Device DACs
- Fix some inconsistent licenses. These are only ones where there were
two different license marked in the same file, and hence were previously
unclear.
* ads124s08
- Spelling fix.
* adxl345
- Parameter alignement tidy up.
* bmi160
- SPDX
- correct a note on the types of supported interrupts which was too strict.
- use iio_pollfunc_store_time to grab an earlier timestamp.
- use if (ret) instead of if (ret < 0) to be consistent whilst simplifying
some handling where ret was effectively getting written to 0 even though
it was always already 0.
* exynos_adc
- Fix a null pointer dereference on unbind.
- Fix number of channels on Exynos4x12 devices to be 4 rather than 8.
* lpc32xx-adc
- Move DT bindings doc out of staging. Oops, I missed this one when
moving the driver.
- SPDX.
* npcm-adc
- drop documentation of reset node as going to be done differently.
It's a new driver this cycle so no need to support the previous
binding going forwards.
* sps30
- Fix an issue with a loop timeout test that meant it would never identify
a timeout.
- Mark deliberate switch fall throughs.
* tag 'iio-for-5.1b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (26 commits)
iio: adc: exynos-adc: Use proper number of channels for Exynos4x12
dt-binding: iio: remove rst node from NPCM ADC document
dt-bindings: iio: chemical: pms7003: add device tree support
dt-bindings: add Plantower to the vendor prefixes
iio: chemical: add support for Plantower PMS7003 sensor
iio:chemical:sps30 Supress some switch fallthrough warnings.
iio:adc:lpc32xx use SPDX-License-Identifier
dt-bindings: iio: adc: move lpc32xx-adc out of staging
iio: adc: ads124s08: fix spelling mistake "converions" -> "conversions"
iio: adc: exynos-adc: Fix NULL pointer exception on unbind
iio: chemical: sps30: fix a loop timeout test
iio:accel:adxl345: Change alignment to match paranthesis
iio:dac:dac7612: device tree bindings
iio:dac:ti-dac7612: Add driver for Texas Instruments DAC7612
iio: adc: ad7476: Add support for TI ADS786X ADCs
iio: adc: ad7768-1: Add support for setting the sampling frequency
drivers: iio: dac: Fix wrong license for ADI drivers
IIO: add Ingenic JZ47xx ADC driver.
dt-bindings: iio/adc: Add bindings for Ingenic JZ47xx SoCs ADC.
dt-bindings: iio/adc: Add docs for Ingenic JZ47xx SoCs ADC.
...
Exynos4212 and Exynos4412 have only four ADC channels so using
"samsung,exynos-adc-v1" compatible (for eight channels ADCv1) on them is
wrong. Add a new compatible for Exynos4x12.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is a separate PHY device with its own registers on imx7d. It's
currently unused, but a PCIe erratum on imx7d will require it for the
workaround.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Specify "little-endian" property if the 1588 timer IP block
is little-endian mode. The default endian mode is big-endian.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an entry for the "fsl,imx8mq-ecspi" compatible to describe
the ECSPI version present on i.MX8M.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While building arm32 allyesconfig, I ran into the following errors:
arch/arm/lib/xor-neon.c:17:2: error: You should compile this file with
'-mfloat-abi=softfp -mfpu=neon'
In file included from lib/raid6/neon1.c:27:
/home/nathan/cbl/prebuilt/lib/clang/8.0.0/include/arm_neon.h:28:2:
error: "NEON support not enabled"
Building V=1 showed NEON_FLAGS getting passed along to Clang but
__ARM_NEON__ was not getting defined. Ultimately, it boils down to Clang
only defining __ARM_NEON__ when targeting armv7, rather than armv6k,
which is the '-march' value for allyesconfig.
>From lib/Basic/Targets/ARM.cpp in the Clang source:
// This only gets set when Neon instructions are actually available, unlike
// the VFP define, hence the soft float and arch check. This is subtly
// different from gcc, we follow the intent which was that it should be set
// when Neon instructions are actually available.
if ((FPU & NeonFPU) && !SoftFloat && ArchVersion >= 7) {
Builder.defineMacro("__ARM_NEON", "1");
Builder.defineMacro("__ARM_NEON__");
// current AArch32 NEON implementations do not support double-precision
// floating-point even when it is present in VFP.
Builder.defineMacro("__ARM_NEON_FP",
"0x" + Twine::utohexstr(HW_FP & ~HW_FP_DP));
}
Ard Biesheuvel recommended explicitly adding '-march=armv7-a' at the
beginning of the NEON_FLAGS definitions so that __ARM_NEON__ always gets
definined by Clang. This doesn't functionally change anything because
that code will only run where NEON is supported, which is implicitly
armv7.
Link: https://github.com/ClangBuiltLinux/linux/issues/287
Suggested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Kishon writes:
phy: for 5.1
*) Add a new driver to support Armada 3700 COMPHY IP (supports SATA, USB3,
PCIe)
*) Add a new driver to support Armada UTMI PHY
*) Add a new driver to support Cadence D-PHY
*) Extend omap-usb2 PHY driver to be used for AM654 USB2 PHY
*) Extend qcom-qmp PHY driver to be used for UFS PHY and USB3 PHY in Qualcomm
MSM8998
*) Extend qcom-qusb2 PHY driver to support QUSB2 PHY in Qualcomm MSM8998
*) Remove module specific code that is present for drivers that can be only
built-in
*) Allow Freescale IMX8MQ USB to be used for multiple SoCs and not just
i.MX8MQ
*) Cleanups such as switch to SPDX identifier, use readl_poll_timeout macro,
remove unused headers etc.,
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: (32 commits)
phy: qcom-qmp: Add QMP UFS PHY support for msm8998
dt-bindings: phy-qcom-qmp: Add qcom,msm8998-qmp-ufs-phy
phy: bcm-sr-pcie: Change operation when PIPEMUX=1
phy: Add Cadence D-PHY support
dt-bindings: phy: Move the Cadence D-PHY bindings
phy: dphy: Clarify lanes parameter documentation
phy: dphy: Change units of wakeup and init parameters
phy: dphy: Remove unused header
MAINTAINERS: phy: fill Armada 3700 PHY drivers entry
dt-bindings: phy: mvebu-utmi: add UTMI PHY bindings
phy: add A3700 UTMI PHY driver
MAINTAINERS: phy: add entry for Armada 3700 COMPHY driver
dt-bindings: phy: mvebu-comphy: extend the file to describe a3700 bindings
phy: add A3700 COMPHY support
phy: mvebu-cp110-comphy: fix port check in ->xlate()
phy: armada375-usb2: switch to SPDX license identifier
phy: make phy-armada375-usb2 explicitly non-modular
phy: make phy-mvebu-sata explicitly non-modular
phy: make phy-core explicitly non-modular
phy: qcom-qusb2: Add QUSB2 PHY support for msm8998
...
The FastRPC driver implements an IPC (Inter-Processor Communication)
mechanism that allows for clients to transparently make remote method
invocations across DSP and APPS boundaries. This enables developers
to offload tasks to the DSP and free up the application processor for
other tasks.
Co-developed-by: Thierry Escande <thierry.escande@linaro.org>
Signed-off-by: Thierry Escande <thierry.escande@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds documentation for the device-tree bindings of the
jz4740-musb driver, which provides support for the USB gadget mode
of the JZ4740 and similar SoCs from Ingenic.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add compatible string for QMP UFS phy on msm8998.
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Fix markup warnings for one list by using correct list syntax.
Fix markup warnings for another list by using blank lines before the
list.
Documentation/networking/device_drivers/freescale/dpaa2/dpio-driver.rst:30: WARNING: Unexpected indentation.
Documentation/networking/device_drivers/freescale/dpaa2/dpio-driver.rst:143: WARNING: Unexpected indentation.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Stuart Yoder <stuyoder@gmail.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Cc: netdev@vger.kernel.org
Cc: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we have a few PTAGs in place allowing us to transform a filesystem
error in a BUG() call. However, we don't have a panic tag for corrupt
metadata, so introduce XFS_PTAG_VERIFIER_ERROR so that the administrator can
use the fs.xfs.panic_mask sysctl knob to convert any error detected by buffer
verifiers into a kernel panic.
Signed-off-by: Marco Benatto <mbenatto@redhat.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
[darrick: light editing of commit message]
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Netlink has moved from bitmasks to group numbers long ago.
Signed-off-by: Jouke Witteveen <j.witteveen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device tree support for Plantower PMS7003 particulate matter sensor.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Daniel writes:
typed componented support + i915/snd-hda changes
This is needed by the new MEI-HDCP support in i915, so will need to go
in through drm and drivers-misc trees at least.
* tag 'topic/component-typed-2019-02-11' of git://anongit.freedesktop.org/drm/drm-intel:
i915/snd_hdac: I915 subcomponent for the snd_hdac
components: multiple components for a device
component: Add documentation
Fix a grammatical error in the dentry-state text and clarify the usage
of negative dentries.
Fixes: af0c9af1b3 ("fs/dcache: Track & report number of negative dentries")
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It clarifies that the DMA description pointer returned by
`dmaengine_prep_*` function should not be used after submission.
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
AFAIK we never had a isa_virt_to_phys, it always was
isa_virt_to_bus.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The original MODULE_LICENSE string for kernel modules licensed under the
GPL v2 (only / or later) was simply "GPL", which was - and still is -
completely sufficient for the purpose of module loading and checking
whether the module is free software or proprietary.
In January 2003 this was changed with commit 3344ea3ad4b7 ("[PATCH]
MODULE_LICENSE and EXPORT_SYMBOL_GPL support"). This commit can be found in
the history git repository which holds the 1:1 import of Linus' bitkeeper
repository:
https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git/commit/?id=3344ea3ad4b7c302c846a680dbaeedf96ed45c02
The main intention of the patch was to refuse linking proprietary modules
against symbols exported with EXPORT_SYMBOL_GPL() at module load time.
As a completely undocumented side effect it also introduced the distinction
between "GPL" and "GPL v2" MODULE_LICENSE() strings:
* "GPL" [GNU Public License v2 or later]
* "GPL v2" [GNU Public License v2]
* "GPL and additional rights" [GNU Public License v2 rights and more]
* "Dual BSD/GPL" [GNU Public License v2
* or BSD license choice]
* "Dual MPL/GPL" [GNU Public License v2
* or Mozilla license choice]
This distinction was and still is wrong in several aspects:
1) It broke all modules which were using the "GPL" string in the
MODULE_LICENSE() already and were licensed under GPL v2 only.
A quick license scan over the tree at that time shows that at least 480
out of 1484 modules have been affected by this change back then. The
number is probably way higher as this was just a quick check for
clearly identifiable license information.
There was exactly ONE instance of a "GPL v2" module license string in
the kernel back then - drivers/net/tulip/xircom_tulip_cb.c which
otherwise had no license information at all. There is no indication
that the change above is any way related to this driver. The change
happend with the 2.4.11 release which was on Oct. 9 2001 - so quite
some time before the above commit. Unfortunately there is no trace on
the intertubes to any discussion of this.
2) The dual licensed strings became ill defined as well because following
the "GPL" vs. "GPL v2" distinction all dual licensed (or additional
rights) MODULE_LICENSE strings would either require those dual licensed
modules to be licensed under GPL v2 or later or just be unspecified for
the dual licensing case. Neither choice is coherent with the GPL
distinction.
Due to the lack of a proper changelog and no real discussion on the patch
submission other than a few implementation details, it's completely unclear
why this distinction was introduced at all. Other than the comment in the
module header file exists no documentation for this at all.
From a license compliance and license scanning POV this distinction is a
total nightmare.
As of 5.0-rc2 2873 out of 9200 instances of MODULE_LICENSE() strings are
conflicting with the actual license in the source code (either SPDX or
license boilerplate/reference). A comparison between the scan of the
history tree and a scan of current Linus tree shows to the extent that the
git rename detection over Linus tree grafted with the history tree is
halfways complete that almost none of the files which got broken in 2003
have been cleaned up vs. the MODULE_LICENSE string. So subtracting those
480 known instances from the conflicting 2800 of today more than 25% of the
module authors got it wrong and it's a high propability that a large
portion of the rest just got it right by chance.
There is no value for the module loader to convey the detailed license
information as the only decision to be made is whether the module is free
software or not.
The "and additional rights", "BSD" and "MPL" strings are not conclusive
license information either. So there is no point in trying to make the GPL
part conclusive and exact. As shown above it's already non conclusive for
dual licensing and incoherent with a large portion of the module source.
As an unintended side effect this distinction causes a major headache for
license compliance, license scanners and the ongoing effort to clean up the
license mess of the kernel.
Therefore remove the well meant, but ill defined, distinction between "GPL"
and "GPL v2" and document that:
- "GPL" and "GPL v2" both express that the module is licensed under GPLv2
(without a distinction of 'only' and 'or later') and is therefore kernel
license compliant.
- None of the MODULE_LICENSE strings can be used for expressing or
determining the exact license
- Their sole purpose is to decide whether the module is free software or
not.
Add a MODULE_LICENSE subsection to the license rule documentation as well.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Acked-by: Joe Perches <joe@perches.com>
[jc: Did s/merily/merely/ ]
Acked-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
It clarifies that the DMA description pointer returned by
`dmaengine_prep_*` function should not be used after submission.
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix markup warning: insert a blank line before the hint.
Documentation/driver-api/dmaengine/dmatest.rst:63: WARNING: Unexpected indentation.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The 32-bit Amlogic Meson SoCs (Meson6, Meson8, Meson8b and Meson8m2)
have a built-in RTC block.
It has the following inputs:
- an 32.768kHz crystal oscillator
- an interrupt line
- a reset line
- 0.9V voltage input
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
[resurrected patches from Ben after 2 years]
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Chanwoo writes:
Update extcon for 5.1
Detailed description for this pull request:
1. Add new extcon-ptn5150.c extcon provider driver
- NXP PTN5150 supports the detection of USB connectors through
USB Type-C port and controls it. It is interfaced to the host
controller using an I2C interface.
* tag 'extcon-next-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon:
extcon: ptn5150: Fix return value check in ptn5150_i2c_probe()
extcon: Add support for ptn5150 extcon driver
