This has been successfully tested on Netgear R6250 and two other
development (unnamed) devices, all of them BCM4708 based.
We also got a possitive feedback from R7000 (BCM4709) tester.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add a new directory heirarchy under the debugfs sunrpc/ directory:
sunrpc/
rpc_xprt/
<xprt id>/
Within that directory, we can put files that give info about the
xprts. We do have the (minor) problem that there is no succinct,
unique identifier for rpc_xprts. So we generate them synthetically
with a static atomic_t counter.
For now, this directory just holds an "info" file, but we may add
other files to it in the future.
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
It's possible to get a dump of the RPC task queue by writing a value to
/proc/sys/sunrpc/rpc_debug. If you write any value to that file, you get
a dump of the RPC client task list into the log buffer. This is a rather
inconvenient interface however, and makes it hard to get immediate info
about the task queue.
Add a new directory hierarchy under debugfs:
sunrpc/
rpc_clnt/
<clientid>/
Within each clientid directory we create a new "tasks" file that will
dump info similar to what shows up in the log buffer, but with a few
small differences -- we avoid printing raw kernel addresses in favor of
symbolic names and the XID is also displayed.
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
According to the sgtl5000 datasheet the MCLK frequency range restriction of
8 to 27 MHz only applies when the PLL is used - synchronous SYS_MCLK input mode.
mxs-sgtl5000 machine sets the codec as slave, and mx28 generates MCLK in the
range of 256*fs, 384*fs or 512*fs, which is called asynchronous SYS_MCLK
input.
In asynchronous SYS_MCLK we cannot have the 8 to 27 MHz check because if we
want to play a 8KHz sample rate track, with a MCLK of 8k * 512 = 4.096MHz the
current check would return -EINVAL, which is not correct.
Remove the 8 to 27MHz frequency check, since this only applies to the
synchronous SYS_MCLK input case.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When trying to play a 8kHz file with codec in slave mode we get the following
error on a mx28evk:
$ aplay -Dhw:0,0 stereo_8k.wav
Playing WAVE 'stereo_8k.wav' : Signed 16 bit Little Endian, Rate 8000 Hz, Stereo
[ 21.218647] sgtl5000 0-000a: PLL not supported in slave mode
[ 21.224559] sgtl5000 0-000a: 128 ratio is not supported. SYS_MCLK needs to be 256, 384 or 512 * fs
[ 21.233687] sgtl5000 0-000a: ASoC: can't set sgtl5000 hw params: -22
aplay: set_params:1123: Unable to install hw params:
This error happens because we are using 'sys_fs' instead of 'frame_rate' in the
valid ratio check.
Use the real'frame_rate' so that the ratio is correctly calculated and the
playback can run.
sgtl5000 codec manual states that in 'Synchronous SYS_MCLK input' mode that the
following SYS_CLK frequencies are allowed: 256*fs, 384*fs, 512*fs.
, where fs is the sampling frequency, which can be in the range of:
8, 11.025, 16, 22.5, 32, 44.1, 48, 96 kHz.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the sgtl5000 datasheet the MCLK frequency range restriction of
8 to 27 MHz only applies when the PLL is used - synchronous SYS_MCLK input mode.
When running the codec as slave, the master should generate MCLK in the range of
256*fs, 384*fs or 512*fs, which is called asynchronous SYS_MCLK input mode.
In asynchronous SYS_MCLK we cannot have the 8 to 27 MHz check because if we
want to play a 8KHz sample rate track, with a MCLK of 8k * 512 = 4.096MHz the
current check would return -EINVAL, which is not correct.
Remove the 8 to 27MHz frequency check, since this only applies to the
synchronous SYS_MCLK input case.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make the map match the reality, the current binding text is
nonsense:
- The clock required for the clocking of the serial port
must come first and is not optional (as the driver will
otherwise proceed to grab and use the apb_pclk as uartclk),
and the apb_pclk that clocks the logic must come second
as the code will retrieve the first clock by index,
whereas the PrimeCell but will explicitly look for
"apb_pclk" so this can be specified later, as it is
looked up by name.
- The pin control state "default" is the only mandated
state, the sleep state is entirely optional.
We also add an example to avoid further confusion.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
It referenced of_property_read_string_util whereas the function name
is of_property_read_string_helper.
Introduced in a87fa1d81a (of: Fix
overflow bug in string property parsing functions). Found out when
reviewing the stable 3.12 queue.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Instead of keeping track of all those special cases where
VLAN interfaces have no bss_conf.chandef, just make sure
they have the same as the AP interface they belong to.
Among others, this fixes a crash getting a VLAN's channel
from userspace since a NULL channel is returned as a good
result (return value 0) for VLANs since the commit below.
Cc: stable@vger.kernel.org [3.18 only]
Fixes: c12bc4885f ("mac80211: return the vif's chandef in ieee80211_cfg_get_channel()")
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[rewrite commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
One of the cases for an invalid channel definition is that
the channel pointer is NULL, in which case the warning is
a bit late since we'll dereference the pointer. Bail out
of the function upon warning about this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Kishon writes:
Improvements in phy-core specifically on PHY core finds the PHY in the case
of non-dt boot. Adds three new PHY drivers using the PHY framework and some
miscellaneous fixes and cleanups.
There is a potential race when probing the TLB in TLBL/M/S exception
handlers for a matching entry. Between the time we hit a TLBL/S/M
exception and the time we get to execute the TLBP instruction, the
HTW may have replaced the TLB entry we are interested in hence the TLB
probe may fail. However, in the existing handlers, we never checked the
status of the TLBP (ie check the result in the C0/Index register). We
fix this by adding such a check when the core implements the HTW. If
we couldn't find a matching entry, we return back and try again.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.17+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8599/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If somebody causes an unexpected bad IRQ, this even will be unnoticed in
both dmesg and system logs. If the "bad" IRQ is stuck, the device will
just hang silently w/o reporting anything. Compare this to the generic
behaviour (from include/asm-generic/hardirq.h) which prints a message
with critical level. So to help everybody, include the same message into
ARM-specific ack_bad_irq().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use gpio-charger driver instead of pda-power: it automatically cares
about used gpio and since collie does not differentiate between usb and
ac chargers, pda-power is an overkill for it.
As a bonus this allows us to remove gpio_to_irq calls from machine init
call - it is fragile. These gpio_to_irq calls will fail if gpios are
registered later, via device driver mechanisms.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add system suspend/resume capabilities to the pl330 driver so the amba
bus clock could be also unprepared to conserve energy.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The memory copy functions(memcpy, __copy_from_user, __copy_to_user)
never had unwinding annotations added. Currently, when accessing
invalid pointer by these functions occurs the backtrace shown will
stop at these functions or some completely unrelated function.
Add unwinding annotations in hopes of getting a more useful backtrace
in following cases:
1. die on accessing invalid pointer by these functions
2. kprobe trapped at any instruction within these functions
3. interrupted at any instruction within these functions
Signed-off-by: Lin Yongting <linyongting@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The memmove function never had unwinding annotations added.
Currently, when accessing invalid pointer by memmove occurs the
backtrace shown will stop at memmove or some completely unrelated
function. Add unwinding annotations in hopes of getting a more
useful backtrace in following cases:
1. die on accessing invalid pointer by memmove
2. kprobe trapped at any instruction within memmove
3. interrupted at any instruction within memmove
Signed-off-by: Lin Yongting <linyongting@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The __memzero function never had unwinding annotations added.
Currently, when accessing invalid pointer by __memzero occurs the
backtrace shown will stop at __memzero or some completely unrelated
function. Add unwinding annotations in hopes of getting a more
useful backtrace in following cases:
1. die on accessing invalid pointer by __memzero
2. kprobe trapped at any instruction within __memzero
3. interrupted at any instruction within __memzero
Signed-off-by: Lin Yongting <linyongting@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We cannot restart cacheflush safely if a process provides user-defined
signal handler and signal is pending. In this case -EINTR is returned
and it is expected that process re-invokes syscall. However, there are
a few problems with that:
* looks like nobody bothers checking return value from cacheflush
* but if it did, we don't provide the restart address for that, so the
process has to use the same range again
* ...and again, what might lead to looping forever
So, remove cacheflush restarting code and terminate cache flushing
as early as fatal signal is pending.
Cc: stable@vger.kernel.org # 3.12+
Reported-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Under extremely rare conditions, in an MPCore node consisting of at
least 3 CPUs, two CPUs trying to perform a STREX to data on the same
shared cache line can enter a livelock situation.
This patch enables the HW mechanism that overcomes the bug. This fixes
the incorrect setup of the STREX backoff delay bit due to a wrong
description in the specification.
Note that enabling the STREX backoff delay mechanism is done by
leaving the bit *cleared*, while the bit was currently being set by
the proc-v7.S code.
[Thomas: adapt to latest mainline, slightly reword the commit log, add
stable markers.]
Fixes: de4901933f ("arm: mm: Add support for PJ4B cpu and init routines")
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The task_collector mode (or "latency_injector", (C) Dan Willians) is an
optional I/O path in libsas that queues up scsi commands instead of
directly sending it to the hardware. It generall increases latencies
to in the optiomal case slightly reduce mmio traffic to the hardware.
Only the obsolete aic94xx driver and the mvsas driver allowed to use
it without recompiling the kernel, and most drivers didn't support it
at all.
Remove the giant blob of code to allow better optimizations for scsi-mq
in the future.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Remove dma_cache_sync call to fix build on other architectures.
Driver still works fine on x86 without that.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Since 3b26f39b0a (ARM: at91: make use of the new AIC driver for dt enabled
boards) the old IRQ initialisation functions aren't used anymore: remove their
declaration in generic.h.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Remove irc.c and associated header file. The related code was idendified by
the CONFIG_OLD_IRQ_AT91 option that was removed previously. It has been spotted
by following coccinelle semantic match:
@rule1@
expression E;
statement S;
@@
(
- if (IS_ENABLED(CONFIG_OLD_IRQ_AT91)) S
|
- if (IS_ENABLED(CONFIG_OLD_IRQ_AT91) && E) S
)
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Otherwise we'd still end up w/ the plane attached to the CRTC, and
seemingly active, but without an FB. Which ends up going *boom*
in the drivers.
Slightly modified version of Daniel's irc suggestion.
Note that the big problem isn't drivers going *boom* here (since we
already have the situation of planes being left enabled when the crtc
goes down). The real issue is that the core assumes the primary plane
always goes down when calling ->set_config with a NULL mode. Ignoring
that assumption leads to the legacy state pointers plane->fb/crtc
getting out of sync with atomic, and that then leads to the subsequent
*boom* all over the place.
CC: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Rob Clark <robdclark@gmail.com>
[danvet: Drop my opinion of what's going sidewides here into the
commit message as a note.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So the problem with async commit (especially async modeset commit) is
that the legacy pointers only get updated after the point of no
return, in the async part of the modeset sequence. At least as
implemented by the current helper functions. This is done in the
set_routing_links function in drm_atomic_helper.c.
Which also means that access isn't protected by locks but only
coordinated by synchronizing with async workers. No problem thus far,
until we lock at the getconnector/encoder ioctls.
So fix this up by adding special cases for atomic drivers: For those
we need to look at state objects. Unfortunately digging out the
correct encoder->crtc link is a bit of work, so wrap this up in a
helper function.
Moving the assignments of connector->encoder and encoder->crtc earlier
isn't a good idea because the point of the atomic helpers is that we
stage the state updates. That way the disable functions can still
inspect the links and rely upon them.
v2: Extract full encoder->crtc lookup into helper (Rob).
v3: Extract drm_connector_get_encoder too since - we need to always
return state->best_encoder when there is a state otherwise we might
return stale data if there's a pending async disable (and chase
unlocked pointers, too). Same issue with encoder_get_crtc but there
it's a bit more tricky to handle.
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Lightly-Tested-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Add helper macros to iterate the current, or incoming set of planes
attached to a crtc. These helpers are only available for drivers
converted to use atomic-helpers.
Signed-off-by: Rob Clark <robdclark@gmail.com>
[danvet: Squash in fixup from Rob to move the planemask iterator to
drm_crtc.h and document it. That one is needed by the atomic ioctl so
can't be in a helper library.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chasing plane->state->crtc of planes that are *not* part of the same
atomic update is racy, making it incredibly awkward (or impossible) to
do something simple like iterate over all planes and figure out which
ones are attached to a crtc.
Solve this by adding a bitmask of currently attached planes in the
crtc-state.
Note that the transitional helpers do not maintain the plane_mask. But
they only support the legacy ioctls, which have sufficient brute-force
locking around plane updates that they can continue to loop over all
planes to see what is attached to a crtc the old way.
Signed-off-by: Rob Clark <robdclark@gmail.com>
[danvet:
- Drop comments about locking in set_crtc_for_plane since they're a
bit misleading - we already should hold lock for the current crtc.
- Also WARN_ON if get_state on the old crtc fails since that should
have been done already.
- Squash in fixup to check get_plane_state return value, reported by
Dan Carpenter and acked by Rob Clark.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Compiler dead store optimization can sometimes remove final calls
to memset() used to clear sensitive data at the end of a function.
Replace trailing memset() calls with memzero_explicit() to
preclude unwanted removal.
Signed-off-by: Nickolaus Woodruff <nickolauswoodruff@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
It doesn't make much sense to make some (possible expensive) calls to
gpio_is_valid() first, and to ignore the result if the base number is
negative. Check for a positive base number first.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If devm_request_threaded_irq fails for some reason we call
mcp23s08_irq_teardown afterwards.
Do not free the unrequested interrupt in this case. free_irq can also be
omitted for the error free case because we use devm_request_threaded_irq.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a set_multiple function to the MPC8xxx GPIO chip driver and thereby allow
for actual performance improvements when setting multiple outputs
simultaneously. In my case the time needed to configure an FPGA goes down from
48 s to 20 s.
Change log:
v6: - rebase on current linux-gpio devel branch
v5: - no change
v4: - change interface of the set_multiple driver function to use
unsigned long as type for the bit fields
- use generic bitops (which also use unsigned long for bit fields)
v3: - change commit message
v2: - add this patch (v1 included only changes to gpiolib)
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer
interface which allow setting multiple outputs with just one function call.
Also add an optional set_multiple function to the driver interface. Without an
implementation of that function in the chip driver outputs are set
sequentially.
Implementing the set_multiple function in a chip driver allows for:
- Improved performance for certain use cases. The original motivation for this
was the task of configuring an FPGA. In that specific case, where 9 GPIO
lines have to be set many times, configuration time goes down from 48 s to
20 s when using the new function.
- Simultaneous glitch-free setting of multiple pins on any kind of parallel
bus attached to GPIOs provided they all reside on the same chip and bank.
Limitations:
Performance is only improved for normal high-low outputs. Open drain and
open source outputs are always set separately from each other. Those kinds
of outputs could probably be accelerated in a similar way if we could
forgo the error checking when setting GPIO directions.
Change log:
v6: - rebase on current linux-gpio devel branch
v5: - check can_sleep property per chip
- remove superfluous checks
- supplement documentation
v4: - add gpiod_set_array function for setting logical values
- change interface of the set_multiple driver function to use
unsigned long as type for the bit fields
- use generic bitops (which also use unsigned long for bit fields)
- do not use ARCH_NR_GPIOS any more
v3: - add documentation
- change commit message
v2: - use descriptor interface
- allow arbitrary groups of GPIOs spanning multiple chips
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is not necessarily sufficient to look only at the physical and logical
usages when determining if a field is for the pen or touch. Some fields
are not contained in a sub-collection and thus only have an application
usage. Not checking the application usage in such cases causes us to
ignore the field entirely, which may lead to incorrect behavior.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
