Add initial dt bindings for the interconnects inside i.MX chips.
Multiple external IPs are involved but SOC integration means the
software controllable interfaces are very similar.
Main NOC node acts as interconnect provider if #interconnect-cells is
present. Currently there is a single imx interconnect provider for the
whole SOC.
Other pieces of scalable interconnects can be present, each with their
own OPP table.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/8b341d91e9aee679ae69feb22a2c842b2aeb2137.1586174566.git.leonard.crestez@nxp.com
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
The arm64 kernel's segment alignment is fixed at 64 KB for any page
size, and relocatable kernels are able to fix up any misalignment of
the kernel image with respect to the 2 MB section alignment that is
mandated by the arm64 boot protocol.
Let's increase the PE/COFF section alignment to the same value, so that
kernels loaded by the UEFI PE/COFF loader are guaranteed to end up at
an address that doesn't require any reallocation to be done if the
kernel is relocatable.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20200413155521.24698-6-ardb@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Add the syscfg-fmp property in each i2c node in order to allow
Fast Mode Plus speed if clock-frequency >= 1MHz is indicated.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Commit 28b1a824a4 ("arm64: vdso: Substitute gettimeofday() with C
implementation") introduced an unused 'VDSO_LDFLAGS' variable to the
vdso Makefile, suggesting that we should be passing '-Bsymbolic' to the
linker, as we do when linking the compat vDSO.
Although it's not strictly necessary to pass this flag, it would be
required if we were to add any internal references to the exported
symbols. It's also consistent with how we link the compat vdso so, since
there's no real downside from passing it, add '-Bsymbolic' to the ldflags
for the native vDSO.
Fixes: 28b1a824a4 ("arm64: vdso: Substitute gettimeofday() with C implementation")
Reported-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20200428150854.33130-1-vincenzo.frascino@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
If we do
% echo 1 > /sys/module/dmatest/parameters/run
[ 115.851124] dmatest: Could not start test, no channels configured
% echo dma8chan7 > /sys/module/dmatest/parameters/channel
[ 127.563872] dmatest: Added 1 threads using dma8chan7
% cat /sys/module/dmatest/parameters/wait
... !!! HANG !!! ...
The culprit is the commit 6138f967bc
("dmaengine: dmatest: Use fixed point div to calculate iops")
which makes threads not to run, but pending and being kicked off by writing
to the 'run' node. However, it forgot to consider 'wait' routine to avoid
above mentioned case.
In order to fix this, check for really running threads, i.e. with pending
and done flags unset.
It's pity the culprit commit hadn't updated documentation and tested all
possible scenarios.
Fixes: 6138f967bc ("dmaengine: dmatest: Use fixed point div to calculate iops")
Cc: Seraj Alijan <seraj.alijan@sondrel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200428113518.70620-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The BD71837 had a HW "feature" where changing the regulator output
voltages of other regulators but bucks 1-4 might cause spikes if
regulators were enabled. Thus SW prohibit voltage changes for other
regulators except for bucks 1-4 when regulator is enabled.
The HW colleagues did inadvertly fix this issue for BD71847 and
BD71850. Remove voltage change restrictions from other PMICs but
BD71837.
The LDO voltage changing is still restricted. I did not yet receive
answer whether there is voltage spikes to be expected for LDOs. I
only know that the power-good detection for LDOs can cause false
alarms if LDO voltage is changed when LDO is enabled. We might be
able to work-around this by disabling the power-good monioring for
the duration of the LDO voltage change - but as I said, I don't
know yet. Let's fix it later if we can confirm that also LDO voltage
changes are safe.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/20200428092930.GA9721@localhost.localdomain
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull s390 fix from Christian Borntraeger:
"Fix a race between page table upgrade and uaccess on s390.
This fixes CVE-2020-11884 which allows for a local kernel crash or
code execution"
* tag 'cve-2020-11884' from emailed bundle:
s390/mm: fix page table upgrade vs 2ndary address mode accesses
In commit c8c43cee29 ("driver core: Fix
driver_deferred_probe_check_state() logic"), we set the default
driver_deferred_probe_timeout value to 30 seconds to allow for
drivers that are missing dependencies to have some time so that
the dependency may be loaded from userland after initcalls_done
is set.
However, Yoshihiro Shimoda reported that on his device that
expects to have unmet dependencies (due to "optional links" in
its devicetree), was failing to mount the NFS root.
In digging further, it seemed the problem was that while the
device properly probes after waiting 30 seconds for any missing
modules to load, the ip_auto_config() had already failed,
resulting in NFS to fail. This was due to ip_auto_config()
calling wait_for_device_probe() which doesn't wait for the
driver_deferred_probe_timeout to fire.
This patch tries to fix the issue by creating a waitqueue
for the driver_deferred_probe_timeout, and calling wait_event()
to make sure driver_deferred_probe_timeout is zero in
wait_for_device_probe() to make sure all the probing is
finished.
The downside to this solution is that kernel functionality that
uses wait_for_device_probe(), will block until the
driver_deferred_probe_timeout fires, regardless of if there is
any missing dependencies.
However, the previous patch reverts the default timeout value to
zero, so this side-effect will only affect users who specify a
driver_deferred_probe_timeout= value as a boot argument, where
the additional delay would be beneficial to allow modules to
load later during boot.
Thanks to Geert for chasing down that ip_auto_config was why NFS
was failing in this case!
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Rob Herring <robh@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Basil Eljuse <Basil.Eljuse@arm.com>
Cc: Ferry Toth <fntoth@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Anders Roxell <anders.roxell@linaro.org>
Cc: linux-pm@vger.kernel.org
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: c8c43cee29 ("driver core: Fix driver_deferred_probe_check_state() logic")
Signed-off-by: John Stultz <john.stultz@linaro.org>
Link: https://lore.kernel.org/r/20200422203245.83244-4-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch addresses a regression in 5.7-rc1+
In commit c8c43cee29 ("driver core: Fix
driver_deferred_probe_check_state() logic"), we both cleaned up
the logic and also set the default driver_deferred_probe_timeout
value to 30 seconds to allow for drivers that are missing
dependencies to have some time so that the dependency may be
loaded from userland after initcalls_done is set.
However, Yoshihiro Shimoda reported that on his device that
expects to have unmet dependencies (due to "optional links" in
its devicetree), was failing to mount the NFS root.
In digging further, it seemed the problem was that while the
device properly probes after waiting 30 seconds for any missing
modules to load, the ip_auto_config() had already failed,
resulting in NFS to fail. This was due to ip_auto_config()
calling wait_for_device_probe() which doesn't wait for the
driver_deferred_probe_timeout to fire.
Fixing that issue is possible, but could also introduce 30
second delays in bootups for users who don't have any
missing dependencies, which is not ideal.
So I think the best solution to avoid any regressions is to
revert back to a default timeout value of zero, and allow
systems that need to utilize the timeout in order for userland
to load any modules that supply misisng dependencies in the dts
to specify the timeout length via the exiting documented boot
argument.
Thanks to Geert for chasing down that ip_auto_config was why NFS
was failing in this case!
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Rob Herring <robh@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Basil Eljuse <Basil.Eljuse@arm.com>
Cc: Ferry Toth <fntoth@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Anders Roxell <anders.roxell@linaro.org>
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: c8c43cee29 ("driver core: Fix driver_deferred_probe_check_state() logic")
Signed-off-by: John Stultz <john.stultz@linaro.org>
Link: https://lore.kernel.org/r/20200422203245.83244-2-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When commit 8375e74f2b ("driver core: Add fw_devlink kernel
commandline option") added fw_devlink, it didn't implement "permissive"
mode correctly.
That commit got the device links flags correct to make sure unprobed
suppliers don't block the probing of a consumer. However, if a consumer
is waiting for mandatory suppliers to register, that could still block a
consumer from probing.
This commit fixes that by making sure in permissive mode, all suppliers
to a consumer are treated as a optional suppliers. So, even if a
consumer is waiting for suppliers to register and link itself (using the
DL_FLAG_SYNC_STATE_ONLY flag) to the supplier, the consumer is never
blocked from probing.
Fixes: 8375e74f2b ("driver core: Add fw_devlink kernel commandline option")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200331022832.209618-1-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's currently the amba driver's responsibility to initialize the pointer,
dma_parms, for its corresponding struct device. The benefit with this
approach allows us to avoid the initialization and to not waste memory for
the struct device_dma_parameters, as this can be decided on a case by case
basis.
However, it has turned out that this approach is not very practical. Not
only does it lead to open coding, but also to real errors. In principle
callers of dma_set_max_seg_size() doesn't check the error code, but just
assumes it succeeds.
For these reasons, let's do the initialization from the common amba bus at
the device registration point. This also follows the way the PCI devices
are being managed, see pci_device_add().
Suggested-by: Christoph Hellwig <hch@lst.de>
Cc: Russell King <linux@armlinux.org.uk>
Cc: <stable@vger.kernel.org>
Tested-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20200422101013.31267-1-ulf.hansson@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's currently the platform driver's responsibility to initialize the
pointer, dma_parms, for its corresponding struct device. The benefit with
this approach allows us to avoid the initialization and to not waste memory
for the struct device_dma_parameters, as this can be decided on a case by
case basis.
However, it has turned out that this approach is not very practical. Not
only does it lead to open coding, but also to real errors. In principle
callers of dma_set_max_seg_size() doesn't check the error code, but just
assumes it succeeds.
For these reasons, let's do the initialization from the common platform bus
at the device registration point. This also follows the way the PCI devices
are being managed, see pci_device_add().
Suggested-by: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org>
Tested-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20200422100954.31211-1-ulf.hansson@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hwmgr->pm_en is initialized at hwmgr_hw_init.
during amdgpu_device_init, there is amdgpu_asic_reset that calls to
soc15_asic_reset (for V320 usecase, Vega10 asic), in which:
1) soc15_asic_reset_method calls to pp_get_asic_baco_capability (pm_en)
2) soc15_asic_baco_reset calls to pp_set_asic_baco_state (pm_en)
pm_en is used in the above two cases while it has not yet been initialized
So avoid using pm_en in the above two functions for V320 passthrough.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Tiecheng Zhou <Tiecheng.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This series provides the following updtes to the Intel machine driver
Kconfig:
1. The first patch adds the explicit dependency on GPIOLIB when
SND_SOC_DMIC is selected.
2. SND_SOC_SOF_HDA_AUDIO_CODEC is required for using the legacy
HDA codec driver for HDMI support in SOF. The last 3 three patches
make the required changes to account for this.
Libin Yang (3):
ASoC: intel: add depends on SND_SOC_SOF_HDA_AUDIO_CODEC for common
hdmi
ASoC: sof-sdw: remove CONFIG_SND_SOC_SOF_HDA_AUDIO_CODEC condition
ASoC: sof_pcm512x: remove CONFIG_SND_HDA_CODEC_HDMI condition
Pierre-Louis Bossart (1):
ASoC: Intel: boards: add explicit dependency on GPIOLIB when DMIC is
used
sound/soc/intel/boards/Kconfig | 51 ++++++++++++++-------------
sound/soc/intel/boards/sof_pcm512x.c | 9 -----
sound/soc/intel/boards/sof_sdw.c | 8 -----
sound/soc/intel/boards/sof_sdw_hdmi.c | 7 ----
4 files changed, 26 insertions(+), 49 deletions(-)
--
2.17.1
The machine driver bdw-rt5650 (for Google buddy) supports 2 or 4-channel
recording while other two drivers support only 2-channel recording. HW
constraints are implemented to reflect the hardware limitation on BDW
platform.
Changes since v1:
- Change the patch title.
- Remove the DUAL_CHANNEL and QUAD_CHANNEL macros which are too obvious.
- Follow the naming convertion, using 'bdw_rt5650_' and 'bdw_rt5677_' to
name startup functions.
- Refine the comments in startup functions.
- Redesign the bdw_rt5650_fe_startup() function for readability.
- Add an assignment to initialize runtime->hw.channels_max variable.
Brent Lu (3):
ASoC: bdw-rt5677: add channel constraint
ASoC: bdw-rt5650: add channel constraint
ASoC: broadwell: add channel constraint
sound/soc/intel/boards/bdw-rt5650.c | 29 +++++++++++++++++++++++++++++
sound/soc/intel/boards/bdw-rt5677.c | 26 ++++++++++++++++++++++++++
sound/soc/intel/boards/broadwell.c | 26 ++++++++++++++++++++++++++
3 files changed, 81 insertions(+)
--
2.7.4
Add declarations related to the syscon pdds for deep sleep management.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Some processes, such as systemd, are only polling for EPOLLERR|EPOLLHUP.
As drm_file uses unkeyed wakeups, such a poll receives many spurious
wakeups from uninteresting events.
Use keyed wakeups to allow the wakeup target to more efficiently discard
these uninteresting events.
Signed-off-by: Kenny Levinsen <kl@kl.wtf>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200424145103.3048-1-kl@kl.wtf
In order to surface the ASIC revision to user level, we want
to put it into the HSA topology. This can be because different
ASIC revisions may require user-level software to do different
things (e.g. patch code for things that are changed in later
hardware revisions).
The ASIC revision from the hardware is maximum of 4 bits at this
time, so put it into 4 of the open bits in the HSA capability.
Then user-level software can use this capability information to
know -- for each ASIC -- what revision-based things must be done.
Signed-off-by: Joseph Greathouse <Joseph.Greathouse@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The Hulk robot reports these build warnings:
drivers/pinctrl/nomadik/pinctrl-nomadik-db8500.c:899:20: warning:
‘sbag_groups’ defined but not used [-Wunused-const-variable=]
DB8500_FUNC_GROUPS(sbag, "sbag_oc2_1", "sbag_oc4_1");
^
drivers/pinctrl/nomadik/pinctrl-nomadik-db8500.c:570:23: warning:
‘ipgpio6_c_2_pins’ defined but not used [-Wunused-const-variable=]
static const unsigned ipgpio6_c_2_pins[] = { DB8500_PIN_G3 };
^~~~~~~~~~~~~~~~
drivers/pinctrl/nomadik/pinctrl-nomadik-db8500.c:472:23: warning:
‘mc1dir_a_1_pins’ defined but not used [-Wunused-const-variable=]
static const unsigned mc1dir_a_1_pins[] = { DB8500_PIN_AH13,
DB8500_PIN_AG12,
^~~~~~~~~~~~~~~
drivers/pinctrl/nomadik/pinctrl-nomadik-db8500.c:453:23: warning:
‘modem_a_1_pins’ defined but not used [-Wunused-const-variable=]
static const unsigned modem_a_1_pins[] = { DB8500_PIN_D22,
DB8500_PIN_C23,
^~~~~~~~~~~~~~
drivers/pinctrl/nomadik/pinctrl-nomadik-db8500.c:430:23: warning:
‘kpskaskb_a_1_pins’ defined but not used [-Wunused-const-variable=]
static const unsigned kpskaskb_a_1_pins[] = { DB8500_PIN_D17,
DB8500_PIN_D16 };
^~~~~~~~~~~~~~~~~
They are just very old bugs in seldomly used pin groups.
Fix the problem by using the pins and referencing the
function.
Reported-by: Hulk Robot <hulkci@huawei.com>
Reported-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Hulk robot reports an usused varible:
drivers/pinctrl/nomadik/pinctrl-ab8505.c:137:23: warning:
‘gpio50_a_1_pins’ defined but not used [-Wunused-const-variable=]
static const unsigned gpio50_a_1_pins[] = { AB8505_PIN_L4 };
^~~~~~~~~~~~~~~
This variable actually should be used. Probably an oversight
by the driver author.
Cc: Patrice Chotard <patrice.chotard@st.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Reported-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver currently leaves GPIO IRQs unmasked even when the GPIO IRQ
client has released the GPIO IRQ. This allows the HW to raise IRQs, and
SW to process them, after shutdown. Fix this by masking the IRQ when it's
shut down. This is usually taken care of by the irqchip core, but since
this driver has a custom irq_shutdown implementation, it must do this
explicitly itself.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Link: https://lore.kernel.org/r/20200427232605.11608-1-swarren@wwwdotorg.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A race exists between build_pcms() and build_controls() phases of codec
setup. Build_pcms() sets up notifier for jack events. If a monitor event
is received before build_controls() is run, the initial jack state is
lost and never reported via mixer controls.
The problem can be hit at least with SOF as the controller driver. SOF
calls snd_hda_codec_build_controls() in its workqueue-based probe and
this can be delayed enough to hit the race condition.
Fix the issue by invalidating the per-pin ELD information when
build_controls() is called. The existing call to hdmi_present_sense()
will update the ELD contents. This ensures initial monitor state is
correctly reflected via mixer controls.
BugLink: https://github.com/thesofproject/linux/issues/1687
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200428123836.24512-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Komeda uses the component framework, which does open/close a new
devres group around all the bind callbacks. Which means we can use
devm_ functions for managing the drm_device cleanup, with leaking
stuff in case of deferred probes or other reasons to unbind
components, or the component_master.
Also note that this fixes a double-free in the probe unroll code, bot
drm_dev_put and kfree(kms) result in the kms allocation getting freed.
Aside: komeda_bind could be cleaned up a lot, devm_kfree is a bit
redundant. Plus I'm not clear on why there's suballocations for
mdrv->mdev and mdrv->kms. Plus I'm not sure the lifetimes are correct
with all that devm_kzalloc usage ... That structure layout is also the
reason why komeda still uses drm_device->dev_private and can't easily
be replaced with a proper container_of upcasting. I'm pretty sure that
there's endless amounts of hotunplug/hotremove bugs in there with all
the unprotected dereferencing of drm_device->dev_private.
Reviewed-by: James Qian Wang <james.qian.wang@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: "James (Qian) Wang" <james.qian.wang@arm.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Mihail Atanassov <mihail.atanassov@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200415074034.175360-33-daniel.vetter@ffwll.ch
