Currently the macro that inserts entries into the SPU syscall table
doesn't actually use the "nr" (syscall number) parameter.
This does work, but it relies on the exact right number of syscall
entries being emitted in order for the syscal numbers to line up with
the array entries. If for example we had two entries with the same
syscall number we wouldn't get an error, it would just cause all
subsequent syscalls to be off by one in the spu_syscall_table.
So instead change the macro to assign to the specific entry of the
array, meaning any numbering overlap will be caught by the compiler.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200616135617.2937252-1-mpe@ellerman.id.au
The pte_update() implementation for PPC_8xx unfolds page table from the PGD
level to access a PMD entry. Since 8xx has only 2-level page table this can
be simplified with pmd_off() shortcut.
Replace explicit unfolding with pmd_off() and drop defines of pgd_index()
and pgd_offset() that are no longer needed.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200615092229.23142-1-rppt@kernel.org
In case of -EPROBE_DEFER, stm32_qspi_release() was called
in any case which unregistered driver from pm_runtime framework
even if it has not been registered yet to it. This leads to:
stm32-qspi 58003000.spi: can't setup spi0.0, status -13
spi_master spi0: spi_device register error /soc/spi@58003000/mx66l51235l@0
spi_master spi0: Failed to create SPI device for /soc/spi@58003000/mx66l51235l@0
stm32-qspi 58003000.spi: can't setup spi0.1, status -13
spi_master spi0: spi_device register error /soc/spi@58003000/mx66l51235l@1
spi_master spi0: Failed to create SPI device for /soc/spi@58003000/mx66l51235l@1
On v5.7 kernel,this issue was not "visible", qspi driver was probed
successfully.
Fixes: 9d282c17b0 ("spi: stm32-qspi: Add pm_runtime support")
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Link: https://lore.kernel.org/r/20200616113035.4514-1-patrice.chotard@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Unfortunately, most versions of clang that support BTI are capable of
miscompiling the kernel when converting a switch statement into a jump
table. As an example, attempting to spawn a KVM guest results in a panic:
[ 56.253312] Kernel panic - not syncing: bad mode
[ 56.253834] CPU: 0 PID: 279 Comm: lkvm Not tainted 5.8.0-rc1 #2
[ 56.254225] Hardware name: QEMU QEMU Virtual Machine, BIOS 0.0.0 02/06/2015
[ 56.254712] Call trace:
[ 56.254952] dump_backtrace+0x0/0x1d4
[ 56.255305] show_stack+0x1c/0x28
[ 56.255647] dump_stack+0xc4/0x128
[ 56.255905] panic+0x16c/0x35c
[ 56.256146] bad_el0_sync+0x0/0x58
[ 56.256403] el1_sync_handler+0xb4/0xe0
[ 56.256674] el1_sync+0x7c/0x100
[ 56.256928] kvm_vm_ioctl_check_extension_generic+0x74/0x98
[ 56.257286] __arm64_sys_ioctl+0x94/0xcc
[ 56.257569] el0_svc_common+0x9c/0x150
[ 56.257836] do_el0_svc+0x84/0x90
[ 56.258083] el0_sync_handler+0xf8/0x298
[ 56.258361] el0_sync+0x158/0x180
This is because the switch in kvm_vm_ioctl_check_extension_generic()
is executed as an indirect branch to tail-call through a jump table:
ffff800010032dc8: 3869694c ldrb w12, [x10, x9]
ffff800010032dcc: 8b0c096b add x11, x11, x12, lsl #2
ffff800010032dd0: d61f0160 br x11
However, where the target case uses the stack, the landing pad is elided
due to the presence of a paciasp instruction:
ffff800010032e14: d503233f paciasp
ffff800010032e18: a9bf7bfd stp x29, x30, [sp, #-16]!
ffff800010032e1c: 910003fd mov x29, sp
ffff800010032e20: aa0803e0 mov x0, x8
ffff800010032e24: 940017c0 bl ffff800010038d24 <kvm_vm_ioctl_check_extension>
ffff800010032e28: 93407c00 sxtw x0, w0
ffff800010032e2c: a8c17bfd ldp x29, x30, [sp], #16
ffff800010032e30: d50323bf autiasp
ffff800010032e34: d65f03c0 ret
Unfortunately, this results in a fatal exception because paciasp is
compatible only with branch-and-link (call) instructions and not simple
indirect branches.
A fix is being merged into Clang 10.0.1 so that a 'bti j' instruction is
emitted as an explicit landing pad in this situation. Make in-kernel
BTI depend on that compiler version when building with clang.
Cc: Tom Stellard <tstellar@redhat.com>
Cc: Daniel Kiss <daniel.kiss@arm.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20200615105524.GA2694@willie-the-truck
Link: https://lore.kernel.org/r/20200616183630.2445-1-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
The callers don't expect *d_cdp to be set to an error pointer, they only
check for NULL. This leads to a static checker warning:
arch/x86/kernel/cpu/resctrl/rdtgroup.c:2648 __init_one_rdt_domain()
warn: 'd_cdp' could be an error pointer
This would not trigger a bug in this specific case because
__init_one_rdt_domain() calls it with a valid domain that would not have
a negative id and thus not trigger the return of the ERR_PTR(). If this
was a negative domain id then the call to rdt_find_domain() in
domain_add_cpu() would have returned the ERR_PTR() much earlier and the
creation of the domain with an invalid id would have been prevented.
Even though a bug is not triggered currently the right and safe thing to
do is to set the pointer to NULL because that is what can be checked for
when the caller is handling the CDP and non-CDP cases.
Fixes: 52eb74339a ("x86/resctrl: Fix rdt_find_domain() return value and checks")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
Link: https://lkml.kernel.org/r/20200602193611.GA190851@mwanda
Compared to its predecessors, the PX30 VOP has a different register layout
for enabling per-pixel alpha. Instead of src_alpha_ctl and dst_alpha_ctl,
there is a single alpha control register. This register takes some fields
from src_alpha_ctl, but with a different layout.
Add support for the required fields to the PX30 VOP window descriptions,
which makes per-pixel-alpha formats behave correctly.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20200416140526.262533-1-paul.kocialkowski@bootlin.com
The revision rk3288w has a different clock tree about "hclk_vio"
clock, according to the BSP kernel code.
This patch handles this difference by detecting which device-tree
we are using. If it is a "rockchip,rk3288-cru", let's register
the clock tree as it was before. If the device-tree node is
"rockchip,rk3288w-cru", we will apply the difference with this
version of this SoC.
Noticed that this new device-tree compatible must be handled in
bootloader such as u-boot.
Signed-off-by: Mylène Josserand <mylene.josserand@collabora.com>
Link: https://lore.kernel.org/r/20200602080644.11333-2-mylene.josserand@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Fix -Wmissing-prototypes warnings:
arch/x86/mm/init.c:81:6:
warning: no previous prototype for ‘x86_has_pat_wp’ [-Wmissing-prototypes]
bool x86_has_pat_wp(void)
arch/x86/mm/init.c:86:22:
warning: no previous prototype for ‘pgprot2cachemode’ [-Wmissing-prototypes]
enum page_cache_mode pgprot2cachemode(pgprot_t pgprot)
by including the respective header containing prototypes. Also fix:
arch/x86/mm/init.c:893:13:
warning: no previous prototype for ‘mem_encrypt_free_decrypted_mem’ [-Wmissing-prototypes]
void __weak mem_encrypt_free_decrypted_mem(void) { }
by making it static inline for the !CONFIG_AMD_MEM_ENCRYPT case. This
warning happens when CONFIG_AMD_MEM_ENCRYPT is not enabled (defconfig
for example):
./arch/x86/include/asm/mem_encrypt.h:80:27:
warning: inline function ‘mem_encrypt_free_decrypted_mem’ declared weak [-Wattributes]
static inline void __weak mem_encrypt_free_decrypted_mem(void) { }
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
It's ok to convert to static inline because the function is used only in
x86. Is not shared with other architectures so drop the __weak too.
[ bp: Massage and adjust __weak comments while at it. ]
Signed-off-by: Benjamin Thiel <b.thiel@posteo.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200606122629.2720-1-b.thiel@posteo.de
A test with the command below gives for example this error:
arch/arm/boot/dts/rk3288-tinker.dt.yaml: tsadc: otp-gpio:
{'phandle': [[54]], 'rockchip,pins': [[0, 10, 0, 118]]}
is not of type 'array'
'gpio' is a sort of reserved nodename and should not be used
for pinctrl in combination with 'rockchip,pins', so change
nodes that end with 'gpio' to end with 'pin' or 'pins'.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/
dtschema/schemas/gpio/gpio.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200524160636.16547-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Current dts files with 'gpio-led' nodes were manually verified.
In order to automate this process leds-gpio.txt
has been converted to yaml. With this conversion a check
for pattern properties was added. In part 2 rename and label
gpio-led subnodes that passed the regex, but still don't have
the preferred form. Any pin subnode that ends with '-gpio'
in the pinctrl node generates a warning.
Fix with help of the following rules:
1: Add nodename in the preferred form.
2: Always add a label that ends with '_led' to prevent conflicts
with other labels such as 'power' and 'mmc'
3: If leds need pinctrl add a label that ends with '_led_pin'
also to prevent conflicts with other labels.
patternProperties:
# The first form is preferred, but fall back to just 'led'
# anywhere in the node name to at least catch some child nodes.
"(^led-[0-9a-f]$|led)":
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/leds/
leds-gpio.yaml
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/
schemas/gpio/gpio.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200522154657.9472-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives for example this error:
arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dt.yaml:
tsadc: tsadc-otp-gpio:
{'phandle': [[90]], 'rockchip,pins': [[0, 6, 0, 123]]}
is not of type 'array'
'gpio' is a sort of reserved nodename and should not be used
for pinctrl in combination with 'rockchip,pins', so change
nodes that end with 'gpio' to end with 'pin' or 'pins'.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/
dtschema/schemas/gpio/gpio.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200524160636.16547-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The puma gmac node currently uses opposite active-values for the
gmac phy reset pin. The gpio-declaration uses active-high while the
separate snps,reset-active-low property marks the pin as active low.
While on the kernel side this works ok, other DT users may get
confused - as seen with uboot right now.
So bring this in line and make both properties match, similar to the
other Rockchip board.
Fixes: 2c66fc34e9 ("arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM")
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Link: https://lore.kernel.org/r/20200603132836.362519-1-heiko@sntech.de
The puma vcc5v0_host regulator node currently uses opposite active-values
for the enable pin. The gpio-declaration uses active-high while the
separate enable-active-low property marks the pin as active low.
While on the kernel side this works ok, other DT users may get
confused - as seen with uboot right now.
So bring this in line and make both properties match, similar to the
gmac fix.
Fixes: 2c66fc34e9 ("arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM")
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Link: https://lore.kernel.org/r/20200604091239.424318-1-heiko@sntech.de
The lion gmac node currently uses opposite active-values for the
gmac phy reset pin. The gpio-declaration uses active-high while the
separate snps,reset-active-low property marks the pin as active low.
While on the kernel side this works ok, other DT users may get
confused - as seen with uboot right now.
So bring this in line and make both properties match, similar to the
other Rockchip board.
Fixes: d99a02bcfa ("arm64: dts: rockchip: add RK3368-uQ7 (Lion) SoM")
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Link: https://lore.kernel.org/r/20200607212909.920575-1-heiko@sntech.de
With the recent full-duplex support of implicit feedback streams, an
endpoint can be still running after closing the capture stream as long
as the playback stream with the sync-endpoint is running. In such a
state, the URBs are still be handled and they may call retire_data_urb
callback, which tries to transfer the data from the PCM buffer. Since
the PCM stream gets closed, this may lead to use-after-free.
This patch adds the proper clearance of the callback at stopping the
capture stream for addressing the possible UAF above.
Fixes: 10ce77e481 ("ALSA: usb-audio: Add duplex sound support for USB devices using implicit feedback")
Link: https://lore.kernel.org/r/20200616120921.12249-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
__change_page_attr() can fail which will cause set_memory_encrypted() and
set_memory_decrypted() to return non-zero.
If the device requires unencrypted DMA memory and decryption fails, simply
free the memory and fail.
If attempting to re-encrypt in the failure path and that encryption fails,
there is no alternative other than to leak the memory.
Fixes: c10f07aa27 ("dma/direct: Handle force decryption for DMA coherent buffers in common code")
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
If arch_dma_set_uncached() fails after memory has been decrypted, it needs
to be re-encrypted before freeing.
Fixes: fa7e2247c5 ("dma-direct: make uncached_kernel_address more general")
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
dma_alloc_contiguous() does size >> PAGE_SHIFT and set_memory_decrypted()
works at page granularity. It's necessary to page align the allocation
size in dma_direct_alloc_pages() for consistent behavior.
This also fixes an issue when arch_dma_prep_coherent() is called on an
unaligned allocation size for dma_alloc_need_uncached() when
CONFIG_DMA_DIRECT_REMAP is disabled but CONFIG_ARCH_HAS_DMA_SET_UNCACHED
is enabled.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
nommu configfs can trivially map the coherent allocations to user space,
as no actual page table setup is required and the kernel and the user
space programs share the same address space.
Fixes: 62fcee9a3b ("dma-mapping: remove CONFIG_ARCH_NO_COHERENT_DMA_MMAP")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: dillon min <dillon.minfei@gmail.com>
Reviewed-by: Vladimir Murzin <vladimir.murzin@arm.com>
Tested-by: dillon min <dillon.minfei@gmail.com>
Using _MASKED_BIT_ENABLE macro to set mask register bits is straight
forward and not likely to go wrong. However when checking which bit(s)
is(are) enabled, simply bitwise AND value and _MASKED_BIT_ENABLE() won't
output expected result. Suppose the register write is disabling bit 1
by setting 0xFFFF0000, however "& _MASKED_BIT_ENABLE(1)" outputs
0x00010000, and the non-zero check will pass which cause the old code
consider the new value set as an enabling operation.
We found guest set 0x80008000 on boot, and set 0xffff8000 during resume.
Both are legal settings but old code will block latter and force vgpu
enter fail-safe mode.
Introduce two new macro and make proper masked bit check in mmio handler:
IS_MASKED_BITS_ENABLED()
IS_MASKED_BITS_DISABLED()
V2: Rebase.
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20200601030721.17129-1-colin.xu@intel.com
Add flex_array_size() helper for the calculation of the size, in bytes,
of a flexible array member contained within an enclosing structure.
Example of usage:
struct something {
size_t count;
struct foo items[];
};
struct something *instance;
instance = kmalloc(struct_size(instance, items, count), GFP_KERNEL);
instance->count = count;
memcpy(instance->items, src, flex_array_size(instance, items, instance->count));
The helper returns SIZE_MAX on overflow instead of wrapping around.
Additionally replaces parameter "n" with "count" in struct_size() helper
for greater clarity and unification.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20200609012233.GA3371@embeddedor
Signed-off-by: Kees Cook <keescook@chromium.org>
cc-option and as-option are almost the same; both pass the flag to
$(CC). The main difference is the cc-option stops before the assemble
stage (-S option) whereas as-option stops after (-c option).
I chose -S because it is slightly faster, but $(cc-option,-gz=zlib)
returns a wrong result (https://lkml.org/lkml/2020/6/9/1529).
It has been fixed by commit 7b16994437 ("Makefile: Improve compressed
debug info support detection"), but the assembler should always be
invoked for more reliable compiler option tests.
However, you cannot simply replace -S with -c because the following
code in lib/Kconfig.debug would break:
depends on $(cc-option,-gsplit-dwarf)
The combination of -c and -gsplit-dwarf does not accept /dev/null as
output.
$ cat /dev/null | gcc -gsplit-dwarf -S -x c - -o /dev/null
$ echo $?
0
$ cat /dev/null | gcc -gsplit-dwarf -c -x c - -o /dev/null
objcopy: Warning: '/dev/null' is not an ordinary file
$ echo $?
1
$ cat /dev/null | gcc -gsplit-dwarf -c -x c - -o tmp.o
$ echo $?
0
There is another flag that creates an separate file based on the
object file path:
$ cat /dev/null | gcc -ftest-coverage -c -x c - -o /dev/null
<stdin>:1: error: cannot open /dev/null.gcno
So, we cannot use /dev/null to sink the output.
Align the cc-option implementation with scripts/Kbuild.include.
With -c option used in cc-option, as-option is unneeded.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Fix /proc/bootconfig to select double or single quotes
corrctly according to the value.
If a bootconfig value includes a double quote character,
we must use single-quotes to quote that value.
This modifies if() condition and blocks for avoiding
double-quote in value check in 2 places. Anyway, since
xbc_array_for_each_value() can handle the array which
has a single node correctly.
Thus,
if (vnode && xbc_node_is_array(vnode)) {
xbc_array_for_each_value(vnode) /* vnode->next != NULL */
...
} else {
snprintf(val); /* val is an empty string if !vnode */
}
is equivalent to
if (vnode) {
xbc_array_for_each_value(vnode) /* vnode->next can be NULL */
...
} else {
snprintf(""); /* value is always empty */
}
Link: http://lkml.kernel.org/r/159230244786.65555.3763894451251622488.stgit@devnote2
Cc: stable@vger.kernel.org
Fixes: c1a3c36017 ("proc: bootconfig: Add /proc/bootconfig to show boot config list")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
kmemleak report:
[<57dcc2ca>] __kmalloc_track_caller+0x139/0x2b0
[<f1c45d0f>] kstrndup+0x37/0x80
[<f9761eb0>] parse_probe_arg.isra.7+0x3cc/0x630
[<055bf2ba>] traceprobe_parse_probe_arg+0x2f5/0x810
[<655a7766>] trace_kprobe_create+0x2ca/0x950
[<4fc6a02a>] create_or_delete_trace_kprobe+0xf/0x30
[<6d1c8a52>] trace_run_command+0x67/0x80
[<be812cc0>] trace_parse_run_command+0xa7/0x140
[<aecfe401>] probes_write+0x10/0x20
[<2027641c>] __vfs_write+0x30/0x1e0
[<6a4aeee1>] vfs_write+0x96/0x1b0
[<3517fb7d>] ksys_write+0x53/0xc0
[<dad91db7>] __ia32_sys_write+0x15/0x20
[<da347f64>] do_syscall_32_irqs_on+0x3d/0x260
[<fd0b7e7d>] do_fast_syscall_32+0x39/0xb0
[<ea5ae810>] entry_SYSENTER_32+0xaf/0x102
Post parse_probe_arg(), the FETCH_OP_DATA operation type is overwritten
to FETCH_OP_ST_STRING, as a result memory is never freed since
traceprobe_free_probe_arg() iterates only over SYMBOL and DATA op types
Setup fetch string operation correctly after fetch_op_data operation.
Link: https://lkml.kernel.org/r/20200615143034.GA1734@cosmos
Cc: stable@vger.kernel.org
Fixes: a42e3c4de9 ("tracing/probe: Add immediate string parameter support")
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Vamshi K Sthambamkadi <vamshi.k.sthambamkadi@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
When using trace-cmd on 5.6-rt for the function graph tracer, the output was
corrupted. It gave output like this:
funcgraph_entry: func=0xffffffff depth=38982
funcgraph_entry: func=0x1ffffffff depth=16044
funcgraph_exit: func=0xffffffff overrun=0x92539aaf00000000 calltime=0x92539c9900000072 rettime=0x100000072 depth=11084
funcgraph_exit: func=0xffffffff overrun=0x9253946e00000000 calltime=0x92539e2100000072 rettime=0x72 depth=26033702
funcgraph_entry: func=0xffffffff depth=85798
funcgraph_entry: func=0x1ffffffff depth=12044
The reason was because the tracefs/events/ftrace/funcgraph_entry/exit format
file was incorrect. The -rt kernel adds more common fields to the trace
events. Namely, common_migrate_disable and common_preempt_lazy_count. Each
is one byte in size. This changes the alignment of the normal payload. Most
events are aligned normally, but the function and function graph events are
defined with a "PACKED" macro, that packs their payload. As the offsets
displayed in the format files are now calculated by an aligned field, the
aligned field for function and function graph events should be 1, not their
normal alignment.
With aligning of the funcgraph_entry event, the format file has:
field:unsigned short common_type; offset:0; size:2; signed:0;
field:unsigned char common_flags; offset:2; size:1; signed:0;
field:unsigned char common_preempt_count; offset:3; size:1; signed:0;
field:int common_pid; offset:4; size:4; signed:1;
field:unsigned char common_migrate_disable; offset:8; size:1; signed:0;
field:unsigned char common_preempt_lazy_count; offset:9; size:1; signed:0;
field:unsigned long func; offset:16; size:8; signed:0;
field:int depth; offset:24; size:4; signed:1;
But the actual alignment is:
field:unsigned short common_type; offset:0; size:2; signed:0;
field:unsigned char common_flags; offset:2; size:1; signed:0;
field:unsigned char common_preempt_count; offset:3; size:1; signed:0;
field:int common_pid; offset:4; size:4; signed:1;
field:unsigned char common_migrate_disable; offset:8; size:1; signed:0;
field:unsigned char common_preempt_lazy_count; offset:9; size:1; signed:0;
field:unsigned long func; offset:12; size:8; signed:0;
field:int depth; offset:20; size:4; signed:1;
Link: https://lkml.kernel.org/r/20200609220041.2a3b527f@oasis.local.home
Cc: stable@vger.kernel.org
Fixes: 04ae87a520 ("ftrace: Rework event_create_dir()")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
