Eric Dumazet says:
====================
tcp: remove two indirect calls from xmit path
__tcp_transmit_skb() does two indirect calls per packet, lets get rid
of them.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mitigate RETPOLINE costs in __tcp_transmit_skb()
by using INDIRECT_CALL_INET() wrapper.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mitigate RETPOLINE costs in __tcp_transmit_skb()
by using INDIRECT_CALL_INET() wrapper.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since iproute2 commit f72c3ad00f3b ("tc: m_tunnel_key: add options
support for vxlan"), the geneve opt output use key word "geneve_opts"
instead of "geneve_opt". To make compatibility for both old and new
iproute2, let's accept both "geneve_opt" and "geneve_opts".
Suggested-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Tested-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace assignment "=" with OR "|=" for "phy->dev_flags" so "dev_flags"
configured in phy probe() function can be preserved.
The idea is similar to commit e7312efbd5 ("net: phy: modify assignment
to OR for dev_flags in phy_attach_direct").
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Typically the firmware takes care that tp->ocp_base is reset to its
default value. That's not the case (at least) for RTL8117.
As a result subsequent PHY access reads/writes the wrong page and
the link is broken. Fix this be resetting tp->ocp_base explicitly.
Fixes: 229c1e0dfd ("r8169: load firmware for RTL8168fp/RTL8117")
Reported-by: Aaron Ma <mapengyu@gmail.com>
Tested-by: Aaron Ma <mapengyu@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be useful to allow busy poll for tunneled traffic. In case of
busy poll for sessions over tunnels, the underlying physical device's
queues need to be polled.
Tunnels schedule NAPI either via netif_rx() for backlog queue or
schedule the gro_cell_poll(). netif_rx() propagates the valid skb->napi_id
to the socket. OTOH, gro_cell_poll() stamps the skb->napi_id again by
calling skb_mark_napi_id() with the tunnel NAPI which is not a busy poll
candidate. This was preventing tunneled traffic to use busy poll. A valid
NAPI ID in the skb indicates it was already marked for busy poll by a
NAPI driver and hence needs to be copied into the socket.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
parent cannot be NULL here since its in the else part
of the if (parent == NULL) condition. Remove the extra
check on parent pointer.
Signed-off-by: Gaurav Singh <gaurav1086@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Continue the reset path when partner adapter is not ready or H_CLOSED is
returned from reset crq. This patch allows the CRQ init to proceed to
establish a valid CRQ for traffic to flow after reset.
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even with moving netif_tx_disable() to an earlier point when
taking down the queues for a reconfiguration, we still end
up with the occasional netdev watchdog Tx Timeout complaint.
The old method of using netif_trans_update() works fine for
queue 0, but has no effect on the remaining queues. Using
netif_device_detach() allows us to signal to the watchdog to
ignore us for the moment.
Fixes: beead698b1 ("ionic: Add the basic NDO callbacks for netdev support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
Ocelot/Felix driver cleanup
Some of the code in the mscc felix and ocelot drivers was added while in
a bit of a hurry. Let's take a moment and put things in relative order.
First 3 patches are sparse warning fixes.
Patches 4-9 perform some further splitting between mscc_felix,
mscc_ocelot, and the common hardware library they share. Meaning that
some code is being moved from the library into just the mscc_ocelot
module.
Patches 10-12 refactor the naming conventions in the existing VCAP code
(for tc-flower offload), since we're going to be adding some more code
for VCAP IS1 (previous tentatives already submitted here:
https://patchwork.ozlabs.org/project/netdev/cover/20200602051828.5734-1-xiaoliang.yang_1@nxp.com/),
and that code would be confusing to read and maintain using current
naming conventions.
No functional modification is intended. I checked that the VCAP IS2 code
still works by applying a tc ingress filter with an EtherType key and
'drop' action.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the function prototypes from ocelot_police.h and make these
functions static. We need to move them above their callers. Note that
moving the implementations to ocelot_police.c is not trivially possible
due to dependency on is2_entry_set() which is static to ocelot_vcap.c.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Access Control Lists (and their respective Access Control Entries) are
specifically entries in the VCAP IS2, the security enforcement block,
according to the documentation.
Let's rename the structures and functions to something more generic, so
that VCAP IS1 structures (which would otherwise have to be called
Ingress Classification Entries) can reuse the same code without
confusion.
Some renaming that was done:
struct ocelot_ace_rule -> struct ocelot_vcap_filter
struct ocelot_acl_block -> struct ocelot_vcap_block
enum ocelot_ace_type -> enum ocelot_vcap_key_type
struct ocelot_ace_vlan -> struct ocelot_vcap_key_vlan
enum ocelot_ace_action -> enum ocelot_vcap_action
struct ocelot_ace_stats -> struct ocelot_vcap_stats
enum ocelot_ace_type -> enum ocelot_vcap_key_type
struct ocelot_ace_frame_* -> struct ocelot_vcap_key_*
No functional change is intended.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Access Control Lists (and their respective Access Control Entries) are
specifically entries in the VCAP IS2, the security enforcement block,
according to the documentation.
Let's rename the files that deal with generic operations on the VCAP
TCAM, so that VCAP IS1 and ES0 can reuse the same code without
confusion.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot hardware library shouldn't contain too much net_device
specific code, since it is shared with DSA which abstracts that
structure away. So much as much of this code as possible into the
mscc_ocelot driver and outside of the common library.
We're making an exception for MDB and LAG code. That is not yet exported
to DSA, but when it will, most of the code that's already in ocelot.c
will remain there. So, there's no point in moving code to ocelot_net.c
just to move it back later.
We could have moved all net_device code to ocelot_vsc7514.c directly,
but let's operate under the assumption that if a new switchdev ocelot
driver gets added, it'll define its SoC-specific stuff in a new
ocelot_vsc*.c file and it'll reuse the rest of the code.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ocelot_regs.c actually shouldn't be part of the common library. It
describes the register map of the VSC7514 switch. The way ocelot
switches work, they'll have highly optimized register maps, so another
SoC will likely have the same registers but laid out completely
different in memory (so there's little room for reusing this structure).
So move it to ocelot_vsc7514.c instead.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Putting 'ocelot' in the config's name twice just to say that 'it's the
ocelot driver running on the ocelot SoC' is a bit confusing. Instead,
it's just the ocelot driver. Now that we've renamed the previous symbol
that was holding the MSCC_OCELOT_SWITCH_OCELOT into *_LIB (because
that's what it is), we're free to use this name for the driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hide the CONFIG_MSCC_OCELOT_SWITCH option from users. It is meant to be
only a hardware library which is selected by the drivers that use it
(ocelot, felix).
Since it is "selected" from Kconfig, all its dependencies are manually
transferred to the driver that selects it. This is because "select" in
Kconfig language is a bit of a mess, and doesn't handle dependencies of
selected options quite right.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mscc_ocelot is a slightly better name for a module than ocelot_board or
ocelot_vsc7514 is, so let's use that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To follow the model of felix and seville where we have one
platform-specific file, rename this file to the actual SoC it serves.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sparse is rightfully complaining about the fact that:
warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
26 | __builtin_constant_p((l) > (h)), (l) > (h), 0)))
| ^
note: in expansion of macro ‘GENMASK_INPUT_CHECK’
39 | (GENMASK_INPUT_CHECK(h, l) + __GENMASK(h, l))
| ^~~~~~~~~~~~~~~~~~~
note: in expansion of macro ‘GENMASK’
127 | mask = GENMASK(width, 0);
| ^~~~~~~
So replace the variables that go into GENMASK with plain, signed integer
types.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrea Mayer says:
====================
Strict mode for VRF
This patch set adds the new "strict mode" functionality to the Virtual
Routing and Forwarding infrastructure (VRF). Hereafter we discuss the
requirements and the main features of the "strict mode" for VRF.
On VRF creation, it is necessary to specify the associated routing table used
during the lookup operations. Currently, there is no mechanism that avoids
creating multiple VRFs sharing the same routing table. In other words, it is not
possible to force a one-to-one relationship between a specific VRF and the table
associated with it.
The "strict mode" imposes that each VRF can be associated to a routing table
only if such routing table is not already in use by any other VRF.
In particular, the strict mode ensures that:
1) given a specific routing table, the VRF (if exists) is uniquely identified;
2) given a specific VRF, the related table is not shared with any other VRF.
Constraints (1) and (2) force a one-to-one relationship between each VRF and the
corresponding routing table.
The strict mode feature is designed to be network-namespace aware and it can be
directly enabled/disabled acting on the "strict_mode" parameter.
Read and write operations are carried out through the classic sysctl command on
net.vrf.strict_mode path, i.e: sysctl -w net.vrf.strict_mode=1.
Only two distinct values {0,1} are accepted by the strict_mode parameter:
- with strict_mode=0, multiple VRFs can be associated with the same table.
This is the (legacy) default kernel behavior, the same that we experience
when the strict mode patch set is not applied;
- with strict_mode=1, the one-to-one relationship between the VRFs and the
associated tables is guaranteed. In this configuration, the creation of a VRF
which refers to a routing table already associated with another VRF fails and
the error is returned to the user.
The kernel keeps track of the associations between a VRF and the routing table
during the VRF setup, in the "management" plane. Therefore, the strict mode does
not impact the performance or the intrinsic functionality of the data plane in
any way.
When the strict mode is active it is always possible to disable the strict mode,
while the reverse operation is not always allowed.
Setting the strict_mode parameter to 0 is equivalent to removing the one-to-one
constraint between any single VRF and its associated routing table.
Conversely, if the strict mode is disabled and there are multiple VRFs that
refer to the same routing table, then it is prohibited to set the strict_mode
parameter to 1. In this configuration, any attempt to perform the operation will
lead to an error and it will be reported to the user.
To enable strict mode once again (by setting the strict_mode parameter to 1),
you must first remove all the VRFs that share common tables.
There are several use cases which can take advantage from the introduction of
the strict mode feature. In particular, the strict mode allows us to:
i) guarantee the proper functioning of some applications which deal with
routing protocols;
ii) perform some tunneling decap operations which require to use specific
routing tables for segregating and forwarding the traffic.
Considering (i), the creation of different VRFs that point to the same table
leads to the situation where two different routing entities believe they have
exclusive access to the same table. This leads to the situation where different
routing daemons can conflict for gaining routes control due to overlapping
tables. By enabling strict mode it is possible to prevent this situation which
often occurs due to incorrect configurations done by the users.
The ability to enable/disable the strict mode functionality does not depend on
the tool used for configuring the networking. In essence, the strict mode patch
solves, at the kernel level, what some other patches [1] had tried to solve at
the userspace level (using only iproute2) with all the related problems.
Considering (ii), the introduction of the strict mode functionality allows us
implementing the SRv6 End.DT4 behavior. Such behavior terminates a SR tunnel and
it forwards the IPv4 traffic according to the routes present in the routing
table supplied during the configuration. The SRv6 End.DT4 can be realized
exploiting the routing capabilities made available by the VRF infrastructure.
This behavior could leverage a specific VRF for forcing the traffic to be
forwarded in accordance with the routes available in the VRF table.
Anyway, in order to make the End.DT4 properly work, it must be guaranteed that
the table used for the route lookup operations is bound to one and only one VRF.
In this way, it is possible to use the table for uniquely retrieving the
associated VRF and for routing packets.
I would like to thank David Ahern for his constant and valuable support during
the design and development phases of this patch set.
Comments, suggestions and improvements are very welcome!
====================
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new strict mode functionality is tested in different configurations and
on different network namespaces.
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the initialization phase of the VRF module, the callback for table
to VRF device lookup is registered in l3mdev.
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add net.vrf.strict_mode sysctl parameter.
When net.vrf.strict_mode=0 (default) it is possible to associate multiple
VRF devices to the same table. Conversely, when net.vrf.strict_mode=1 a
table can be associated to a single VRF device.
When switching from net.vrf.strict_mode=0 to net.vrf.strict_mode=1, a check
is performed to verify that all tables have at most one VRF associated,
otherwise the switch is not allowed.
The net.vrf.strict_mode parameter is per network namespace.
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the data structures and the processing logic to keep track of the
associations between VRF devices and routing tables.
When a VRF is instantiated, it needs to refer to a given routing table.
For each table, we explicitly keep track of the existing VRFs that refer to
the table.
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add infrastructure to l3mdev (the core code for Layer 3 master devices) in
order to find out the corresponding VRF device for a given table id.
Therefore, the l3mdev implementations:
- can register a callback that returns the device index of the l3mdev
associated with a given table id;
- can offer the lookup function (table to VRF device).
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change STM32 pinctrl driver to not print an error trace when probe is
deferred due to clock resource. Probe defer issue (for clocks) could
occur during bank registering when some banks have already been registered.
In this case banks already registered should be released. To not waste time
in this case, it is better to check first if all clocks are available
before registering banks.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Link: https://lore.kernel.org/r/20200615125407.27632-2-alexandre.torgue@st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the correct the function name in the documentation for
"pcs_parse_one_pinctrl_entry()".
"smux_parse_one_pinctrl_entry()" appears to be an artifact from the
development of a prior patch series ("simple pinmux driver") which
transformed into pinctrl-single.
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Link: https://lore.kernel.org/r/20200612112758.GA3407886@x1
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull tracing fixes from Steven Rostedt:
- Have recordmcount work with > 64K sections (to support LTO)
- kprobe RCU fixes
- Correct a kprobe critical section with missing mutex
- Remove redundant arch_disarm_kprobe() call
- Fix lockup when kretprobe triggers within kprobe_flush_task()
- Fix memory leak in fetch_op_data operations
- Fix sleep in atomic in ftrace trace array sample code
- Free up memory on failure in sample trace array code
- Fix incorrect reporting of function_graph fields in format file
- Fix quote within quote parsing in bootconfig
- Fix return value of bootconfig tool
- Add testcases for bootconfig tool
- Fix maybe uninitialized warning in ftrace pid file code
- Remove unused variable in tracing_iter_reset()
- Fix some typos
* tag 'trace-v5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Fix maybe-uninitialized compiler warning
tools/bootconfig: Add testcase for show-command and quotes test
tools/bootconfig: Fix to return 0 if succeeded to show the bootconfig
tools/bootconfig: Fix to use correct quotes for value
proc/bootconfig: Fix to use correct quotes for value
tracing: Remove unused event variable in tracing_iter_reset
tracing/probe: Fix memleak in fetch_op_data operations
trace: Fix typo in allocate_ftrace_ops()'s comment
tracing: Make ftrace packed events have align of 1
sample-trace-array: Remove trace_array 'sample-instance'
sample-trace-array: Fix sleeping function called from invalid context
kretprobe: Prevent triggering kretprobe from within kprobe_flush_task
kprobes: Remove redundant arch_disarm_kprobe() call
kprobes: Fix to protect kick_kprobe_optimizer() by kprobe_mutex
kprobes: Use non RCU traversal APIs on kprobe_tables if possible
kprobes: Suppress the suspicious RCU warning on kprobes
recordmcount: support >64k sections
Pull libnvdimm updates from Dan Williams:
"A feature (papr_scm health retrieval) and a fix (sysfs attribute
visibility) for v5.8.
Vaibhav explains in the merge commit below why missing v5.8 would be
painful and I agreed to try a -rc2 pull because only cosmetics kept
this out of -rc1 and his initial versions were posted in more than
enough time for v5.8 consideration:
'These patches are tied to specific features that were committed to
customers in upcoming distros releases (RHEL and SLES) whose
time-lines are tied to 5.8 kernel release.
Being able to track the health of an nvdimm is critical for our
customers that are running workloads leveraging papr-scm nvdimms.
Missing the 5.8 kernel would mean missing the distro timelines and
shifting forward the availability of this feature in distro kernels
by at least 6 months'
Summary:
- Fix the visibility of the region 'align' attribute.
The new unit tests for region alignment handling caught a corner
case where the alignment cannot be specified if the region is
converted from static to dynamic provisioning at runtime.
- Add support for device health retrieval for the persistent memory
supported by the papr_scm driver.
This includes both the standard sysfs "health flags" that the nfit
persistent memory driver publishes and a mechanism for the ndctl
tool to retrieve a health-command payload"
* tag 'libnvdimm-for-5.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nvdimm/region: always show the 'align' attribute
powerpc/papr_scm: Implement support for PAPR_PDSM_HEALTH
ndctl/papr_scm,uapi: Add support for PAPR nvdimm specific methods
powerpc/papr_scm: Improve error logging and handling papr_scm_ndctl()
powerpc/papr_scm: Fetch nvdimm health information from PHYP
seq_buf: Export seq_buf_printf
powerpc: Document details on H_SCM_HEALTH hcall
This reverts commit ba40324261.
After commit 26d8cde526 ("pinctrl: freescale: imx: add shared
input select reg support"). i.MX7D has two iomux controllers
iomuxc and iomuxc-lpsr which share select_input register for
daisy chain settings.
If use 'devm_of_iomap()', when probe the iomuxc-lpsr, will call
devm_request_mem_region() for the region <0x30330000-0x3033ffff>
for the first time. Then, next time when probe the iomuxc, API
devm_platform_ioremap_resource() will also use the API
devm_request_mem_region() for the share region <0x30330000-0x3033ffff>
again, then cause issue, log like below:
[ 0.179561] imx7d-pinctrl 302c0000.iomuxc-lpsr: initialized IMX pinctrl driver
[ 0.191742] imx7d-pinctrl 30330000.pinctrl: can't request region for resource [mem 0x30330000-0x3033ffff]
[ 0.191842] imx7d-pinctrl: probe of 30330000.pinctrl failed with error -16
Fixes: ba40324261 ("pinctrl: freescale: imx: Use 'devm_of_iomap()' to avoid a resource leak in case of error in 'imx_pinctrl_probe()'")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Link: https://lore.kernel.org/r/1591673223-1680-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull s390 fixes from Vasily Gorbik:
- a few ptrace fixes mostly for strace and seccomp_bpf kernel tests
findings
- cleanup unused pm callbacks in virtio ccw
- replace kmalloc + memset with kzalloc in crypto
- use $(LD) for vDSO linkage to make clang happy
- fix vDSO clock_getres() to preserve the same behaviour as
posix_get_hrtimer_res()
- fix workqueue cpumask warning when NUMA=n and nr_node_ids=2
- reduce SLSB writes during input processing, improve warnings and
cleanup qdio_data usage in qdio
- a few fixes to use scnprintf() instead of snprintf()
* tag 's390-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: fix syscall_get_error for compat processes
s390/qdio: warn about unexpected SLSB states
s390/qdio: clean up usage of qdio_data
s390/numa: let NODES_SHIFT depend on NEED_MULTIPLE_NODES
s390/vdso: fix vDSO clock_getres()
s390/vdso: Use $(LD) instead of $(CC) to link vDSO
s390/protvirt: use scnprintf() instead of snprintf()
s390: use scnprintf() in sys_##_prefix##_##_name##_show
s390/crypto: use scnprintf() instead of snprintf()
s390/zcrypt: use kzalloc
s390/virtio: remove unused pm callbacks
s390/qdio: reduce SLSB writes during Input Queue processing
selftests/seccomp: s390 shares the syscall and return value register
s390/ptrace: fix setting syscall number
s390/ptrace: pass invalid syscall numbers to tracing
s390/ptrace: return -ENOSYS when invalid syscall is supplied
s390/seccomp: pass syscall arguments via seccomp_data
s390/qdio: fine-tune SLSB update
Pull RISC-V fixes from Palmer Dabbelt:
- a workaround for a compiler surprise related to the "r" inline
assembly that allows LLVM to boot.
- a fix to avoid WX-only mappings, which the ISA does not allow. While
this probably manifests in many ways, the bug was found in stress-ng.
- a missing lock in set_direct_map_*(), which due to a recent lockdep
change started asserting.
* tag 'riscv-for-linus-5.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
RISC-V: Acquire mmap lock before invoking walk_page_range
RISC-V: Don't allow write+exec only page mapping request in mmap
riscv/atomic: Fix sign extension for RV64I
