The pins on the Bay Trail SoC have separate input-buffer and output-buffer
enable bits and a read of the level bit of the value register will always
return the value from the input-buffer.
The BIOS of a device may configure a pin in output-only mode, only enabling
the output buffer, and write 1 to the level bit to drive the pin high.
This 1 written to the level bit will be stored inside the data-latch of the
output buffer.
But a subsequent read of the value register will return 0 for the level bit
because the input-buffer is disabled. This causes a read-modify-write as
done by byt_gpio_set_direction() to write 0 to the level bit, driving the
pin low!
Before this commit byt_gpio_direction_output() relied on
pinctrl_gpio_direction_output() to set the direction, followed by a call
to byt_gpio_set() to apply the selected value. This causes the pin to
go low between the pinctrl_gpio_direction_output() and byt_gpio_set()
calls.
Change byt_gpio_direction_output() to directly make the register
modifications itself instead. Replacing the 2 subsequent writes to the
value register with a single write.
Note that the pinctrl code does not keep track internally of the direction,
so not going through pinctrl_gpio_direction_output() is not an issue.
This issue was noticed on a Trekstor SurfTab Twin 10.1. When the panel is
already on at boot (no external monitor connected), then the i915 driver
does a gpiod_get(..., GPIOD_OUT_HIGH) for the panel-enable GPIO. The
temporarily going low of that GPIO was causing the panel to reset itself
after which it would not show an image until it was turned off and back on
again (until a full modeset was done on it). This commit fixes this.
This commit also updates the byt_gpio_direction_input() to use direct
register accesses instead of going through pinctrl_gpio_direction_input(),
to keep it consistent with byt_gpio_direction_output().
Note for backporting, this commit depends on:
commit e2b74419e5 ("pinctrl: baytrail: Replace WARN with dev_info_once
when setting direct-irq pin to output")
Cc: stable@vger.kernel.org
Fixes: 86e3ef812f ("pinctrl: baytrail: Update gpio chip operations")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We currently decide to execute the PtrAuth save/restore code based
on a set of branches that evaluate as (ARM64_HAS_ADDRESS_AUTH_ARCH ||
ARM64_HAS_ADDRESS_AUTH_IMP_DEF). This can be easily replaced by
a much simpler test as the ARM64_HAS_ADDRESS_AUTH capability is
exactly this expression.
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
When save/restoring PtrAuth registers between host and guest, it is
pretty useless to fetch the in-memory state, while we have the right
state in the HCR_EL2 system register. Use that instead.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Now that the scene is set for enabling PtrAuth on non-VHE, drop
the restrictions preventing userspace from enabling it.
Acked-by: Andrew Scull <ascull@google.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
We currently prevent PtrAuth from even being built if KVM is selected,
but VHE isn't. It is a bit of a pointless restriction, since we also
check this at run time (rejecting the enabling of PtrAuth for the
vcpu if we're not running with VHE).
Just drop this apparently useless restriction.
Acked-by: Andrew Scull <ascull@google.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
While initializing EL2, enable Address Authentication if detected
from EL1. We still use the EL1-provided keys though.
Acked-by: Andrew Scull <ascull@google.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Building the current 5.8 kernel for an e500 machine with
CONFIG_RANDOMIZE_BASE=y and CONFIG_BLOCK=n yields the following
failure:
arch/powerpc/mm/nohash/kaslr_booke.c: In function 'kaslr_early_init':
arch/powerpc/mm/nohash/kaslr_booke.c:387:2: error: implicit
declaration of function 'flush_icache_range'; did you mean 'flush_tlb_range'?
Indeed, including asm/cacheflush.h into kaslr_booke.c fixes the build.
Fixes: 2b0e86cc5d ("powerpc/fsl_booke/32: implement KASLR infrastructure")
Cc: stable@vger.kernel.org # v5.5+
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Acked-by: Scott Wood <oss@buserror.net>
[mpe: Tweak change log to mention CONFIG_BLOCK=n]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200613162801.1946619-1-asolokha@kb.kras.ru
With hash translation, the hypervisor can hint the LPAR about 16GB contiguous range
via ibm,expected#pages. The kernel marks the range specified in the device tree
as reserved. Avoid doing this when using radix translation. Radix translation
only supports 1G gigantic hugepage and kernel can do the 1G gigantic hugepage
allocation via early memblock reservation. This can be done because with radix
translation pages are not required to be contiguous on the host.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200622064019.16682-1-aneesh.kumar@linux.ibm.com
Right now the driver uses only 3 LED modes:
0: On
1: HW Blinking (Interval 1)
3: Off
However, the controller supports a second HW blinking interval, which results
in 4 possible LED modes:
0: On
1: HW Blinking (Interval 1)
2: HW Blinking (Interval 2)
3: Off
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Drop the pointless and needlessly confusing casts of struct-device
pointers.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Several MFD child drivers register their class devices directly under
the parent device. This means you cannot blindly do devres conversions
so that deregistration ends up being tied to the parent device,
something which leads to use-after-free on driver unbind when the class
device is released while still being registered.
Fixes: 8d3b6a4001 ("leds: wm831x-status: Use devm_led_classdev_register")
Cc: stable <stable@vger.kernel.org> # 4.6
Cc: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Several MFD child drivers register their class devices directly under
the parent device. This means you cannot use devres so that
deregistration ends up being tied to the parent device, something which
leads to use-after-free on driver unbind when the class device is
released while still being registered.
Fixes: 11e1bbc116 ("leds: lm36274: Introduce the TI LM36274 LED driver")
Cc: stable <stable@vger.kernel.org> # 5.3
Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Several MFD child drivers register their class devices directly under
the parent device. This means you cannot blindly do devres conversions
so that deregistration ends up being tied to the parent device,
something which leads to use-after-free on driver unbind when the class
device is released while still being registered.
Fixes: 50154e29e5 ("leds: lm3533: Use devm_led_classdev_register")
Cc: stable <stable@vger.kernel.org> # 4.6
Cc: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Several MFD child drivers register their class devices directly under
the parent device. This means you cannot blindly do devres conversions
so that deregistration ends up being tied to the parent device,
something which leads to use-after-free on driver unbind when the class
device is released while still being registered.
Fixes: eed16255d6 ("leds: da903x: Use devm_led_classdev_register")
Cc: stable <stable@vger.kernel.org> # 4.6
Cc: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Several MFD child drivers register their class devices directly under
the parent device. This means you cannot blindly do devres conversions
so that deregistration ends up being tied to the parent device,
something which leads to use-after-free on driver unbind when the class
device is released while still being registered.
Fixes: 375446df95 ("leds: 88pm860x: Use devm_led_classdev_register")
Cc: stable <stable@vger.kernel.org> # 4.6
Cc: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
clang points out that doing arithmetic between diffent enums is usually
a mistake:
drivers/leds/leds-lm355x.c:167:28: warning: bitwise operation between different enumeration types ('enum lm355x_tx2' and 'enum lm355x_ntc') [-Wenum-enum-conversion]
reg_val = pdata->pin_tx2 | pdata->ntc_pin;
~~~~~~~~~~~~~~ ^ ~~~~~~~~~~~~~~
drivers/leds/leds-lm355x.c:178:28: warning: bitwise operation between different enumeration types ('enum lm355x_tx2' and 'enum lm355x_ntc') [-Wenum-enum-conversion]
reg_val = pdata->pin_tx2 | pdata->ntc_pin | pdata->pass_mode;
~~~~~~~~~~~~~~ ^ ~~~~~~~~~~~~~~
In this driver, it is intentional, so add a cast to hide the false-positive
warning. It appears to be the only instance of this warning at the moment.
Fixes: b98d13c725 ("leds: Add new LED driver for lm355x chips")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
The documentation reports the wrong macro names
related to the pca9532 instead of the pca955x
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Protect IO in intel_gpio_get_direction(), intel_gpio_community_irq_handler(),
intel_config_get_debounce() and intel_config_get_pull() by lock. Even for
simple readl() we better serialize IO to avoid potential problems.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Split intel_config_get() to three functions, i.e. intel_config_get() and
two helpers intel_config_get_pull() and intel_config_get_debounce() to be
symmetrical with intel_config_set*().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Drop the only label in the code, i.e. in intel_config_set_debounce(),
for consistency with the rest. In entire driver we use multipoint
return.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Instead of using bitwise operations against returned values,
which is a bit fragile, convert IRQ handler to count amount of
GPIO groups, where at least one interrupt happened, and convert
it to returned value by IRQ_RETVAL() macro.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
It's possible scenario that pin has been in different mode, while
the respective GPIO register has a leftover output buffer enabled.
In such case when we request GPIO it will switch to GPIO mode, and
thus to output with unknown value, followed by switching to input
mode. This can produce a glitch on the pin.
Disable input and output buffer when switching to GPIO to avoid
potential glitches.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We have some data structures duplicated across the drivers.
Let's deduplicate them by using struct intel_pinctrl_soc_data,
struct intel_community and struct intel_pinctrl_context that
are being provided by pinctrl-intel.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Individual drivers may install ACPI OpRegion handlers based on
address space ID which differs from community to community.
Add special field in the struct intel_community for that purpose.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
According to the latest AM65x Data Manual[1], a different output tap
delay value is optimum for a given speed mode. Update these values.
[1] http://www.ti.com/lit/gpn/am6526
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
