The SDHCI on Tegra30 is in fact not backwards-compatible with the
instantiation found on earlier SoCs. Drop the misleading compatible
string.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The display controller on Tegra30 is in fact not backwards-compatible
with the instantiation found on earlier SoCs. Drop the misleading
compatible string.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DSI output needs to specify a parent clock that will be used to
drive both the output and the display controller.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Seaboard uses a non-existing, possibly obsoleted, binding for the
battery. Move to the standard binding which seems to be a super-
set of the odl binding.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Unit-addresses should be numeric. This fixes a validation failure seen
using the json-schema tooling.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Simple panels can only have a single power supply. The second listed
supply is not needed because it is also the input supply of the first
supply and therefore will always be on at the same time.
In retrospect the panel probably doesn't qualify as simple since it
apparently does need both of these supplies, even if in the case of the
Medcom Wide it isn't necessary to explicitly hook them up.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use commas rather than underscores to separate the various parts of the
unit-address in CPU OPPs to make them properly validate under the json-
schema bindings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This is purely to make the json-schema validation tools happy because
they cannot deal with string arrays that may be in arbitrary order.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The memory controller exposes a set of memory client resets and needs to
specify the #reset-cells property in order to advertise the number of
cells needed to describe each of the resets.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tuple boundaries should be marked by < and > to make it clear which
cells are part of the same tuple. This also helps the json-schema based
validation tooling to properly parse this data.
While at it, also remove the "immovable" bit from PCI addresses. All of
these addresses are in fact "movable".
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SDHCI controller instantiated on Tegra114 is not backwards-
compatible with the version on Tegra30, so remove the corresponding
compatible string.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The parent clocks are determined by the output that will be used, not by
the display controller that drives the output. On previous generations a
simple RGB output used to be part of the display controller and hence an
explicit parent clock needed to be assigned to the display controller to
drive the RGB output. Starting with Tegra124, that RGB output has been
dropped and the parent clock can therefore be removed from the display
controller device tree nodes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
SC27XX-SPI added subdevices according to a pre-defined mfd_cell array,
no matter these devices were really included on board. In this patch,
switch to use devm_of_platform_populate() for adding sub-devices which
are defined in devicetree.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the Thermal driver along the MFD drivers and header as Maintained
by myself.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The new Khadas VIM2 and VIM3 boards controls the cooling fan via the
on-board microcontroller.
This implements the FAN control as thermal devices and as cell of the Khadas
MCU MFD driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Flow metering entries in IEEE 802.1Qci is an optional function for a
flow filtering module. Flow metering is two rates two buckets and three
color marker to policing the frames. This patch only enable one rate one
bucket and in color blind mode. Flow metering instance are as
specified in the algorithm in MEF 10.3 and in Bandwidth Profile
Parameters. They are:
a) Flow meter instance identifier. An integer value identifying the flow
meter instance. The patch use the police 'index' as thin value.
b) Committed Information Rate (CIR), in bits per second. This patch use
the 'rate_bytes_ps' represent this value.
c) Committed Burst Size (CBS), in octets. This patch use the 'burst'
represent this value.
d) Excess Information Rate (EIR), in bits per second.
e) Excess Burst Size per Bandwidth Profile Flow (EBS), in octets.
And plus some other parameters. This patch set EIR/EBS default disable
and color blind mode.
v1->v2 changes:
- Use div_u64() as division replace the '/' report:
All errors (new ones prefixed by >>):
ld: drivers/net/ethernet/freescale/enetc/enetc_qos.o: in function `enetc_flowmeter_hw_set':
>> enetc_qos.c:(.text+0x66): undefined reference to `__udivdi3'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware device may include more than one police entry. Specifying the
action's index make it possible for several tc filters to share the same
police action when installing the filters.
Propagate this index to device drivers through the flow offload
intermediate representation, so that drivers could share a single
hardware policer between multiple filters.
v1->v2 changes:
- Update the commit message suggest by Ido Schimmel <idosch@idosch.org>
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Base on the tc flower offload police action add max frame size by the
parameter 'mtu'. Tc flower device driver working by the IEEE 802.1Qci
stream filter can implement the max frame size filtering. Add it to the
current hardware tc flower stearm filter driver.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current police offloading support the 'burst'' and 'rate_bytes_ps'. Some
hardware own the capability to limit the frame size. If the frame size
larger than the setting, the frame would be dropped. For the police
action itself already accept the 'mtu' parameter in tc command. But not
extend to tc flower offloading. So extend 'mtu' to tc flower offloading.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Doug Berger says:
====================
net: bcmgenet: use hardware padding of runt frames
Now that scatter-gather and tx-checksumming are enabled by default
it revealed a packet corruption issue that can occur for very short
fragmented packets.
When padding these frames to the minimum length it is possible for
the non-linear (fragment) data to be added to the end of the linear
header in an SKB. Since the number of fragments is read before the
padding and used afterward without reloading, the fragment that
should have been consumed can be tacked on in place of part of the
padding.
The third commit in this set corrects this by removing the software
padding and allowing the hardware to add the pad bytes if necessary.
The first two commits resolve warnings observed by the kbuild test
robot and are included here for simplicity of application.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When commit 474ea9cafc ("net: bcmgenet: correctly pad short
packets") added the call to skb_padto() it should have been
located before the nr_frags parameter was read since that value
could be changed when padding packets with lengths between 55
and 59 bytes (inclusive).
The use of a stale nr_frags value can cause corruption of the
pad data when tx-scatter-gather is enabled. This corruption of
the pad can cause invalid checksum computation when hardware
offload of tx-checksum is also enabled.
Since the original reason for the padding was corrected by
commit 7dd399130e ("net: bcmgenet: fix skb_len in
bcmgenet_xmit_single()") we can remove the software padding all
together and make use of hardware padding of short frames as
long as the hardware also always appends the FCS value to the
frame.
Fixes: 474ea9cafc ("net: bcmgenet: correctly pad short packets")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 16-bit value that holds a short in network byte order should
be declared as a restricted big endian type to allow type checks
to succeed during assignment.
Fixes: 3e37095228 ("net: bcmgenet: add support for ethtool rxnfc flows")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function was originally removed by Baoyou Xie in
commit e2072600a2 ("net: bcmgenet: remove unused function in
bcmgenet.c") to prevent a build warning.
Some of the functions removed by Baoyou Xie are now used for
WAKE_FILTER support so his commit was reverted, but this function
is still unused and the kbuild test robot dutifully reported the
warning.
This commit once again removes the remaining unused hfb functions.
Fixes: 14da1510fe ("Revert "net: bcmgenet: remove unused function in bcmgenet.c"")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is code for adjusting the clock both in setup_fifo_params()
(called from prepare_message()) and in setup_fifo_xfer() (called from
transfer_one()). The code is the same. Abstract it out to a shared
function.
This is a no-op cleanup patch. The only change is to the error string
if we fail to set the clock. Since the two paths has marginally
different error messages I picked the clean one.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Link: https://lore.kernel.org/r/1592908737-7068-6-git-send-email-akashast@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
QUP core clock is shared among all the SE drivers present on particular
QUP wrapper, the system will reset(unclocked access) if earlycon used after
QUP core clock is put to 0 from other SE drivers before real console comes
up.
As earlycon can't vote for it's QUP core need, to fix this add ICC
support to common/QUP wrapper driver and put vote for QUP core from
probe on behalf of earlycon and remove vote during earlycon exit call.
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Reported-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1592908737-7068-3-git-send-email-akashast@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Yonghong Song says:
====================
bpf iterator implments traversal of kernel data structures and these
data structures are passed to a bpf program for processing.
This gives great flexibility for users to examine kernel data
structure without using e.g. /proc/net which has limited and
fixed format.
Commit 138d0be35b ("net: bpf: Add netlink and ipv6_route bpf_iter targets")
implemented bpf iterators for netlink and ipv6_route.
This patch set intends to implement bpf iterators for tcp and udp.
Currently, /proc/net/tcp is used to print tcp4 stats and /proc/net/tcp6
is used to print tcp6 stats. /proc/net/udp[6] have similar usage model.
In contrast, only one tcp iterator is implemented and it is bpf program
resposibility to filter based on socket family. The same is for udp.
This will avoid another unnecessary traversal pass if users want
to check both tcp4 and tcp6.
Several helpers are also implemented in this patch
bpf_skc_to_{tcp, tcp6, tcp_timewait, tcp_request, udp6}_sock
The argument for these helpers is not a fixed btf_id. For example,
bpf_skc_to_tcp(struct sock_common *), or
bpf_skc_to_tcp(struct sock *), or
bpf_skc_to_tcp(struct inet_sock *), ...
are all valid. At runtime, the helper will check whether pointer cast
is legal or not. Please see Patch #5 for details.
Since btf_id's for both arguments and return value are known at
build time, the btf_id's are pre-computed once vmlinux btf becomes
valid. Jiri's "adding d_path helper" patch set
https://lore.kernel.org/bpf/20200616100512.2168860-1-jolsa@kernel.org/T/
provides a way to pre-compute btf id during vmlinux build time.
This can be applied here as well. A followup patch can convert
to build time btf id computation after Jiri's patch landed.
Changelogs:
v4 -> v5:
- fix bpf_skc_to_udp6_sock helper as besides sk_protocol, sk_family,
sk_type == SOCK_DGRAM is also needed to differentiate from
SOCK_RAW (Eric)
v3 -> v4:
- fix bpf_skc_to_{tcp_timewait, tcp_request}_sock helper implementation
as just checking sk->sk_state is not enough (Martin)
- fix a few kernel test robot reported failures
- move bpf_tracing_net.h from libbpf to selftests (Andrii)
- remove __weak attribute from selftests CONFIG_HZ variables (Andrii)
v2 -> v3:
- change sock_cast*/SOCK_CAST* names to btf_sock* names for generality (Martin)
- change gpl_license to false (Martin)
- fix helper to cast to tcp timewait/request socket. (Martin)
v1 -> v2:
- guard init_sock_cast_types() defination properly with CONFIG_NET (Martin)
- reuse the btf_ids, computed for new helper argument, for return
values (Martin)
- using BTF_TYPE_EMIT to express intent of btf type generation (Andrii)
- abstract out common net macros into bpf_tracing_net.h (Andrii)
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
