The VXLAN neigh_reduce() code is completely non-functional since
check-in. Specific errors:
1) The original code drops all packets with a multicast destination address,
even though neighbor solicitations are sent to the solicited-node
address, a multicast address. The code after this check was never run.
2) The neighbor table lookup used the IPv6 header destination, which is the
solicited node address, rather than the target address from the
neighbor solicitation. So neighbor lookups would always fail if it
got this far. Also for L3MISSes.
3) The code calls ndisc_send_na(), which does a send on the tunnel device.
The context for neigh_reduce() is the transmit path, vxlan_xmit(),
where the host or a bridge-attached neighbor is trying to transmit
a neighbor solicitation. To respond to it, the tunnel endpoint needs
to do a *receive* of the appropriate neighbor advertisement. Doing a
send, would only try to send the advertisement, encapsulated, to the
remote destinations in the fdb -- hosts that definitely did not do the
corresponding solicitation.
4) The code uses the tunnel endpoint IPv6 forwarding flag to determine the
isrouter flag in the advertisement. This has nothing to do with whether
or not the target is a router, and generally won't be set since the
tunnel endpoint is bridging, not routing, traffic.
The patch below creates a proxy neighbor advertisement to respond to
neighbor solicitions as intended, providing proper IPv6 support for neighbor
reduction.
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an error occurs during the initialization in emac_dev_open() (the
driver's ndo_open function), interrupts, DMA descriptors etc. must be freed.
The current rollback code is buggy in several ways.
1) Freeing the interrupts. The current code will not free all interrupts
that were requested by the driver. Furthermore, the code tries to do a
platform_get_resource(priv->pdev, IORESOURCE_IRQ, -1) in its last
iteration.
This patch fixes these bugs.
2) Wrong order of err: and rollback: labels. If the setup of the PHY in
the code fails, the interrupts that have been requested before are
not freed:
request irq
if requesting irqs fails, goto rollback
setup phy
if phy setup fails, goto err
return 0
rollback:
free irqs
err:
This patch brings the code into the correct order.
3) The code calls napi_enable() and emac_int_enable(), but does not
undo both in case of an error.
This patch adds calls of emac_int_disable() and napi_disable() to the
rollback code.
4) RX DMA descriptors are not freed in case of an error: Right before
requesting the irqs, the function creates DMA descriptors for the
RX channel. These RX descriptors are never freed when we jump to either
rollback or err.
This patch adds code for freeing the DMA descriptors in the case of
an initialization error. This required a modification of
cpdma_ctrl_stop() in davinci_cpdma.c: We must be able to call this
function to free the DMA descriptors while the DMA channels are
in IDLE state (before cpdma_ctlr_start() was called).
Tested on a custom board with the Texas Instruments AM1808.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 6892b41d97
Author: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Date: Tue Jun 25 21:24:51 2013 +0530
net: davinci: emac: Convert to devm_* api
the call of request_irq is replaced by devm_request_irq and the call
of free_irq is removed. But since interrupts are requested in
emac_dev_open, doing ifconfig up/down on the board requests the
interrupts again each time, causing devm_request_irq to fail. The
interface is dead until the device is rebooted.
This patch reverts said commit partially: It changes the driver back
to use request_irq instead of devm_request_irq, puts free_irq back in
place, but keeps the remaining changes of the original patch.
Reported-by: Jon Ringle <jon@ringle.org>
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to igb, ixgbe, ixgbevf, i40e and i40evf.
Anjali provides a i40e/i40evf patch to add Energy Efficient Ethernet
Low Power Idle stats and a fix for i40e to change the string
"Side Band" to "Sideband" for consistency.
Mitch provides 2 patches for i40evf to fix if the driver encounters
an error while communicating with the PF driver, do not shut down the
admin queue unconditionally. Add an error message when the admin
queue message never completes and fix formatting on another message
that was unnecessarily wrapped.
Mark provides a ixgbe patch and five ixgbevf patches. Fix a possible
infinite recursion when an adapter is removed and registers all read
as all one's in ixgbe_clear_vmdq_generic() and ixgbe_clear_rar_generic().
Converts macros to static inline functions to align kernel coding standard
and prepare for adding Live Error Recovery (LER) to ixgbevf. Change the
ethtool register test to use the normal register accessor functions and
eliminate macors used for calling register test functions to make error
exits more clear. Checks all register reads for adapter removal by checking
the status register after any register read that returns all F's since the
status register will never return 0xFFFFFFFF unless the adapter is removed.
Jacob implements SIOCGHWTSTAMP ioctl for igb which enables user processes
to read the current hardware stamp config settings non-destructively.
Todd adds the initial register read and write for surprise removal (LER)
for igb.
Christian Engelmayer fixes an igb memory leak in the igb_get_module_eeprom()
error handling path.
Ken Ichikawa provides a fix for igb, specifically for 82575 hardware to
specify -1 to the phc_index for ethtool's get_ts_info, otherwise a wrong
value will be set to the phc_index.
Christopher Paasch fixes a null pointer dereference in igb and makes sure
to unset the HAS_MSIX flag when the driver falls back to MSI only.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As commit a6e28b34205b("staging/et131x: use SET_ETHTOOL_OPS
directly"), using a wrapper around SET_ETHTOOL_OPS macro is
not actually required, remove and use SET_ETHTOOL_OPS directly.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses two typos in the original driver submission. One derived
from a cut & paste error, and another is a misspelling.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses a portable pointer arithmetic issue in the
original submission found by the kbuild test robot.
config: make ARCH=i386 allyesconfig
altera_sgdma.c: In function 'sgdma_txphysaddr':
>> altera_sgdma.c:393:33: warning: cast from
>> pointer to integer of different size [-Wpointer-to-int-cast]
dma_addr_t offs = (dma_addr_t)((dma_addr_t)desc -
^
>> altera_sgdma.c:394:5: warning: cast from
>> pointer to integer of different size [-Wpointer-to-int-cast]
(dma_addr_t)priv->tx_dma_desc);
^
altera_sgdma.c: In function 'sgdma_rxphysaddr':
>> altera_sgdma.c:403:33: warning: cast from
>> pointer to integer of different size [-Wpointer-to-int-cast]
dma_addr_t offs = (dma_addr_t)((dma_addr_t)desc -
^
>> altera_sgdma.c:404:5: warning: cast from
>> pointer to integer of different size [-Wpointer-to-int-cast]
(dma_addr_t)priv->rx_dma_desc);
^
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the version number returned by the driver's get regs routine
invoked by ethtool so formatting can be dependent on the version
number returned, and any interesting formatted output can check
the version number for specific types of register data returned.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the macro to convert the MAC address from WMI word
format to char array has lead to the wrong peer mac
address printed out while retrieving the peer stats from
FW. Fix this.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Reviewed-By: Michał Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Regulatory domain settings for firmware 10.x has more options
than main firmware, so handle regulatory domain setup separately
for both supported firmwares. Fill in additional dfs domain
parameter according to current regulatory.
This patch does not solve any known bug. Not handled parameter
for firmware 10.x was found during code review.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Command WMI_FORCE_FW_HANG_CMDID is not supported in firmware 10.1.
In order to have firmware crash simulation functionality also
in firmware 10.1 driver can force firmware crash by performing not allowed
operation. Driver can deliberately crash firmware when setting vdev param for
vdev id out of range. This patch introduces two keywords to simulate_fw_crash:
'soft' which will cause firmware crash that is recoverable
by warm firmware reset but supported only in main firmware.
'hard' which will cause firmware crash recoverable by cold
firmware reset, this option works for both firmwares.
Commands to trigger firmware soft/hard crash:
echo 'soft' > /sys/kernel/debug/ieee80211/phyX/ath10k/simulate_fw_crash
echo 'hard' > /sys/kernel/debug/ieee80211/phyX/ath10k/simulate_fw_crash
kvalo: remove '\n' before checking the command and simplify how buf is null
terminated
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds Rx checksum offload support for VXLAN.
Implements .ndo_{add|del}_vxlan_port netdev ops.
Adapter supports only one VXLAN port, so program adapter with
very first UDP port which VXLAN driver is listening to.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds LSO, LSO6 and Tx checksum offload support for VXLAN
encapsulated packets on 83xx/84xx series adapters.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The P1010 device tree restricts the number of
supported interrupt groups to 1, although the eth
controller can support 2 interrupt groups and the
driver assumes the Multi-Group mode ("fsl,etsec2" model).
So, in this case the assumption that the Multi-Group
mode (MQ_MG_MODE) devices always support 2 interrupt
groups is false. To fix this, a check for the actual
number of interrupt groups enabled in the board's
device tree has been added in gfar_probe for the
"fsl,etsec2" devices.
Without this fix, P1010 based boards claim support for
2 Tx queues to the net stack but only one is actually
allocated, leading to NULL access in xmit. This issue
was introduced by enabling Single-Queue polling for
the P1010 devices.
(71ff9e3 gianfar: Use Single-Queue polling for
"fsl,etsec2")
Fixes: 71ff9e3df7
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Few platforms use external regulator to keep the ethernet MAC supplied.
So, request and enable the regulator for driver functionality.
Fixes: 66fda75f47 (regulator: core: Replace direct ops->disable usage)
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Suggested-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver use the new pin configuration method when
programming the periodic output signal.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver to use the new pin configuration method when
programming the external time stamp input signals.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adapts the dp83640 driver to allow reconfiguration of which
auxiliary function goes on which pin. The functions may be reassigned
freely with the one exception of the calibration function.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phyter driver incorrectly feeds the value of the period into what
is in fact a pulse width register, resulting in the actual period
being twice the dialed value. This patch fixes the issue and renames a
variable to make the code at bit more clear.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up the input checking code on the external time stamp
function by using an unsigned rather than a signed channel index.
Also, this patch corrects the author's email address. When this macro
was last changed, the top level domain part of the email address was
left behind.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the many PTP Hardware Clock drivers with the
newly introduced field that advertises the number of programmable
pins. Some of these devices do have programmable pins, but the
implementation will have to wait for follow on patches.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce ath10k_htt_rx_amsdu_allowed() function, that
group code for checking if skip amsdu packets.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When we execute otp.bin in the target check that the result it returns doesn't
contain an error. This is to make sure that we don't accidentally use invalid
calibration data.
While at it, remove the useless label in the function and add few debug messages.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's just cleaner to have separate argument for the parameter and result. Also
fix returned error value if response length is invalid.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When igb_set_interrupt_capability() calls
igb_reset_interrupt_capability() (e.g., because CONFIG_PCI_MSI is unset),
num_q_vectors has been set but no vector has yet been allocated.
igb_reset_interrupt_capability() will then call igb_reset_q_vector,
which assumes that the vector is allocated. As this is not the case, we
are accessing a NULL-pointer.
This patch fixes it by checking that q_vector is indeed different from
NULL.
Fixes: 02ef6e1d0b (igb: Fix queue allocation method to accommodate changing during runtime)
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
82575 has only software timestamping capability and it has
no PTP Hardware Clocks. Therefore, -1 has to be specified
to the phc_index for ethtool's get_ts_info, otherwise a wrong
value will be set to the phc_index.
v2: move the if (adapter->ptp_clock) section specifying phc_index
to above the switch statement as suggested by Matthew Vick.
adapter->ptpclock will always be NULL for 82575.
Signed-off-by: Ken ICHIKAWA <ichikawa.ken@jp.fujitsu.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for the SIOCGHWTSTAMP ioctl which enables user
processes to read the current hwtstamp_config settings
non-destructively. Previously a process had to be privileged and could
only set values, it couldn't return what is currently set without
possibly overwriting the value.
This patch adds support for this new operation into igb by keeping a
shadow copy of the config in the adapter structure, which is returned
upon request.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Additional checks are needed for a detected removal not to cause
problems. Some involve simply avoiding a lot of stuff that can't
do anything good, and also cases where the phony return value can
cause problems. In addition, down the adapter when the removal is
sensed.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check all register reads for adapter removal by checking the status
register after any register read that returns 0xFFFFFFFF. Since the
status register will never return 0xFFFFFFFF unless the adapter is
removed, such a value from a status register read confirms the
removal. Since this patch adds so much to ixgbe_read_reg, stop
inlining it, to reduce driver bloat.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make the ethtool register test use the normal register accessor
functions. Also eliminate macros used for calling register test
functions to make error exits clearer.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Kernel coding standard prefers static inline functions instead
of macros, so use them for register accessors. This is to prepare
for adding LER, Live Error Recovery, checks to those accessors.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When an adapter is removed and registers all read as all one's,
an infinite recursion can happen between ixgbe_clear_vmdq_generic
and ixgbe_clear_rar_generic. Adding a check for removal breaks
this recursion.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add an error message when the admin queue message never completes, and
fix formatting on another one that was unnecessarily wrapped.
Change-ID: I8b8a4eb7629d741f09357250144023cd4a72231f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the driver encounters an error while communicating with the PF
driver, don't just shut down the admin queue unconditionally. The PF
may be delayed, and shutting down the admin queue causes it to fail
completely. If this happens, the VF will never complete initialization.
Change-ID: I6192e9d8caeefb738428c3597fa2f54fa400ce7f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of always invoking netdev_get_tx_queue() in bcmgenet_xmit() and
bcmgenet_tx_reclaim(), just get the corresponding netdev_queue pointer
once and for all and manipulate it throughout bcmgenet_xmit() and
bcmgenet_tx_reclaim().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev_pick_tx already takes care of making sure that a given
skb->queue_mapping value will remain within the number of advertised
hardware queue number, there is no need to re-do this again in the
driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCMGENET driver was not TX timestamping the SKBs it queued for
transmission, do this in bcmgenet_xmit() right before kicking the
Transmit DMA engine.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The spinlock cookie in bcmgenet_priv is never used, get rid of it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"goto" is well accepted for error paths in the kernel but should not be
used unnecessarily. Return the correct value directly instead of using a
goto when possible.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network API functions that rely on the MDIO bus can be called as soon as
the driver calls register_netdev(). Register the MDIO bus before the
network device to avoid race conditions.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device passed to the sh_mdio_init and sh_mdio_release
functions is only used to access the sh_eth_private instance. Pass it
directly to those functions.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
