On currently supported HW there are four TX queues (three for normal
packets and one for beacons).
The driver uses just one TX queue, and declare to mac80211 to
support just one queue, but it allocates coherent memory for all
queues.
Furthermore the TX is code is written assumimg four queues exists,
and even if we decide to enable more queues in future, its mapping
rule to mac80211 is fixed.
This means we have memory waste on rtl8180/rtl8185, and we have also
not enough flexibility to add support for boards (rtl8187se) that
will use more queues.
This patch changes things in order to allocate coherent memory only
for the queues effectively used and it make it possible to specify
how to map hardware queues on mac80211 queues, that will be used
by rtl8187se code as soon it will be merged.
Note: even if the beacon queue is currently unused, this should
change, so I kept it.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hw DMA registers are written in rtl8180_init_hw function.
They are also written again just after calling rtl8180_init_hw.
There is no point in doing this twice.
Remove those redundant register writes from rtl8180_start.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current error handling of virtqueue_kick() was wrong in two places:
- The skb were freed immediately when virtqueue_kick() fail during
xmit. This may lead double free since the skb was not detached from
the virtqueue.
- try_fill_recv() returns false when virtqueue_kick() fail. This will
lead unnecessary rescheduling of refill work.
Actually, it's safe to just ignore the kick failure in those two
places. So this patch fixes this by partially revert commit
6797590118.
Fixes 6797590118
(virtio_net: verify if virtqueue_kick() succeeded).
Cc: Heinz Graalfs <graalfs@linux.vnet.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Byungho An says:
====================
This is 14th posting for SAMSUNG SXGBE driver.
Changes since v1:
- changed name of driver to SXGbE as per Ben's comment
- squashed Joe's neatening for many stuff in original patches
Changes since v2:
- updated and split binding document as per Mark's comment
- clean up codes as per Joe's comment
- removed unused fields and clean up codes as per Francois's comment
- removed module parameters as per Dave's comment
- moved driver directory to samsung/sxgbe/
Changes since v3:
- fixed Missing a blank line after declarations as per Dave's comment
- clean up codes as per Joe's comment
- removed reference of net_device.{irq, base_addr} as per Francois's comment
Changes since v4:
- updated binding document and DT related function as per Mark's comment
Changes since v5:
- updated binding document and DT related function as per Florian's comment
- fixed typo and shortened code as per Joe's comment
Changes since v6:
- updated TSO related functions as per Rayagond's comment
- updated binding document as per Mark's comment
- removed WoL patch from this patch set
Changes since v7:
- updated TSO related functions as per Rayagond's comment
Changes since v8:
- removed select and depends statement from vendor sub-section as per
Dave's comment
Changes since v9:
- removed adv-add-map, force-sf-dma-modei and force-thresh-dma-mode from
binding documnet as per Mark's comment
Changes since v10:
- clean up codes as per Francois's comment
Changes since v11:
- clean up mdio_read/write codes as per Francois's comment
- changed irq acquisition error path as per Francois's comment
- updated mdio and platform related codes as per Tomasz'comment
- clean up dma related codes as per Vince's comment
Changes since v12:
- fixed typo
Changes since v13:
- clean up error path codes for irqs as per Francois's comment
- removed unsupported functions for ehttoolirq as per Ben's comment
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces rcu_assign_pointer(x, NULL) with RCU_INIT_POINTER(x, NULL)
The rcu_assign_pointer() ensures that the initialization of a structure
is carried out before storing a pointer to that structure.
And in the case of the NULL pointer, there is no structure to initialize.
So, rcu_assign_pointer(p, NULL) can be safely converted to RCU_INIT_POINTER(p, NULL)
Signed-off-by: Monam Agarwal <monamagarwal123@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces rcu_assign_pointer(x, NULL) with RCU_INIT_POINTER(x, NULL)
The rcu_assign_pointer() ensures that the initialization of a structure
is carried out before storing a pointer to that structure.
And in the case of the NULL pointer, there is no structure to initialize.
So, rcu_assign_pointer(p, NULL) can be safely converted to RCU_INIT_POINTER(p, NULL)
Signed-off-by: Monam Agarwal <monamagarwal123@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta driver currently uses of_iomap(), which has two drawbacks:
it doesn't request the resource, and it isn't devm-style so some error
handling is needed.
This commit switches to use devm_ioremap_resource() instead, which
automatically requests the resource (so the I/O registers region shows
up properly in /proc/iomem), and also is devm-style, which allows to
get rid of some error handling to unmap the I/O registers region.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5445eaf309 ('mvneta: Try to fix mvneta when compiled as
module') fixed the mvneta driver to make it work properly when loaded
as a module in SGMII configuration, which was tested successful by the
author on the Armada XP OpenBlocks AX3, which uses SGMII.
However, it turns out that the Armada XP GP, which uses RGMII, is
affected by a similar problem: its SERDES configuration is lost when
mvneta is loaded as a module, because this configuration is set by the
bootloader, and then lost because the clock is gated by the clock
framework until the mvneta driver is loaded again and the clock is
re-enabled.
However, it turns out that for the RGMII case, setting the SERDES
configuration is not sufficient: the PCS enable bit in the
MVNETA_GMAC_CTRL_2 register must also be set, like in the SGMII
configuration.
Therefore, this commit reworks the SGMII/RGMII initialization: the
only difference between the two now is a different SERDES
configuration, all the rest is identical.
In detail, to achieve this, the commit:
* Renames MVNETA_SGMII_SERDES_CFG to MVNETA_SERDES_CFG because it is
not specific to SGMII, but also used on RGMII configurations.
* Adds a MVNETA_RGMII_SERDES_PROTO definition, that must be used as
the MVNETA_SERDES_CFG value in RGMII configurations.
* Removes the mvneta_gmac_rgmii_set() and mvneta_port_sgmii_config()
functions, and instead directly do the SGMII/RGMII configuration in
mvneta_port_up(), from where those functions where called. It is
worth mentioning that mvneta_gmac_rgmii_set() had an 'enable'
parameter that was always passed as '1', so it was pretty useless.
* Reworks the mvneta_port_up() function to set the MVNETA_SERDES_CFG
register to the appropriate value depending on the RGMII vs. SGMII
configuration. It also unconditionally set the PCS_ENABLE bit (was
already done for SGMII, but is now also needed for RGMII), and sets
the PORT_RGMII bit (which was already done for both SGMII and
RGMII).
This commit was successfully tested with mvneta compiled as a module,
on both the OpenBlocks AX3 (SGMII configuration) and the Armada XP GP
(RGMII configuration).
Reported-by: Steve McIntyre <steve@einval.com>
Cc: stable@vger.kernel.org # 3.11.x: 5445eaf309 mvneta: Try to fix mvneta when compiled as module
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for Samsung 10Gb ethernet driver(sxgbe).
- sxgbe core initialization
- Tx and Rx support
- MDIO support
- ISRs for Tx and Rx
- ifconfig support to driver
Signed-off-by: Siva Reddy Kallam <siva.kallam@samsung.com>
Signed-off-by: Vipul Pandya <vipul.pandya@samsung.com>
Signed-off-by: Girish K S <ks.giri@samsung.com>
Neatening-by: Joe Perches <joe@perches.com>
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bond send arp request to indicate that the slave is active, and if the bond dev
is a vlan dev, it will set the vlan tag in skb to notice the vlan group, but the
bond could only send a skb with 802.1q proto, not support for QinQ.
So add outer tag for lower vlan tag and inner tag for upper vlan tag to support QinQ,
The new skb will be consist of two vlan tag just like this:
dst mac | src mac | outer vlan tag | inner vlan tag | data | .....
If We don't need QinQ, the inner vlan tag could be set to 0 and use outer vlan tag
as a normal vlan group.
Using "ip link" to configure the bond for QinQ and add test log:
ip link add link bond0 bond0.20 type vlan proto 802.1ad id 20
ip link add link bond0.20 bond0.20.200 type vlan proto 802.1q id 200
ifconfig bond0.20 11.11.20.36/24
ifconfig bond0.20.200 11.11.200.36/24
echo +11.11.200.37 > /sys/class/net/bond0/bonding/arp_ip_target
90:e2:ba:07:4a:5c (oui Unknown) > Broadcast, ethertype 802.1Q-QinQ (0x88a8),length 50: vlan 20, p 0,ethertype 802.1Q, vlan 200, p 0, ethertype ARP, Ethernet (len 6), IPv4 (len 4), Request who-has 11.11.200.37 tell 11.11.200.36, length 28
90:e2:ba:06:f9:86 (oui Unknown) > 90:e2:ba:07:4a:5c (oui Unknown), ethertype 802.1Q-QinQ (0x88a8), length 50: vlan 20, p 0, ethertype 802.1Q, vlan 200, p 0, ethertype ARP, Ethernet (len 6), IPv4 (len 4), Reply 11.11.200.37 is-at 90:e2:ba:06:f9:86 (oui Unknown), length 28
v1->v2: remove the comment "TODO: QinQ?".
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It may spam if the system is out of the memory, add ratelimit for it.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add unlikely() micro to the unlikely conditions in the bond
xmit path for slight optimization.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ian made some late comments about the grant mapping series, I incorporated the
functional outcomes into this patch:
- use callback_param macro to shorten access to pending_tx_info in
xenvif_fill_frags() and xenvif_tx_submit()
- print an error message in xenvif_idx_unmap() before panic
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ian made some late comments about the grant mapping series, I incorporated the
non-functional outcomes into this patch:
- typo fixes in a comment of xenvif_free(), and add another one there as well
- typo fix for comment of rx_drain_timeout_msecs
- remove stale comment before calling xenvif_grant_handle_reset()
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the early days TX stops if there isn't enough free pending slots to
consume a maximum sized (slot-wise) packet. Probably the reason for that is to
avoid the case when we don't have enough free pending slot in the ring to finish
the packet. But if we make sure that the pending ring has the same size as the
shared ring, that shouldn't really happen. The frontend can only post packets
which fit the to the free space of the shared ring. If it doesn't, the frontend
has to stop, as it can only increase the req_prod when the whole packet fits
onto the ring.
This patch avoid using this checking, makes sure the 2 ring has the same size,
and remove a checking from the callback. As now we don't stop the NAPI instance
on this condition, we don't have to wake it up if we free pending slots up.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AFE_RX_LP_COUNTER kept the last 3 bits set, which would not properly
clear the EEE LPI mode errors bits. Make sure that those bits are set to
0 to ensure the PHY timing is always good even during EEE wake-up.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Writing first to the AFE registers, and then the VCO, RCAL, RC_CAL
registers turned out to unveil some spurious MDIO read/write failures
which would make the workaround partially applied. The fix is to write
first to the VCO, RCAL, RC_CAL registers, and then write to the AFE
registers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define constants for the various registers used in
bcm7xxx_28nm_afe_config_init() to help clarify what this workaround is
about.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Including hardware acceleration features in vlan_features breaks
stacked vlans (Q-in-Q) by marking the bottom vlan interface as
capable of acceleration. This causes one of the tags to be lost
and the packets are sent with a sing vlan header.
CC: Nithin Nayak Sujir <nsujir@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Casting a pointer to a pointer of the same type is pointless,
so remove these unnecessary casts.
Done via coccinelle script:
$ cat typecast_2.cocci
@@
type T;
T *foo;
@@
- (T *)foo
+ foo
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Casting a pointer to a pointer of the same type is pointless,
so remove these unnecessary casts.
Done via coccinelle script:
$ cat typecast_2.cocci
@@
type T;
T *foo;
@@
- (T *)foo
+ foo
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Casting a pointer to a pointer of the same type is pointless,
so remove these unnecessary casts.
Done via coccinelle script:
$ cat typecast_2.cocci
@@
type T;
T *foo;
@@
- (T *)foo
+ foo
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using addressof then casting to the original type is pointless,
so remove these unnecessary casts.
Done via coccinelle script:
$ cat typecast.cocci
@@
type T;
T foo;
@@
- (T *)&foo
+ &foo
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having the kernel to print:
"smsc911x: Driver version 2008-10-21" on every boot is not very useful, so
remove the print of the driver version.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With debug enabled we get the following message:
smsc911x smsc911x (unregistered net_device): couldn't get clock -2
As the device has not been registered at this point, it is better to use
dev_dbg() instead of netdev_dbg().
CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Suggested-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if a VF's Rx Mode will be configured to support promiscuous mode
the PF will comply, causing the VF to actually become promiscuous.
This will enable the VF to see all unicast traffic which might be intended for
other VMs, which we believe should not be possible.
This patch will cause the hypervisor to ignore the VF's request for changes in
its Rx mode (other than disabling it), preventing it from becoming promiscuous.
Reported-by: Yoann Juet <yoann.juet@univ-nantes.fr>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VFs are currently showing port statistics, although they can't really access
those - thus all such statistics will always show a value of 0.
This patch removes said statistics from the VF's view as to not confuse the
user.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we now posses a workqueue dedicated for sriov, the paradigm that sriov-
related tasks cannot sleep is no longer correct.
The VFOP mechanism was the one previously supporting said paradigm - the sriov
related tasks were broken into segments which did not require sleep, and the
mechanism re-scheduled the next segment whenever possible.
This patch remvoes the VFOP mechanism altogether - the resulting code is a much
easier to follow code; The segments are gathered into straight-forward
functions which sleep whenever neccessary.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bnx2x sriov mechanisms were done in the bnx2x slowpath workitem which
runs on the bnx2x's workqueue; This workitem is also responsible for the bottom
half of interrupt handling in the driver, and specifically it also receives
FW notifications of ramrod completions, allowing other flows to progress.
The original design of the sriov reltaed-flows was based on the notion such
flows must not sleep, since their context is the slowpath workitem.
Otherwise, we might reach timeouts - those flows may wait for ramrod completion
that will never arrive as the workitem wlll not be re-scheduled until that same
flow will be over.
In more recent time bnx2x started supporting features in which the VF interface
can be configured by the tools accessing the PF on the hypervisor.
This support created possible races on the VF-PF lock (which is taken either
when the PF is handling a VF message or when the PF is doing some slowpath work
on behalf of the VF) which may cause timeouts on the VF side and lags on the PF
side.
This patch changes the scheme - it creates a new workqueue for sriov related
tasks and moves all handling currently done in the slowpath task into the the
new workqueue.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support in a new management feature which needs the driver versions
(bnx2x, bnx2fc and bnx2i) loaded for each interface.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
Documentation/devicetree/bindings/net/micrel-ks8851.txt
net/core/netpoll.c
The net/core/netpoll.c conflict is a bug fix in 'net' happening
to code which is completely removed in 'net-next'.
In micrel-ks8851.txt we simply have overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Please pull this batch of wireless updates intended for 3.15!
For the mac80211 bits, Johannes says:
"This has a whole bunch of bugfixes for things that went into -next
previously as well as some other bugfixes I didn't want to rush into
3.14 at this point. The rest of it is some cleanups and a few small
features, the biggest of which is probably Janusz's regulatory DFS CAC
time code."
For the Bluetooth bits, Gustavo says:
"One more pull request to 3.15. This is mostly and bug fix pull request, it
contains several fixes and clean up all over the tree, plus some small new
features."
For the NFC bits, Samuel says:
"This is the NFC pull request for 3.15. With this one we have:
- Support for ISO 15693 a.k.a. NFC vicinity a.k.a. Type 5 tags. ISO
15693 are long range (1 - 2 meters) vicinity tags/cards. The kernel
now supports those through the NFC netlink and digital APIs.
- Support for TI's trf7970a chipset. This chipset relies on the NFC
digital layer and the driver currently supports type 2, 4A and 5 tags.
- Support for NXP's pn544 secure firmare download. The pn544 C3 chipsets
relies on a different firmware download protocal than the C2 one. We
now support both and use the right one depending on the version we
detect at runtime.
- Support for 4A tags from the NFC digital layer.
- A bunch of cleanups and minor fixes from Axel Lin and Thierry Escande."
For the iwlwifi bits, Emmanuel says:
"We were sending a host command while the mutex wasn't held. This
led to hard-to-catch races."
And...
"I have a fix for a "merge damage" which is not really a merge
damage: it enables scheduled scan which has been disabled in
wireless.git. Since you merged wireless.git into wireless-next.git,
this can now be fixed in wireless-next.git.
Besides this, Alex made a workaround for a hardware bug. This fix
allows us to consume less power in S3. Arik and Eliad continue to
work on D0i3 which is a run-time power saving feature. Eliad also
contributes a few bits to the rate scaling logic to which Eyal adds his
own contribution. Avri dives deep in the power code - newer firmware
will allow to enable power save in newer scenarios. Johannes made a few
clean-ups. I have the regular amount of BT Coex boring stuff. I disable
uAPSD since we identified firmware bugs that cause packet loss. One
thing that do stand out is the udev event that we now send when the
FW asserts. I hope it will allow us to debug the FW more easily."
Also included is one last iwlwifi pull for a build breakage fix...
For the Atheros bits, Kalle says:
"Michal now did some optimisations and was able to improve throughput by
100 Mbps on our MIPS based AP135 platform. Chun-Yeow added some
workarounds to be able to better use ad-hoc mode. Ben improved log
messages and added support for MSDU chaining. And, as usual, also some
smaller fixes."
Beyond that...
Andrea Merello continues his rtl8180 refactoring, in preparation for
a long-awaited rtl8187 driver. We get a new driver (rsi) for the
RS9113 chip, from Fariya Fatima. And, of course, we get the usual
round of updates for ath9k, brcmfmac, mwifiex, wil6210, etc. as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes:
drivers/net/xen-netback/netback.c: In function ‘xenvif_tx_dealloc_action’:
drivers/net/xen-netback/netback.c:1573:8: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘long int’ [-Wformat=]
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit e9275f5e2d. This commit is the
last in the netback grant mapping series, and it tries to do more aggressive
aggreagtion of unmap operations. However practical use showed almost no
positive effect, whilst with certain frontends it causes significant performance
regression.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RSSI and RATES fields are valid only when START_VALID
bit is set. So, in current implementation we have to
remember/caclulate them when START_VALID and report the same
when only END_VALID is set.
Currently during heavy traffic we could have:
- 10 packets with START_VALID - correct RSSI and RATES
- 10 packets with END_VALID
- 10 packets with START_VALID - correct RSSI and RATES
- 10 packets with END_VALID
...
Next using monitor interface we will see:
- 10 packets with correct rssi/rates
- 10 packets with rssi=-95/rate=6Mbps
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Introduce rx_status htt template instead of
stack version, as a preparation for fix
rssi and rates reporting.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Struct htt_rx_info is not needed anymore while
we will use ieee80211_rx_status structure as
a template.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kill rates, tsf, fcs_err, mic_err, amsdu_more, encrypt_type, signal
from htt_rx_info and setup this directly in ieee80211_rx_status.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
