Enable the cryptographic engine at the SoC level on the master cp110.
This engine is always present and do not depends on any pinmux
configuration.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
By adding this regulator, the SD cards are usable at higher speed
protocols such as SDR104.
This patch was tested with an SD HC card compatible with UHS-I.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 37xx SoCs has 2 SDHCI interfaces. This patch adds the second
one.
Moreover, the Armada 37xx DB v2 board populates the 2 SDHCI interfaces.
The second interface is using pluggable module that can either
have an SD connector or eMMC on it.
This patch adds support for SD module in the device DT.
[ gregory.clement@free-electrons.com:
- Add more detail in commit log
- Sort the dt node in address order
- Document the SD slot in the dts ]
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
When several groups of register address and size are used with reg, then
surround each one by angle bracket.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The initial device tree file was for the board V1.4. Now the V2.0 board
is also available. The same dtb will work for both, but the CON number
have changed, so update the comment in the dts to reflect this.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Explicitly enable the MDIO nodes in the Marvell Armada 7k DB and Marvell
Armada 8k DB. This is needed as the MDIO nodes will be disabled in the
CP 110 slave and master dtsi by a following up patch.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The EIP197 cryptographic engine supports 64 bits address width but is
limited to 40 bits on 7k/8k. Add a dma-mask property in the
cryptographic engine nodes to reflect this.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Enable the 1GB Ethernet interface that lives on the slave CP110,
with its corresponding phy (that oddly lives on the master CP110).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add the three required clocks for the MDIO interface to be functional
on Armada 8k platforms. Without this, the CPU hangs, causing RCU
stalls or the system to become unresponsive.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[Thomas:
- remove mg_core_clock, since it's a parent of mg_clock
- also add clock references to the slave CP mdio instance]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The new binding for the system controller on ap806 moved the clock into a
subnode. This preliminary step will allow to add gpio and pinctrl
subnodes
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Armada 8040 DB is equipped with 4 (2x 10G SFI + 2x 1G RGMII)
ethernet ports of which only one was hitherto enabled.
Because currently mvpp2 driver is capable of supporting only
1G RGMII/SGMII, enable second port from CP slave HW block.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add sdhci support for MACCHIATOBin boards. This uses the AP806 SDHCI
for eMMC and CP110 master for the SD card slot.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The XORv2 engines in the AP side of the Armada 7K/8K SoCs are using the
AP MS core clock as input, so this commit adds the appropriate clocks
properties.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Linksys WRT3200ACM (Rango) is the lates Armada-385 based router in
the Linksys WRT AC Series which got released in October 2016.
Key differences to the earlier Armada-385 based devices in the series is
a bigger flash chip, next generation wireless modules (Marvell 88W8964)
in the mini pcie slots as well as a Marvell SD8887. Finally the CPU is
clocked at 1866 GHz by default.
The file armada-385-linksys-rango.dts is loosly based off of a DTS
authored by Imre Kaloz.
As Rango is part of the armada-385-linksys family of boards use the
armada-385-linksys.dtsi as basis. As for functional differences to Imre
Kaloz dts, the wlan LEDs aren't connected to the expander chip pca9635
but directly to GPIOs. Then mpp47 controls the USB2.0 port and not the
USB3.0 port, so use the correct GPIO mpp44 for it. Finally use
non-removable instead of broken-cd with the sdhci node to avoid polling.
Other changes can be categorized as just cleanup / reorganization due to
using the armada-385-linksys.dtsi.
URL: 0abc3fa5a9/target/linux/mvebu/files/arch/arm/boot/dts/armada-385-linksys-rango.dts
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Buttons don't have a reg property; drop pseudo address and fixup names
of individual button nodes. Also drop #address-cells and #size-cells
properties.
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
A pin group per node is sufficient, further specialization only serves
as documentation which can be a comment just as well. This simplifies
configuring pins for nodes in dependants.
Also use labels which end up right by the node they are intended for.
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Now that we use the reference for the USB3.0 port update the node name
and labels for the phy and vbus to match the label used by
armada-38x.dtsi.
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Flatten dts of individual boards to match the new style used in
armada-385-linksys.dtsi and for the Rango addition.
* Caiman - Linksys WRT1200AC v1 & v2
* Cobra - Linksys WRT1900AC v2
* Shelby - Linksys WRT1900ACS v1 & v2
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add labels to nodes used by dependants. Also rename node gpio_keys to
gpio-keys to match the style of the rest of the file as well as the
documented example.
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Since the addition of the spi reference two styles are used. Use
references instead of recreating the same structure over and over again.
This helps to distinguish which are changes to the underlying nodes and
which are new additions and helps maintainability in general.
Verified the resulting dtb to be binary identical.
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Pull powerpc fixes from Michael Ellerman:
"Three small fixes for recently merged code:
- remove a spurious WARN_ON when a PCI device has no of_node, it's
allowed in some circumstances for there to be no of_node.
- fix the offset for store EOI MMIOs in the XIVE interrupt
controller.
- fix non-const WARN_ONs which were becoming BUGs due to them losing
BUGFLAG_WARNING in a recent cleanup patch.
Thanks to: Alexey Kardashevskiy, Alistair Popple, Benjamin
Herrenschmidt"
* tag 'powerpc-4.12-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/debug: Add missing warn flag to WARN_ON's non-builtin path
powerpc/xive: Fix offset for store EOI MMIOs
powerpc/npu-dma: Remove spurious WARN_ON when a PCI device has no of_node
Until now clk81 was used as gate clock for the ethernet controller on
Meson8 whereas Meson8b did not configure a gate clock at all. Use
CLKID_ETH for both SoCs, which is the real gate clock for the ethernet
controller.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Amlogic's Meson8b SoC has a Snoop Control Unit (SCU), just like many
other Cortex-A5 SoCs. Add the corresponding devicetree node so it can be
used during SMP boot.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds the DWC2 USB controller nodes and the corresponding USB2 PHY
nodes to meson.dtsi (as the same - or at least a very similar) IP block
is used on all SoCs (at the same physical address).
Additionally meson8.dtsi and meson8b.dtsi add the required clocks to the
DWC2 and USB2 PHY nodes, otherwise the DWC2 controller cannot be
initialized by the dwc2 driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
All supported Meson SoCs have a random number generator in CBUS.
Newer SoCs (GXBB, GXL and GXM) provide only one 32-bit random number
register, whereas the older SoCs (Meson6, Meson8 and Meson8b) have two
32-bit random number registers. The existing meson-rng driver only
supports the lower 32-bit - but it still works fine on the older SoCs
apart from this small limitation.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
There seem to be two memory regions that need to be reserved, otherwise
the system just hangs when running:
$ stress --vm-bytes $(awk '/MemFree/{printf "%d\n", $2 * 0.9;}' < /proc/meminfo)k \
--vm-keep -m 1
The first memory region is really crucial and without it the system
hangs. I could not find any references to this in Amlogic's GPL kernel
sources.
The second region is used by the "suspend firmware". The u-boot sources
(/arch/arm/cpu/aml_meson/m8/firmwareld.c) state that the suspend
firmware is located at "64M + 15M" which matches CONFIG_MESON_SUSPEND in
the Amlogic GPL kernel sources. The "suspend firmware" is responsible
for waking up the system from suspend state.
This also fixes reading the full SD card as without this the system
would simply hang (probably related to the first memory region, if some
buffer is allocated there).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds the SAR ADC to meson.dtsi and configures the clocks on Meson8
and Meson8b to allow boards to use it. Some boards use it to connect a
button to it.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds the definition of the PWM_E (CBUS) and PWM_F (AOBUS) to
meson8.dtsi, allowing devices to use them. PWM_E can be used on some
devices to generate the 32.768kHz clock for the SDIO wifi module, while
PWM_F can be used to control the power LED.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This makes meson.dtsi easier to read as we are not using magic numbers
for the GIC interrupt type (GIC_SPI) and the interrupt polarity
(IRQ_TYPE_EDGE_RISING).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This replaces the "/include/" syntax with the "#include" syntax in all
Amlogic Meson .dts and .dtsi files. That is required to use preprocessor
defines (like GIC_SPI and IRQ_TYPE_EDGE_RISING) in meson.dtsi (all files
which directly or indirectly include meson.dtsi need to use the
"#include" syntax, otherwise the .dts files cannot be compiled).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The IR receiver pins are currently defined in the CBUS pin-controller.
However the pins are in the AO region, which is controlled by the AOBUS
pin-controller. Move the pins to pinctrl_aobus so they can actually be
used.
Fixes: b60e1157d8 ("ARM: dts: amlogic: Split pinctrl device for Meson8 / Meson8b")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add nodes for the SPICC controller on GX common dtsi, GXBB and
GXL dtsi files.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This reset gpio is active low, therefore fix from active high to low.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
