Pull libata fixes from Tejun Heo:
"Dan updated tag allocation to accomodate devices which choke when tags
jump back and forth. Quite a few ahci MSI related fixes. A couple
config dependency fixes and other misc fixes"
* 'for-3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata/ahci: accommodate tag ordered controllers
ahci: Do not receive interrupts sent by dummy ports
ahci: Use pci_enable_msi_exact() instead of pci_enable_msi_range()
ahci: Ensure "MSI Revert to Single Message" mode is not enforced
ahci: do not request irq for dummy port
pata_samsung_cf: fix ata_host_activate() failure handling
pata_arasan_cf: fix ata_host_activate() failure handling
ata: fix i.MX AHCI driver dependencies
pata_at91: fix ata_host_activate() failure handling
libata: Update queued trim blacklist for M5x0 drives
libata: make AHCI_XGENE depend on PHY_XGENE
The Tegra124 clock DT binding currently provides 3 clocks that don't
actually exist; 2 for NAND and one for UART5/UARTE. Delete these. While
this is technically an incompatible DT ABI change, nothing could have
used these clock IDs for anything practical, since the HW doesn't exist.
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
As part of this make the usual change to xen_ulong_t in place of unsigned long.
This change has no impact on x86.
The Linux definition of struct multicall_entry.result differs from the Xen
definition, I think for good reasons, and used a long rather than an unsigned
long. Therefore introduce a xen_long_t, which is a long on x86 architectures
and a signed 64-bit integer on ARM.
Use uint32_t nr_calls on x86 for consistency with the ARM definition.
Build tested on amd64 and i386 builds. Runtime tested on ARM.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Add resource-managed extcon device register function for convenience.
For example, if a extcon device is attached with new
devm_extcon_dev_register(), that extcon device is automatically
unregistered on driver detach.
Signed-off-by: Sangjung Woo <sangjung.woo@samsung.com>
[Fix bug about devm_extcon_dev_match/release() and code clean by Chanwoo Choi]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
NFT_META_BRI_IIFNAME to get packet input bridge interface name
NFT_META_BRI_OIFNAME to get packet output bridge interface name
Such meta key are accessible only through NFPROTO_BRIDGE family, on a
dedicated nft meta module: nft_meta_bridge.
Suggested-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Until now, the mvebu-mbus was guessing by itself whether hardware I/O
coherency was available or not by poking into the Device Tree to see
if the coherency fabric Device Tree node was present or not.
However, on some upcoming SoCs, the presence or absence of the
coherency fabric DT node isn't sufficient: in CONFIG_SMP, the
coherency can be enabled, but not in !CONFIG_SMP.
In order to clean this up, the mvebu_mbus_dt_init() function is
extended to get a boolean argument telling whether coherency is
enabled or not. Therefore, the logic to decide whether coherency is
available or not now belongs to the core SoC code instead of the
mvebu-mbus driver itself, which is much better.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1397483228-25625-4-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
File-private locks have been re-christened as "open file description"
locks. Finish the symbol name cleanup in the internal implementation.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
cgroup is switching away from multiple hierarchies and will use one
unified default hierarchy where controllers can be dynamically enabled
and disabled per subtree. The default hierarchy will serve as the
unified hierarchy to which all controllers are attached and a css on
the default hierarchy would need to also serve the tasks of descendant
cgroups which don't have the controller enabled - ie. the tree may be
collapsed from leaf towards root when viewed from specific
controllers. This has been implemented through effective css in the
previous patches.
This patch finally implements dynamic subtree controller
enable/disable on the default hierarchy via a new knob -
"cgroup.subtree_control" which controls which controllers are enabled
on the child cgroups. Let's assume a hierarchy like the following.
root - A - B - C
\ D
root's "cgroup.subtree_control" determines which controllers are
enabled on A. A's on B. B's on C and D. This coincides with the
fact that controllers on the immediate sub-level are used to
distribute the resources of the parent. In fact, it's natural to
assume that resource control knobs of a child belong to its parent.
Enabling a controller in "cgroup.subtree_control" declares that
distribution of the respective resources of the cgroup will be
controlled. Note that this means that controller enable states are
shared among siblings.
The default hierarchy has an extra restriction - only cgroups which
don't contain any task may have controllers enabled in
"cgroup.subtree_control". Combined with the other properties of the
default hierarchy, this guarantees that, from the view point of
controllers, tasks are only on the leaf cgroups. In other words, only
leaf csses may contain tasks. This rules out situations where child
cgroups compete against internal tasks of the parent, which is a
competition between two different types of entities without any clear
way to determine resource distribution between the two. Different
controllers handle it differently and all the implemented behaviors
are ambiguous, ad-hoc, cumbersome and/or just wrong. Having this
structural constraints imposed from cgroup core removes the burden
from controller implementations and enables showing one consistent
behavior across all controllers.
When a controller is enabled or disabled, css associations for the
controller in the subtrees of each child should be updated. After
enabling, the whole subtree of a child should point to the new css of
the child. After disabling, the whole subtree of a child should point
to the cgroup's css. This is implemented by first updating cgroup
states such that cgroup_e_css() result points to the appropriate css
and then invoking cgroup_update_dfl_csses() which migrates all tasks
in the affected subtrees to the self cgroup on the default hierarchy.
* When read, "cgroup.subtree_control" lists all the currently enabled
controllers on the children of the cgroup.
* White-space separated list of controller names prefixed with either
'+' or '-' can be written to "cgroup.subtree_control". The ones
prefixed with '+' are enabled on the controller and '-' disabled.
* A controller can be enabled iff the parent's
"cgroup.subtree_control" enables it and disabled iff no child's
"cgroup.subtree_control" has it enabled.
* If a cgroup has tasks, no controller can be enabled via
"cgroup.subtree_control". Likewise, if "cgroup.subtree_control" has
some controllers enabled, tasks can't be migrated into the cgroup.
* All controllers which aren't bound on other hierarchies are
automatically associated with the root cgroup of the default
hierarchy. All the controllers which are bound to the default
hierarchy are listed in the read-only file "cgroup.controllers" in
the root directory.
* "cgroup.controllers" in all non-root cgroups is read-only file whose
content is equal to that of "cgroup.subtree_control" of the parent.
This indicates which controllers can be used in the cgroup's
"cgroup.subtree_control".
This is still experimental and there are some holes, one of which is
that ->can_attach() failure during cgroup_update_dfl_csses() may leave
the cgroups in an undefined state. The issues will be addressed by
future patches.
v2: Non-root cgroups now also have "cgroup.controllers".
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
To implement the unified hierarchy behavior, we'll need to be able to
determine the associated cgroup on the default hierarchy from css_set.
Let's add css_set->dfl_cgrp so that it can be accessed conveniently
and efficiently.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Currently, css_task_iter iterates tasks associated with a css by
visiting each css_set associated with the owning cgroup and walking
tasks of each of them. This works fine for !unified hierarchies as
each cgroup has its own css for each associated subsystem on the
hierarchy; however, on the planned unified hierarchy, a cgroup may not
have csses associated and its tasks would be considered associated
with the matching css of the nearest ancestor which has the subsystem
enabled.
This means that on the default unified hierarchy, just walking all
tasks associated with a cgroup isn't enough to walk all tasks which
are associated with the specified css. If any of its children doesn't
have the matching css enabled, task iteration should also include all
tasks from the subtree. We already added cgroup->e_csets[] to list
all css_sets effectively associated with a given css and walk css_sets
on that list instead to achieve such iteration.
This patch updates css_task_iter iteration such that it walks css_sets
on cgroup->e_csets[] instead of cgroup->cset_links if iteration is
requested on an non-dummy css. Thanks to the previous iteration
update, this change can be achieved with the addition of
css_task_iter->ss and minimal updates to css_advance_task_iter() and
css_task_iter_start().
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
This patch reorganizes css_task_iter so that adding effective css
support is easier.
* s/->cset_link/->cset_pos/ and s/->task/->task_pos/ for consistency
* ->origin_css is used to determine whether the iteration reached the
last css_set. Replace it with explicit ->cset_head so that
css_advance_task_iter() doesn't have to know the termination
condition directly.
* css_task_iter_next() currently assumes that it's walking list of
cgrp_cset_link and reaches into the current cset through the current
link to determine the termination conditions for task walking. As
this won't always be true for effective css walking, add
->tasks_head and ->mg_tasks_head and use them to control task
walking so that css_task_iter_next() doesn't have to know how
css_sets are being walked.
This patch doesn't make any behavior changes. The iteration logic
stays unchanged after the patch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
On the default unified hierarchy, a cgroup may be associated with
csses of its ancestors, which means that a css of a given cgroup may
be associated with css_sets of descendant cgroups. This means that we
can't walk all tasks associated with a css by iterating the css_sets
associated with the cgroup as there are css_sets which are pointing to
the css but linked on the descendants.
This patch adds per-subsystem list heads cgroup->e_csets[]. Any
css_set which is pointing to a css is linked to
css->cgroup->e_csets[$SUBSYS_ID] through
css_set->e_cset_node[$SUBSYS_ID]. The lists are protected by
css_set_rwsem and will allow us to walk all css_sets associated with a
given css so that we can find out all associated tasks.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
944196278d ("cgroup: move ->subsys_mask from cgroupfs_root to
cgroup") moved ->subsys_mask from cgroup_root to cgroup to prepare for
the unified hierarhcy; however, it turns out that carrying the
subsys_mask of the children in the parent, instead of itself, is a lot
more natural. This patch restores cgroup_root->subsys_mask and morphs
cgroup->subsys_mask into cgroup->child_subsys_mask.
* Uses of root->cgrp.subsys_mask are restored to root->subsys_mask.
* Remove automatic setting and clearing of cgrp->subsys_mask and
instead just inherit ->child_subsys_mask from the parent during
cgroup creation. Note that this doesn't affect any current
behaviors.
* Undo __kill_css() separation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Pull input updates from Dmitry Torokhov:
"The main change is that we now publish "firmware ID" for the serio
devices to help userspace figure out the kind of touchpads it is
dealing with: i8042 will export PS/2 port's PNP IDs as firmware IDs.
You will also get more quirks for Synaptics touchpads in various
Lenovo laptops, a change to elantech driver to recognize even more
models, and fixups to wacom and couple other drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - add support for newer elantech touchpads
Input: soc_button_array - fix a crash during rmmod
Input: synaptics - add min/max quirk for ThinkPad T431s, L440, L540, S1 Yoga and X1
Input: synaptics - report INPUT_PROP_TOPBUTTONPAD property
Input: Add INPUT_PROP_TOPBUTTONPAD device property
Input: i8042 - add firmware_id support
Input: serio - add firmware_id sysfs attribute
Input: wacom - handle 1024 pressure levels in wacom_tpc_pen
Input: wacom - references to 'wacom->data' should use 'unsigned char*'
Input: wacom - override 'pressure_max' with value from HID_USAGE_PRESSURE
Input: wacom - use full 32-bit HID Usage value in switch statement
Input: wacom - missed the last bit of expresskey for DTU-1031
Input: ads7846 - fix device usage within attribute show
Input: da9055_onkey - remove use of regmap_irq_get_virq()
The vb2 core ignores any return code from the stop_streaming op.
And there really isn't anything it can do anyway in case of an error.
So change the return type to void and update any drivers that implement it.
The int return gave drivers the idea that this operation could actually
fail, but that's really not the case.
The pwc amd sdr-msi3101 drivers both had this construction:
if (mutex_lock_interruptible(&s->v4l2_lock))
return -ERESTARTSYS;
This has been updated to just call mutex_lock(). The stop_streaming op
expects this to really stop streaming and I very much doubt this will
work reliably if stop_streaming just returns without really stopping the
DMA.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for MAX77836 chipset and its additional two LDO regulators.
These LDO regulators are controlled by the PMIC block with additional
regmap (different I2C slave address).
The MAX77836 charger and safeout regulators are almost identical to
MAX14577. The registers layout is the same, except values for charger's
current. The patch adds simple mapping between device type and supported
current by the charger regulator.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for MAX77836 chipset to the max14577 extcon driver. The
MAX77836 MUIC has additional interrupts (VIDRM, ADC1K) so IRQ handling
is split up into two functions: max14577_parse_irq() and
max77836_parse_irq().
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add Maxim 77836 support to max14577 driver. The chipsets have same MUIC
component so the extcon, charger and regulators are almost the same. The
MAX77836 however has also PMIC and Fuel Gauge.
The MAX77836 uses three I2C slave addresses and has additional interrupts
(related to PMIC and Fuel Gauge). It has also Interrupt Source register,
just like MAX77686 and MAX77693.
The MAX77836 PMIC's TOPSYS and INTSRC interrupts are reported in the
PMIC block. The PMIC block has different I2C slave address and uses own
regmap so another regmap_irq_chip is needed.
Since we have two regmap_irq_chip, use shared interrupts on MAX77836.
This patch adds additional defines and functions to the max14577 MFD core
driver so the driver will handle both chipsets. Also this patch replaces
"0x1 << N" with BIT(N) in defines for register masks.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch prepares for adding support for MAX77836 device to existing
max14577 driver by adding MAX14577 prefix to defines of interrupts.
This is only a rename-like patch, new code is not added.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch continues the preparation for adding support for MAX77836
device to existing max14577 driver.
Add enum for types of devices supported by this driver. The device type
will be detected by matching of_device_id, or i2c_device_id as a
fallback.
The patch also moves to separate function the code related to displaying
DeviceID register values.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add muic prefix to regmap config to differentiate between another regmap
config for MAX77836 PMIC node. Additionally remove unused
symbols: MAX14577_REG_INVALID and max14577_irq_source.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Adds struct device_node **bitclkmaster and struct device_node **framemaster
function parameters. With the new syntax bitclock-master and frame-master
properties can explicitly indicate the dai-link bit-clock and frame masters
with a phandle. This patch also makes the minimal changes to simple-card
for it to work with the updated snd_soc_of_parse_daifmt(). Simple-card appears
to be the only user of snd_soc_of_parse_daifmt() for now.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
This will be useful to create network family dedicated META expression
as for NFPROTO_BRIDGE for instance.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Nearly all of the registers in tps65090 combine control bits and
status bits. Turn off caching of all registers except the select few
that can be cached.
In order to avoid adding more duplicate #defines, we also move some
register offset definitions to the mfd driver (and resolve
inconsistent names).
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The only user is the info debugfs file, so we only need something
human readable. Now for both pci and platform devices we've used the
name of the underlying device driver, which matches the name of the
drm driver in all cases. So we can just use that instead.
The exception is usb, which used a generic "USB". Not to harmful with
just one usb driver, but better to use "udl", too.
With that converted we can rip out all the ->get_name implementations.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This was only ever used to pretty-print the irq driver name. And on
kms systems due to set_version bonghits we never set up the prettier
name, ever. Which make this a bit pointless.
Also, we can always dig out the driver-instance/irq relationship
through other means, so this isn't that useful. So just rip it out to
simplify the set_version/set_busid insanity a bit.
Also delete the temporary busname from drm_pci_set_busid, it's now
unused.
v2: Rebase on top of the new host1x drm_bus for tegra.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is only used for drm versions 1.0, and kms drivers have never
been there. So we can appropriately restrict this to legacy and hence
pci devices and inline everything.
v2: Make the dummy function actually return something, caught by Wu
Fengguang's 0-day tester.
v3: Fix spelling in comment (Thierry)
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Unfortunately this requires a drm-wide change, and I didn't see a sane
way around that. Luckily it's fairly simple, we just need to inline
the respective get_irq implementation from either drm_pci.c or
drm_platform.c.
With that we can now also remove drm_dev_to_irq from drm_irq.c.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To get rid of the dev->bus->get_irq callback we need to pass in the
desired irq explicitly into drm_irq_install. To avoid having to do the
same for drm_irq_unistall just track it internally. That leaves
drivers with less room to botch things up.
v2: Add the hunk lost in an earlier patch to this one (Thierry).
v3: Fix up the totally fumbled logic in drm_irq_install and use the
local variable consistently. Spotted by both Thierry and Laurent.
Shame on me for failing to properly test the rebase version of this
patch ...
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since really that's all it protects - legacy horror stories in
drm_bufs.c. Since I don't want to waste any more time on this I didn't
bother to actually look at what it protects in there, but it's at
least contained now.
v2: Move the spurious hunk to the right patch (Thierry).
Cc: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So I just wanted to add a new field to struct drm_device and
accidentally stumbled over something. According to comments
dev->open_count is protected by dev->count_lock, but that's totally
not the case. It's protected by drm_global_mutex.
Unfortunately the vga switcheroo callbacks took this comment at face
value. The problem is that we can't just take the drm_global_mutex
because:
- It would lead to a locking inversion with the driver load/unload
paths.
- It wouldn't actually protect anything, for that we'd need to wrap
the entire vga switcheroo code in the drm_global_mutex. And I'm not
sure whether that would actually solve anything.
What we probably want is a try_to_grab_switcheroo reference kind of
thing which is used in the driver's ->open callback. Then we could
move all that ->can_switch madness into the vga switcheroo core where
it really belongs.
But since that would amount to real work take the easy way out and
just add a comment. It's definitely not going to make anything worse
since doing switcheroo state changes while restarting X just isn't
recommended. Even though the delayed switching code does exactly that.
v2:
- Simplify the ->can_switch implementations more (Thierry)
- Fix comment about the dev->open_count locking (Thierry)
Cc: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> (v1)
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit f1370cc4 "xfrm: Remove useless secid field from xfrm_audit." changed
"struct xfrm_audit" to have either
{ audit_get_loginuid(current) / audit_get_sessionid(current) } or
{ INVALID_UID / -1 } pair.
This means that we can represent "struct xfrm_audit" as "bool".
This patch replaces "struct xfrm_audit" argument with "bool".
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Add a netlink multicast socket with one group to kaudit for "best-effort"
delivery to read-only userspace clients such as systemd, in addition to the
existing bidirectional unicast auditd userspace client.
Currently, auditd is intended to use the CAP_AUDIT_CONTROL and CAP_AUDIT_WRITE
capabilities, but actually uses CAP_NET_ADMIN. The CAP_AUDIT_READ capability
is added for use by read-only AUDIT_NLGRP_READLOG netlink multicast group
clients to the kaudit subsystem.
This will safely give access to services such as systemd to consume audit logs
while ensuring write access remains restricted for integrity.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register a netlink per-protocol bind fuction for audit to check userspace
process capabilities before allowing a multicast group connection.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have the netlink per-protocol optional bind function return an int error code
rather than void to signal a failure.
This will enable netlink protocols to perform extra checks including
capabilities and permissions verifications when updating memberships in
multicast groups.
In netlink_bind() and netlink_setsockopt() the call to the per-protocol bind
function was moved above the multicast group update to prevent any access to
the multicast socket groups before checking with the per-protocol bind
function. This will enable the per-protocol bind function to be used to check
permissions which could be denied before making them available, and to avoid
the messy job of undoing the addition should the per-protocol bind function
fail.
The netfilter subsystem seems to be the only one currently using the
per-protocol bind function.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added a new ancillary load (bpf call in eBPF parlance) that produces
a 32-bit random number. We are implementing it as an ancillary load
(instead of an ISA opcode) because (a) it is simpler, (b) allows easy
JITing, and (c) seems more in line with generic ISAs that do not have
"get a random number" as a instruction, but as an OS call.
The main use for this ancillary load is to perform random packet sampling.
Signed-off-by: Chema Gonzalez <chema@google.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This ethtool patch primarily copies the ioctl command data structures
from/to the User space and invokes the driver hook.
Signed-off-by: Venkat Duvvuru <VenkatKumar.Duvvuru@Emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable hibernation for ARM architectures and provide ARM
architecture specific calls used during hibernation.
The swsusp hibernation framework depends on the
platform first having functional suspend/resume.
Then, in order to enable hibernation on a given platform, a
platform_hibernation_ops structure may need to be registered with
the system in order to save/restore any SoC-specific / cpu specific
state needing (re)init over a suspend-to-disk/resume-from-disk cycle.
For example:
- "secure" SoCs that have different sets of control registers
and/or different CR reg access patterns.
- SoCs with L2 caches as the activation sequence there is
SoC-dependent; a full off-on cycle for L2 is not done
by the hibernation support code.
- SoCs requiring steps on wakeup _before_ the "generic" parts
done by cpu_suspend / cpu_resume can work correctly.
- SoCs having persistent state which is maintained during suspend
and resume, but will be lost during the power off cycle after
suspend-to-disk.
This is a rebase/rework of Frank Hofmann's v5 hibernation patchset.
Acked-by: Russ Dill <Russ.Dill@ti.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Signed-off-by: Sebastian Capella <sebastian.capella@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
[fixed duplicate virt_to_pfn() definition --rmk]
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
bs is no longer used in biovec_create_pool since 9f060e2231 ("block:
Convert integrity to bvec_alloc_bs()")
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Jens Axboe <axboe@fb.com>
Remove the 32-bit only setup_sched_clock() API now that all users
have been converted to the 64-bit friendly sched_clock_register().
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The caller needs capabilities on the namespace being queried, not on
their own namespace. This is a security bug, although it likely has
only a minor impact.
Cc: stable@vger.kernel.org
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
