Select the secondary PHY using the TCSR register, if phy-num=1
in the DTS (or phy_number is set in the platform data). The
SOC has 2 PHYs which can be used with the OTG port, and this
code allows configuring the correct one.
Note: This resolves the problem I was seeing where I couldn't
get the USB driver working at all on a dragonboard, from cold
boot. This patch depends on patch 5/14 from Ivan's msm USB
patch set. It does not use DT for the register address, as
there's no evidence that this address changes between SoC
versions.
Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix the value used for Parallel Transceiver Select (PTS) for the MSM USB
controller. This is a standard chipidea PORTSC definition, where
a PHY_TYPE of 10b (<<30) is ULPI and 11b (<<30) is SERIAL.
Fix the definitions and use them correctly in the driver code.
Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On few legacy platforms, USB PHY is having dedicated reset clk.
It is used to reset USB PHY after putting USB PHY into low power
mode and for calibration of USB PHY. Putting USB PHY into low
power mode is causing ulpi read/write timeout as expected. USB PHY
reset clk is not available on newer platform.
For 28nm PHY, reset USB PHY after resetting USB LINK.
Also reset USB PHY using USB_PHY_PON bit with USB_OTG_HS_PHY_CTRL
register after programming USB PHY Override registers as suggested
with hardware programming guidelines.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
Cc: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allow support to use 2nd HSPHY with USB2 Core.
Some platforms may have configuration to allow USB controller
work with any of the two HSPHYs present. By default driver
configures USB core to use primary HSPHY. Add support to allow
user select 2nd HSPHY using DT parameter.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Cc: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using reset framework eliminate need of platform specific
callbacks and enable reset lines to be specified in DT files.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are no references to 'pclk_src_name' in plaform code,
so it is unused.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use enum usb_dr_mode and drop default usb_dr_mode from platform data.
USB DT bindings states: dr_mode: "...In case this attribute isn't
passed via DT, USB DRD controllers should default to OTG...",
so remove redundand field.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Eliminating global variables allows driver to handle multiple
device instances.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Currently, we don't have an exit reason to notify user space about
a system-level event (for e.g. system reset or shutdown) triggered
by the VCPU. This patch adds exit reason KVM_EXIT_SYSTEM_EVENT for
this purpose. We can also inform user space about the 'type' and
architecture specific 'flags' of a system-level event using the
kvm_run structure.
This newly added KVM_EXIT_SYSTEM_EVENT will be used by KVM ARM/ARM64
in-kernel PSCI v0.2 support to reset/shutdown VMs.
Signed-off-by: Anup Patel <anup.patel@linaro.org>
Signed-off-by: Pranavkumar Sawargaonkar <pranavkumar@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
We need a common place to share PSCI related defines among ARM kernel,
ARM64 kernel, KVM ARM/ARM64 PSCI emulation, and user space.
We introduce uapi/linux/psci.h for this purpose. This newly added
header will be first used by KVM ARM/ARM64 in-kernel PSCI emulation
and user space (i.e. QEMU or KVMTOOL).
Signed-off-by: Anup Patel <anup.patel@linaro.org>
Signed-off-by: Pranavkumar Sawargaonkar <pranavkumar@linaro.org>
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
User space (i.e. QEMU or KVMTOOL) should be able to check whether KVM
ARM/ARM64 supports in-kernel PSCI v0.2 emulation. For this purpose, we
define KVM_CAP_ARM_PSCI_0_2 in KVM user space interface header.
Signed-off-by: Anup Patel <anup.patel@linaro.org>
Signed-off-by: Pranavkumar Sawargaonkar <pranavkumar@linaro.org>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Now that all accesses to FDT header data has been converted to accessor
helpers, initial_boot_params can become an opaque pointer.
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Stephen Chivers <schivers@csc.com>
Add a wrapper function to retrieve the FDT size from the FDT header. This
is primarily to avoid libfdt include paths for the whole kernel.
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Stephen Chivers <schivers@csc.com>
With libfdt support, we can take advantage of helper accessors in libfdt
for accessing the FDT header data. This makes the code more readable and
makes the FDT blob structure more opaque to the kernel. This also
prepares for removing struct boot_param_header completely.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Stephen Chivers <schivers@csc.com>
The kernel FDT functions predate libfdt and are much more limited in
functionality. Also, the kernel functions and libfdt functions are
not compatible with each other because they have different definitions
of node offsets. To avoid this incompatibility and in preparation to
add more FDT parsing functions which will need libfdt, let's first
convert the existing code to use libfdt.
The FDT unflattening, top-level FDT scanning, and property retrieval
functions are converted to use libfdt. The scanning code should be
re-worked to be more efficient and understandable by using libfdt to
find nodes directly by path or compatible strings.
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Stephen Chivers <schivers@csc.com>
Make of_get_flat_dt_prop arguments compatible with libfdt fdt_getprop
call in preparation to convert FDT code to use libfdt. Make the return
value const and the property length ptr type an int.
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Stephen Chivers <schivers@csc.com>
This is the driver for the AXI Video Direct Memory Access (AXI
VDMA) core, which is a soft Xilinx IP core that provides high-
bandwidth direct memory access between memory and AXI4-Stream
type video target peripherals. The core provides efficient two
dimensional DMA operations with independent asynchronous read
and write channel operation.
This module works on Zynq (ARM Based SoC) and Microblaze platforms.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Reviewed-by: Levente Kurusa <levex@linux.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As Joel pointed out, edma_read_position() uses memcpy_fromio() to read
the parameter ram. That's not synchronized with the internal update as
it does a byte by byte copy. We need to do a 32bit read to get a
consistent value.
Further reading destination and source is pointless. In DEV_TO_MEM
transfers we are only interested in the destination, in MEM_TO_DEV we
care about the source. In MEM_TO_MEM it really does not matter which
one you read.
Simple solution: Remove the pointers, select dest/source via a bool
and return the read value.
Remove the export of this function while at it. The only potential
user is the dmaengine and that's always builtin.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Many cpufreq drivers need to iterate over the cpufreq_frequency_table
for various tasks.
This patch introduces two macros which can be used for iteration over
cpufreq_frequency_table keeping a common coding style across drivers:
- cpufreq_for_each_entry: iterate over each entry of the table
- cpufreq_for_each_valid_entry: iterate over each entry that contains
a valid frequency.
It should have no functional changes.
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Added usage id processing for device rotation. This uses IIO
interfaces for triggered buffer to present data to user
mode.This uses HID sensor framework for registering callback
events from the sensor hub.
Data is exported to user space in the form of quaternion rotation
format.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The current scan element type uses the following format:
[be|le]:[s|u]bits/storagebits[>>shift].
To specify multiple elements in this type, added a repeat value.
So new format is:
[be|le]:[s|u]bits/storagebitsXr[>>shift].
Here r is specifying how may times, real/storage bits are repeating.
When X is value is 0 or 1, then repeat value is not used in the format,
and it will be same as existing format.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This callback is introduced to overcome some limitations of existing
read_raw callback. The functionality of both existing read_raw and
read_raw_multi is similar, both are used to request values from the
device. The current read_raw callback allows only two return values.
The new read_raw_multi allows returning multiple values. Instead of
passing just address of val and val2, it passes length and pointer
to values. Depending on the type and length of passed buffer, iio
client drivers can return multiple values.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Introduce devm_kmemdup, which uses resource managed kmalloc.
There are several request from maintainers to add this instead
of using kmemdup.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reduce copy-past a bit by adding a common helper.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nfacct objects already support accounting at the byte and packet
level. As such it is a natural extension to add the possiblity to
define a ceiling limit for both metrics.
All the support for quotas itself is added to nfnetlink acctounting
framework to stay coherent with current accounting object management.
Quota limit checks are implemented in xt_nfacct filter where
statistic collection is already done.
Pablo Neira Ayuso has also contributed to this feature.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Although rcu_assign_pointer() provides ordering guarantees,
RCU_INIT_POINTER() does not. This commit makes that explicit
in the docbook comment header.
Reported-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Because functions have the extern storage class specifier by default,
this keyword can be removed. It is redundant to use it explicitly.
Signed-off-by: Iulia Manda <iulia.manda21@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This patch enables the IBS facility when a single VCPU is running.
The facility is dynamically turned on/off as soon as other VCPUs
enter/leave the stopped state.
When this facility is operating, some instructions can be executed
faster for single-cpu guests.
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Describe the fifo parameter. It seems like kerneldoc doesn't properly
handle fields defined using a macro, so it will end up complaining about
this anyway and not generate the documentation for it either. At least
the kerneldoc is now complete.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch add device managed devm_extcon_dev_{allocate,free} to automatically
free the memory of extcon_dev structure without handling free operation.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
This patch add APIs to control the extcon device on extcon provider driver.
The extcon_dev_allocate() allocates the memory of extcon device and initializes
supported cables. And then extcon_dev_free() decrement the reference of the
device of extcon device and free the memory of the extcon device. This APIs
must need to implement devm_extcon_dev_allocate()/free() APIs.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Pull ftrace bugfix from Steven Rostedt:
"Takao Indoh reported that he was able to cause a ftrace bug while
loading a module and enabling function tracing at the same time.
He uncovered a race where the module when loaded will convert the
calls to mcount into nops, and expects the module's text to be RW.
But when function tracing is enabled, it will convert all kernel text
(core and module) from RO to RW to convert the nops to calls to ftrace
to record the function. After the convertion, it will convert all the
text back from RW to RO.
The issue is, it will also convert the module's text that is loading.
If it converts it to RO before ftrace does its conversion, it will
cause ftrace to fail and require a reboot to fix it again.
This patch moves the ftrace module update that converts calls to
mcount into nops to be done when the module state is still
MODULE_STATE_UNFORMED. This will ignore the module when the text is
being converted from RW back to RO"
* tag 'trace-fixes-v3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace/module: Hardcode ftrace_module_init() call into load_module()
Pull devicetree bug fixes from Grant Likely:
"These are some important bug fixes that need to get into v3.15.
This branch contains a pair of important bug fixes for the DT code:
- Fix some incorrect binding property names before they enter common
usage
- Fix bug where some platform devices will be unable to get their
interrupt number when they depend on an interrupt controller that
is not available at device creation time. This is a problem
causing mainline to fail on a number of ARM platforms"
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux:
of/irq: do irq resolution in platform_get_irq
of: selftest: add deferred probe interrupt test
dt: Fix binding typos in clock-names and interrupt-names
The static IRQ base is not used on any platforms with this chip
(only Ux500). Get rid of it forever, and rely on dynamic IRQ
descriptor allocation.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some off-chip GPIO expanders need to be communicated by I2C or
SPI traffic, but may still support IRQs. By the sleeping nature
of such buses, such IRQ handlers need to be threaded. Support
such handlers in the gpiochip irqchip helpers by flagging IRQs
as threaded if the .can_sleep property of the gpiochip is
true.
Helpfully deny registration of chained IRQ handlers if the
.can_sleep property is set, as such chips will invariably need
a nested handler rather than a chained handler.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This extends NL80211_CMD_SET_CHANNEL to allow dynamic channel bandwidth
changes in AP mode (including P2P GO) during a lifetime of the BSS. This
can be used to implement, e.g., HT 20/40 MHz co-existence rules on the
2.4 GHz band.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A race exists between module loading and enabling of function tracer.
CPU 1 CPU 2
----- -----
load_module()
module->state = MODULE_STATE_COMING
register_ftrace_function()
mutex_lock(&ftrace_lock);
ftrace_startup()
update_ftrace_function();
ftrace_arch_code_modify_prepare()
set_all_module_text_rw();
<enables-ftrace>
ftrace_arch_code_modify_post_process()
set_all_module_text_ro();
[ here all module text is set to RO,
including the module that is
loading!! ]
blocking_notifier_call_chain(MODULE_STATE_COMING);
ftrace_init_module()
[ tries to modify code, but it's RO, and fails!
ftrace_bug() is called]
When this race happens, ftrace_bug() will produces a nasty warning and
all of the function tracing features will be disabled until reboot.
The simple solution is to treate module load the same way the core
kernel is treated at boot. To hardcode the ftrace function modification
of converting calls to mcount into nops. This is done in init/main.c
there's no reason it could not be done in load_module(). This gives
a better control of the changes and doesn't tie the state of the
module to its notifiers as much. Ftrace is special, it needs to be
treated as such.
The reason this would work, is that the ftrace_module_init() would be
called while the module is in MODULE_STATE_UNFORMED, which is ignored
by the set_all_module_text_ro() call.
Link: http://lkml.kernel.org/r/1395637826-3312-1-git-send-email-indou.takao@jp.fujitsu.com
Reported-by: Takao Indoh <indou.takao@jp.fujitsu.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@vger.kernel.org # 2.6.38+
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The patch extends fuse_setattr_in, and extends the flush procedure
(fuse_flush_times()) called on ->write_inode() to send the ctime as well as
mtime.
Signed-off-by: Maxim Patlasov <MPatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
