On A000 HW, the SCD rdptr has only 8 bits allocated
for it, thus when checking if a queue is full, or
when checking if the SSN is equal to the TID's
next_reclaimed, A000 HW should trim the SSN.
Fix this by "normalizing" the SSN to wrap around
0xFF when comparing to the next_reclaimed on A000
HW.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't actually care about the value at all, just making sure
that we can successfully parse a single integer value, but that's
entirely pointless - remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When toggling the RF-kill pin quickly in succession, the driver can
get rather confused because it might be in the process of shutting
down, expecting all commands to go through quickly due to rfkill,
but the transport already thinks the device is accessible again,
even though it previously shut it down. This leads to bugs, and I
even observed a kernel panic.
Avoid this by making the PCIe code only report that the radio is
enabled again after the higher layers actually decided to shut it
off.
This also pulls out this common RF-kill checking code into a common
function called by both transport generations and also moves it to
the direct method - in the internal helper we don't really care
about the RF-kill status anymore since we won't report it up until
the stop anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we happen to be in or get into the queue sync when RF-kill
is asserted, we return from there and warn since there are
still queue sync notifications outstanding. These can't ever
come though, because we're in RF-kill, so don't WARN then.
While at it, also move the warning to the appropriate place,
if the request is not synchronous then we shouldn't warn, but
currently always will.
To make it fast, also trigger the waitq when on rfkill assert.
Fixes: 0636b93821 ("iwlwifi: mvm: implement driver RX queues sync command")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to debug "hardware" RF-kill flows, add a low-level hook to
allow changing the "hardware" RF-kill from debugfs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no point in duplicating exactly the same code here
for legacy and MSI-X interrupts, so pull it out into a new
function to call in both places.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case that rate's antenna is wrong at the init stage, it's
very hard to say what went wrong. Add debug data to the already
existing WARN_ON_ONCE.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some static checkers (e.g. smatch) complain about the logic, saying that
resp_cp might be leaked. Clearly that isn't true, but making the logic
easier to follow does not result in any significant code changes and makes
the code more readable by moving the NULL check closer to its source.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware moved the development from a0 MAC to z0.
z0 is using the same RFID and device ID as a0 so we only
need to switch the name.
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
New FW versions require the D0I3_END_CMD to be sent as the first
command to the FW in the resume flow. If the TLV is set, send that
command first, otherwise keep the original behavior (i.e. send last).
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There is no need to send D0I3_END_CMD as ASYNC during the system
resume flow. Additionally, the other flags used are meaningless in
this case (they were just copied from the runtime resume flow), so
remove them all.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Shaul reported that when iwlmvm was sending beacons, it didn't properly
also take ownership of the probe responses. This is because the whole
mac80211 callback (tx_last_beacon) wasn't implemented. Fix that to make
IBSS discovery work better.
Reported-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Letting the preprocessor/compiler generate the shift/mask by itself
is a win for readability, so use bitfield.h for some registers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It's safer to use scnprintf() here because the buffer might
be too short for the full format strings. In most cases
this isn't true because of external limits on the values.
In one case, this fixes a stack data leak.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Avoid one kind of symbol shadowing another in iwl_mvm_flush_sta()
by renaming the function parameter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The queue ID should never be 512 either, so correct the check
to be >= instead of just >.
Fixes: 310181ec34 ("iwlwifi: move to TVQM mode")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since we exit if buf->num_stored is 0, there's no need to
check it again later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When sending a Tx Command with a Tx packet, we allocate the
Tx command separately from the payload of the packet.
The WiFi MAC header is then copied into the buffer that was
allocated for the Tx Command. This means that this buffer
needs to be big enough to contain both. This is why it is
allocated with iwl_trans_alloc_tx_cmd which returns a
pointer to a newly allocated not zeroed struct
iwl_device_cmd.
The Tx command has a few bit fields and hence it needs to
be zeroed, but all the rest of the buffer doesn't need to
be zeroed since it will either be memcopy'ed with the MAC
header, or not even sent to the device.
This means that we don't need to zero all the
iwl_device_cmd structure, but rather only the size of
the iwl_tx_cmd structure.
Since sizeof(iwl_tx_cmd) - sizeof(iwl_tx_cmd) is about
260 bytes, this can avoid touching 4 cache lines for each
packet.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Install GTKs on AP side for new TX API.
Don't add IV space, it's added by the HW.
While at that fix GCMP abnd GCMP-256 GTK installation
which work similarly to the new TX API.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If FW isn't alive, trying to collect debug data will
result in errors both in driver and in the collected
data, so just warn and leave the collecting function
in this case.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Contrary to what some of the comments say, if rfkill was
asserted the transport will return -ERFKILL instead of
success, if CMD_WANT_SKB was set, so it's not necessary
to check cmd.resp_pkt for being NULL if the return code
was success.
Validate that this is true in iwl_trans_send_cmd().
Most of the other code modifications were done with the
following spatch:
@@
struct iwl_host_cmd cmd;
identifier pkt;
@@
<...
(
pkt = cmd.resp_pkt;
...
-if (!pkt) { ... }
|
pkt = cmd.resp_pkt;
...
-if (WARN_ON(!pkt)) { ... }
|
-if (!cmd.resp_pkt) { ... }
)
...>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In DQA mode, there is no need to wait for the TXQ to
clear out after getting a DELBA, since traffic can
continue running on the queue.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix sparse warnings in scripts/kconfig/nconf* ('make nconfig'):
../scripts/kconfig/nconf.c:1071:32: warning: Using plain integer as NULL pointer
../scripts/kconfig/nconf.c:1238:30: warning: Using plain integer as NULL pointer
../scripts/kconfig/nconf.c:511:51: warning: Using plain integer as NULL pointer
../scripts/kconfig/nconf.c:1460:6: warning: symbol 'setup_windows' was not declared. Should it be static?
../scripts/kconfig/nconf.c:274:12: warning: symbol 'current_instructions' was not declared. Should it be static?
../scripts/kconfig/nconf.c:308:22: warning: symbol 'function_keys' was not declared. Should it be static?
../scripts/kconfig/nconf.gui.c:132:17: warning: non-ANSI function declaration of function 'set_colors'
../scripts/kconfig/nconf.gui.c:195:24: warning: Using plain integer as NULL pointer
nconf.gui.o before/after files are the same.
nconf.o before/after files are the same until the 'static' function
declarations are added.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This makes TRX parsing code reusable with other platforms and parsers.
Please note this patch doesn't really change anything in the existing
code, just moves it. There is still some place for improvement (e.g.
working on non-hacky method of checking rootfs format) but it's not
really a subject of this change.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Some devices have partitions that are kind of containers with extra
subpartitions / volumes instead of e.g. a simple filesystem data. To
support such cases we need to first create normal flash device
partitions and then take care of these special ones.
It's very common case for home routers. Depending on the vendor there
are formats like TRX, Seama, TP-Link, WRGG & more. All of them are used
to embed few partitions into a single one / single firmware file.
Ideally all vendors would use some well documented / standardized format
like UBI (and some probably start doing so), but there are still
countless devices on the market using these poor vendor specific
formats.
This patch extends MTD subsystem by allowing to specify list of parsers
that should be tried for a given partition. Supporting such poor formats
is highly unlikely to be the top priority so these changes try to
minimize maintenance cost to the minimum. It reuses existing code for
these new parsers and just adds a one property and one new function.
This implementation requires setting partition parsers in a flash
parser. A proper change of bcm47xxpart will follow and in the future we
will hopefully also find a solution for doing it with ofpart
("fixed-partitions").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Some flash device partitions can be containers with extra subpartitions
(volumes). All callbacks are already capable of this additional level of
indirection.
This patch makes sure we always display subpartitions using a tree
structure and takes care of deleting subpartitions when parent gets
removed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This prepares mtd subsystem for the new feature: subpartitions. In some
cases flash device partition can be a container with extra subpartitions
(volumes).
So far there was a flat structure implemented. One master (flash device)
could be partitioned into few partitions. Every partition got its master
and it was enough to get things running.
To support subpartitions we need to store pointer to the parent for each
partition. This is required to implement more natural tree structure and
handle all recursion and offsets calculation.
To make code consistent this patch renamed "master" to the "parent" in
places where we can be dealing with subpartitions.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When support for sysfs "offset" file was added it missed to update the
del_mtd_partitions function. It deletes partitions just like
mtd_del_partition does so both should also take care of removing sysfs
files.
This change moves sysfs_remove_files call to the shared function to fix
this issue.
Fixes: a62c24d755 ("mtd: part: Add sysfs variable for offset of partition")
Cc: Dan Ehrenberg <dehrenberg@chromium.org>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There are two similar functions handling deletion. One handles single
partition and another the whole MTD flash device. They share (duplicate)
some code so it makes sense to add a small helper for that part.
Function del_mtd_partitions has been moved a bit to keep all deleting
stuff together.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This commit makes use of the AHCI_HFLAG_YES_ALPM flag to prevent
the driver from writing to the read-only Host Capability register.
It also sets the AHCI_HFLAG_NO_WRITE_TO_RO flag to prevent the AHCI
library from writing to read-only registers.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
While most hardware will simply ignore a write to a read-only register,
some hardware will signal an abort if this occurs.
This commit introduces the flag AHCI_HFLAG_NO_WRITE_TO_RO to prevent the
AHCI library from attempting to write to the HOST_CAP, HOST_CAP2, and
HOST_PORTS_IMPL registers which may be read-only.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some hardware is capable of supporting Aggresive Link Power Management
even though it is not indicated by the Host Capability register.
This commit adds the AHCI_HFLAG_YES_ALPM flag to the AHCI library to
allow indication of this quirk when the Host Capability register is
Read Only and therefore cannot be changed.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Check for pending errors when probing GHES entries. It is possible
that a fatal error is already pending at this point, so we should
handle it as soon as the driver is probed. This also avoids a
potential issue if there was an interrupt that was already
cleared for an error since the GHES driver wasn't present.
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The Denali NAND controller driver (drivers/mtd/nand/denali*) has been
largely reworked by me. Add myself as its maintainer now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This patch adds support for SoC-wide (AKA uncore) Performance Monitoring
Unit version 3.
It can support up to
- 2 IOB PMU instances
- 8 L3C PMU instances
- 2 MCB PMU instances
- 8 MCU PMU instances
and these PMUs support 64 bit counter
Signed-off-by: Hoan Tran <hotran@apm.com>
[Mark: stop counters in _xgene_pmu_isr()]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
[will: make xgene_pmu_v3_ops static]
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch moves PMU leaf functions into a function pointer structure.
It helps code maintain and expasion easier.
Signed-off-by: Hoan Tran <hotran@apm.com>
[Mark: remove redundant cast]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
[will: make xgene_pmu_ops static]
Signed-off-by: Will Deacon <will.deacon@arm.com>
In commit 613f050d68 ("perf probe: Fix to probe on gcc generated
functions in modules"), the offset from symbol is, incorrectly, added
to the trace point address. This leads to incorrect probe trace points
for inlined functions and when using relative line number on symbols.
Prior this patch:
$ perf probe -m nf_nat -D in_range
p:probe/in_range nf_nat:in_range.isra.9+0
$ perf probe -m i40e -D i40e_clean_rx_irq
p:probe/i40e_clean_rx_irq i40e:i40e_napi_poll+2212
$ perf probe -m i40e -D i40e_clean_rx_irq:16
p:probe/i40e_clean_rx_irq i40e:i40e_lan_xmit_frame+626
After:
$ perf probe -m nf_nat -D in_range
p:probe/in_range nf_nat:in_range.isra.9+0
$ perf probe -m i40e -D i40e_clean_rx_irq
p:probe/i40e_clean_rx_irq i40e:i40e_napi_poll+1106
$ perf probe -m i40e -D i40e_clean_rx_irq:16
p:probe/i40e_clean_rx_irq i40e:i40e_napi_poll+2665
Committer testing:
Using 'pfunct', a tool found in the 'dwarves' package [1], one can ask what are
the functions that while not being explicitely marked as inline, were inlined
by the compiler:
# pfunct --cc_inlined /lib/modules/4.12.0-rc4+/kernel/drivers/net/ethernet/intel/e1000e/e1000e.ko | head
__ew32
e1000_regdump
e1000e_dump_ps_pages
e1000_desc_unused
e1000e_systim_to_hwtstamp
e1000e_rx_hwtstamp
e1000e_update_rdt_wa
e1000e_update_tdt_wa
e1000_put_txbuf
e1000_consume_page
Then ask 'perf probe' to produce the kprobe_tracer probe definitions for two of
them:
# perf probe -m e1000e -D e1000e_rx_hwtstamp
p:probe/e1000e_rx_hwtstamp e1000e:e1000_receive_skb+74
# perf probe -m e1000e -D e1000_consume_page
p:probe/e1000_consume_page e1000e:e1000_clean_jumbo_rx_irq+876
p:probe/e1000_consume_page_1 e1000e:e1000_clean_jumbo_rx_irq+1506
p:probe/e1000_consume_page_2 e1000e:e1000_clean_rx_irq_ps+1074
Now lets concentrate on the 'e1000_consume_page' one, that was inlined twice in
e1000_clean_jumbo_rx_irq(), lets see what readelf says about the DWARF tags for
that function:
$ readelf -wi /lib/modules/4.12.0-rc4+/kernel/drivers/net/ethernet/intel/e1000e/e1000e.ko
<SNIP>
<1><13e27b>: Abbrev Number: 121 (DW_TAG_subprogram)
<13e27c> DW_AT_name : (indirect string, offset: 0xa8945): e1000_clean_jumbo_rx_irq
<13e287> DW_AT_low_pc : 0x17a30
<3><13e6ef>: Abbrev Number: 119 (DW_TAG_inlined_subroutine)
<13e6f0> DW_AT_abstract_origin: <0x13ed2c>
<13e6f4> DW_AT_low_pc : 0x17be6
<SNIP>
<1><13ed2c>: Abbrev Number: 142 (DW_TAG_subprogram)
<13ed2e> DW_AT_name : (indirect string, offset: 0xa54c3): e1000_consume_page
So, the first time in e1000_clean_jumbo_rx_irq() where e1000_consume_page() is
inlined is at PC 0x17be6, which subtracted from e1000_clean_jumbo_rx_irq()'s
address, gives us the offset we should use in the probe definition:
0x17be6 - 0x17a30 = 438
but above we have 876, which is twice as much.
Lets see the second inline expansion of e1000_consume_page() in
e1000_clean_jumbo_rx_irq():
<3><13e86e>: Abbrev Number: 119 (DW_TAG_inlined_subroutine)
<13e86f> DW_AT_abstract_origin: <0x13ed2c>
<13e873> DW_AT_low_pc : 0x17d21
0x17d21 - 0x17a30 = 753
So we where adding it at twice the offset from the containing function as we
should.
And then after this patch:
# perf probe -m e1000e -D e1000e_rx_hwtstamp
p:probe/e1000e_rx_hwtstamp e1000e:e1000_receive_skb+37
# perf probe -m e1000e -D e1000_consume_page
p:probe/e1000_consume_page e1000e:e1000_clean_jumbo_rx_irq+438
p:probe/e1000_consume_page_1 e1000e:e1000_clean_jumbo_rx_irq+753
p:probe/e1000_consume_page_2 e1000e:e1000_clean_jumbo_rx_irq+1353
#
Which matches the two first expansions and shows that because we were
doubling the offset it would spill over the next function:
readelf -sw /lib/modules/4.12.0-rc4+/kernel/drivers/net/ethernet/intel/e1000e/e1000e.ko
673: 0000000000017a30 1626 FUNC LOCAL DEFAULT 2 e1000_clean_jumbo_rx_irq
674: 0000000000018090 2013 FUNC LOCAL DEFAULT 2 e1000_clean_rx_irq_ps
This is the 3rd inline expansion of e1000_consume_page() in
e1000_clean_jumbo_rx_irq():
<3><13ec77>: Abbrev Number: 119 (DW_TAG_inlined_subroutine)
<13ec78> DW_AT_abstract_origin: <0x13ed2c>
<13ec7c> DW_AT_low_pc : 0x17f79
0x17f79 - 0x17a30 = 1353
So:
0x17a30 + 2 * 1353 = 0x184c2
And:
0x184c2 - 0x18090 = 1074
Which explains the bogus third expansion for e1000_consume_page() to end up at:
p:probe/e1000_consume_page_2 e1000e:e1000_clean_rx_irq_ps+1074
All fixed now :-)
[1] https://git.kernel.org/pub/scm/devel/pahole/pahole.git/
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: stable@vger.kernel.org
Fixes: 613f050d68 ("perf probe: Fix to probe on gcc generated functions in modules")
Link: http://lkml.kernel.org/r/20170621164134.5701-1-bjorn.topel@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add bindings documentation for the CC board from Shenzhen Libre
Technology
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Shenzhen Libre Technology Co., Ltd is a single board computer
manufacturer
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Pull cifs fixes from Steve French:
"Various small fixes for stable"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Fix some return values in case of error in 'crypt_message'
cifs: remove redundant return in cifs_creation_time_get
CIFS: Improve readdir verbosity
CIFS: check if pages is null rather than bv for a failed allocation
CIFS: Set ->should_dirty in cifs_user_readv()
