If the hardware is stuck, we can't read any of the memory we need to
dump it, so we end up printing only 0xa5a5a5a5, which is useless.
To solve this, poke the hardware by triggering a reset and re-enabling
the clocks if we detect a HW error.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we started using threaded irqs, all the opmode calls were changed
to be called with local_bh disabled. The reason for this was it was
that mac80211 needs that. When we are handling FW errors, mac80211 is
not involved, so we don't need it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In BSS mode in the disconnection flow, mac80211 removes
the AP station before the vif is set to unassociated.
Our firmware wants it the other way around: first set
the vif as unassociated, and then remove the AP station.
In order to bridge between those two different behaviors,
iwlmvm doesn't remove the station from the firmware when
mac80211 removes it, but only after the vif is set to
unassociated. The implementation is in
iwl_mvm_bss_info_changed_station:
if (assoc state was modified && mvmvif->ap_sta_id is VALID
&& assoc state is now UNASSC)
remove_the_station_from_the_firmware()
During the recovery flow, mac80211 re-adds the AP station
and then reconfigures the vif. Since the vif is not
associated, and then, we enter the if above (which was
intended to be taken in the disconnection flow only) and
remove the station we just added. This defeats the
recovery flow.
Fix this by not removing the AP station in this flow if
we are in recovery flow.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We allocate nvm_data in iwl_mvm_nvm_get_from_fw(). If something goes
wrong after the allocation (i.e. if no valid MAC address is valid), we
should free nvm_data before returning an error.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This function just calls kfree(), so it only obscures the code without
bringing any benefits. Remove it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Properly document the transmit buffer bits using an enum and
kernel-doc documentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add kernel-doc documentation for enum iwl_debug_cmds, linking the
structures used by the commands.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
To stop and start the FW monitor in the 7000 HW
family we need to use a different bit, otherwise
after stopping it for the first time - it won't
get restarted. Use the correct bitmask.
Note: This fix is only for DRAM collection mode.
For other modes, an additional fix will be
needed.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix the enum link by adding the missing & and provide the link
to the TX response documentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the command name is printed on command completion, the wrong
group is used, leading to the wrong name being printed. Fix this
by using the group ID without inappropriately mangling it through
iwl_cmd_groupid() - it's already a u8. Also, while at it, use it
from the same place as the command ID, everything else is just
confusing.
Fixes: ab02165cce ("iwlwifi: add wide firmware command infrastructure for TX")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When sending non-linear SKBs that should be included in the regular
TX tracing completely (and not be pushed into the tx_data tracing),
the (tracing) code didn't correctly take the fact that they were
non-linear into account and added only the skb head portion.
This probably never really triggered, since those frames we want
traced fully are most likely linear anyway, but the code gets easier
to understand and we lose an argument to the tracing function, so
overall fixing this is better.
Fixes: 206eea7833 ("iwlwifi: pcie: support frag SKBs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need to calculate the data_len outside of the tracepoint,
since it's always skb->len - hdr_len, which are both available inside.
Simplify the callers and move the calculation in.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The structure hci_serdev_client_ops does not need to be in global scope
and is not modified, so make it static.
Cleans up sparse warning:
"symbol 'hci_serdev_client_ops' was not declared. Should it be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The EMAC is present on Qualcomm Technologies' server and some mobile
chips, and is used as the primary Ethernet interface.
Systems that have these SOCs typically have an Atheros 803x or
Marvell 88e1111 PHY in them, so enable those drivers too.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now that the drivers are available, enable support for L2 and L3
performance monitoring Qualcomm Datacenter Technologies Centriq SoCs.
These PMU drivers provide support for performance optimization.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable EDAC (Error Detection and Correction) support for ARM64 server
systems that feature it, so that user space applications can be
notified of memory errors.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ARM64 server platforms can support ACPI Platform Error Interface (APEI)
and Generic Hardware Error Source (GHES) features, so enable them.
Platforms which support the firmware-first RAS error reporting model
require APEI and GHES functionality for the OS to receive and report
error records provided by the platform.
PCIe AER functionality is required for PCIe AER errors to be properly
reported and recovered from.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Some ARM64 server systems support PCIe hotplug, so enable the options
for that.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
CONFIG_EFI_CAPSULE_LOADER allows the user to update the EFI firmware,
which is useful on ARM64 server platforms.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
NVME is non-volatile storage media attached via PCIe. NVME devices
typically have much higher potential throughput than other block
devices, like SATA, NVME is a must-have requirement for ARM64 based
servers.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The CPPC CPUFreq driver is used on many ACPI-based ARM64 server systems.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Instead of unconditionally expiring the timer and calling a long
mt_release_contacts(), we can check if some slots are used when the
timer expires.
We can also remove the timer if we happen to receive all the releases.
The logic behind the MT_IO_FLAGS_PENDING_SLOTS could be implemented by
counting how many slots are active, but using bits feels slightly more
efficient.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Arek Burdach <arek.burdach@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of blindly trusting the hardware to send us release, we should
consider some events can get lost and release them when we judge time has
come.
The Windows 8 spec allows to be confident in the fact that the device
will continuously report events when a finger touches the surface.
This has been tested on the HID recording database I have, and all of
those devices behave properly.
Also, Arek tested it on his Lenovo Yoga 910, which exports such bug in
some situations, when the movements are rather slow.
We use an atomic bit here to guard against concurrent accesses to the mt
slots because both mt_process_mt_event() and mt_expired_timeout() are
called in interrupt context.
Signed-off-by: Arek Burdach <arek.burdach@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Arek Burdach <arek.burdach@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The current ITS driver is assuming every ITS hardware implementation
supports minimum of 16bit INTID. But this is not true, as per GICv3
specification, INTID field is IMPLEMENTATION DEFINED in the range of
14-24 bits. We might see an unpredictable system behavior on systems
where hardware support less than 16bits and software tries to use
64K LPI interrupts.
On Qualcomm Datacenter Technologies QDF2400 platform, boot log shows
confusing information about number of LPI chunks as shown below. The
QDF2400 ITS hardware supports 24bit INTID.
This patch allocates the memory resources for PEND/PROP tables based
on discoverable value which is specified in GITS_TYPER.IDbits. Also
it fixes the log message that reflects the correct number of LPI
chunks were allocated.
ITS@0xff7efe0000: allocated 524288 Devices @3c0400000 (indirect, esz 8, psz 64K, shr 1)
ITS@0xff7efe0000: allocated 8192 Interrupt Collections @3c0130000 (flat, esz 8, psz 64K, shr 1)
ITS@0xff7efe0000: allocated 8192 Virtual CPUs @3c0140000 (flat, esz 8, psz 64K, shr 1)
ITS: Allocated 524032 chunks for LPIs
PCI/MSI: ITS@0xff7efe0000 domain created
Platform MSI: ITS@0xff7efe0000 domain created
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add code to parse SRAT ITS Affinity sub table as defined in ACPI 6.2.
Later in per device probe, ITS devices are mapped to numa node using
ITS Id to proximity domain mapping.
[maz: fix dependency on ACPICA, fixed structure name, minor cleanups]
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Ganapatrao Kulkarni <ganapatrao.kulkarni@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Marvell ICU unit is found in the CP110 block of the Marvell Armada
7K and 8K SoCs. It collects the wired interrupts of the devices located
in the CP110 and turns them into SPI interrupts in the GIC located in
the AP806 side of the SoC, by using a memory transaction.
Until now, the ICU was configured in a static fashion by the firmware,
and Linux was relying on this static configuration. By having Linux
configure the ICU, we are more flexible, and we can allocate dynamically
the GIC SPI interrupts only for devices that are actually in use.
The driver was initially written by Hanna Hawa <hannah@marvell.com>.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This commit adds a simple driver for the Marvell GICP, a hardware unit
that converts memory writes into GIC SPI interrupts. The driver provides
a number of functions to the ICU driver to allocate GICP interrupts, and
get the physical addresses that the ICUs should write to to set/clear
interrupts.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This commit adds the Device Tree binding documentation for the Marvell
ICU interrupt controller, which collects wired interrupts from the
devices located into the CP110 hardware block of Marvell Armada 7K/8K,
and converts them into SPI interrupts in the GIC located in the AP
hardware block, using the GICP extension.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pull 'perf probe' fix from Arnaldo Carvalho de Melo:
- Do not double the offset of inline expansions when using
'perf probe' on inlined functions (Björn Töpel)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull "ARM defconfig cleanup" from Krzysztof Kozłowski:
1. Remove old Kconfig options from all ARM configs,
2. Update Samsung defconfigs to bring back options over time got disabled
for some reason (configs were not updated along with the code),
3. Save defconfigs for Samsung.
* tag 'samsung-defconfig-4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: tct_hammer_defconfig: Save defconfig
ARM: s5pv210_defconfig: Save defconfig
ARM: s3c6400_defconfig: Save defconfig
ARM: mini2440_defconfig: Save defconfig
ARM: s3c2410_defconfig: Save defconfig
ARM: exynos_defconfig: Save defconfig
ARM: s5pv210_defconfig: Bring back lost (but wanted) options
ARM: s3c6400_defconfig: Bring back lost (but wanted) options
ARM: s3c2410_defconfig: Bring back lost (but wanted) options
ARM: tct_hammer_defconfig: Bring back lost (but wanted) options
ARM: mini2440_defconfig: Bring back lost (but wanted) options
ARM: defconfig: samsung: Re-order entries to match savedefconfig
ARM: defconfig: Cleanup from old Kconfig options
The main loop in __discard_prealloc is protected by the reiserfs write lock
which is dropped across schedules like the BKL it replaced. The problem is
that it checks the value, calls a routine that schedules, and then adjusts
the state. As a result, two threads that are calling
reiserfs_prealloc_discard at the same time can race when one calls
reiserfs_free_prealloc_block, the lock is dropped, and the other calls
reiserfs_free_prealloc_block with the same block number. In the right
circumstances, it can cause the prealloc count to go negative.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Most extended attributes will fit in a single block. More importantly,
we drop the reference to the inode while holding the transaction open
so the preallocated blocks aren't released. As a result, the inode
may be evicted before it's removed from the transaction's prealloc list
which can cause memory corruption.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jan Kara <jack@suse.cz>
The F54 driver is currently only using the first 6 bytes of F54 so there is
no need to read all 27 bytes. Some Dell systems (Dell XP13 9333 and
similar) have an issue with the touchpad or I2C bus when reading reports
larger then 16 bytes. Reads larger then 16 bytes are reported in two HID
reports. Something about the back to back reports seems to cause the next
read to report incorrect data. This results in F30 failing to load and the
click button failing to work.
Previous issues with the I2C controller or touchpad were addressed in:
commit 5b65c2a029 ("HID: rmi: check sanity of the incoming report")
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=195949
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A previous set of patches "cxl: Add support for Coherent Accelerator
Interface Architecture 2.0" has introduced a new support for the CAPI
cards. These patches have been tested on Simulation environment and
quite a bit of them have been tested on real hardware.
This patch brings new fixes after a series of tests carried out on new
equipment:
- Add POWER9 definition.
- Re-enable any masked interrupts when the AFU is not activated
after resetting the AFU.
- Remove the api cxl_is_psl8/9 which is no longer useful.
- Do not dump CAPI1 registers.
- Rewrite cxl_is_page_fault() function.
- Do not register slb callack on P9.
Fixes: f24be42aab ("cxl: Add psl9 specific code")
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
kstrtoull returns 0 on success, however, in reserved_clusters_store we
will return -EINVAL if kstrtoull returns 0, it makes us fail to update
reserved_clusters value through sysfs.
Fixes: 76d33bca55
Cc: stable@vger.kernel.org # 4.4
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
