Remove creation of an soc-audio device from the machine platform_driver probe
function, and add a call to snd_soc_register_card() instead.
The current code still works, but this mechanism has been deprecated, if I'm not
mistaken. The ASoC core code produces the warning "ASoC: machine Palm/PXA27x
should use snd_soc_register_card()"
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC core code now handles creation of controls and routing based on contents of
struct snd_soc_card, so remove calls to snd_soc_dapm_new_controls() and
snd_soc_dapm_add_routes() from the snd_soc_dai_link init function, and add
widget and route definitions to struct snd_soc_card.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
These boards are using the common omap-twl4030 machine driver, no need for
separate machine drivers anymore.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Update the common machine driver to support more boards including Zoom2 and
SDP3430.
- Support for voice port of twl4030
- HS jack plug detection support
- The audio routing can be fine tuned via pdata or via provided routing
table from DT.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When HS extmute is enabled without custom GPIO we should configure the mux
to allow the pin to be used as extmute signal.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order to avoid breakage update the machine drivers at the same time using
twl4030: omap3pandora, sdp3430 and zoom2
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order to be able to use the Voice port of twl4030 three bits need to be
handled in VOICE_IF register:
VIF_EN: to enable the voice port (needed for both playback and capture)
VIF_DIN_EN: Need to be enabled for playback only (input to the codec)
VIF_DOUT_EN: Need to be enabled for capture only (output from codec)
Use DAPM_SUPPLY for the VIF_EN bit and add DAPM_AIF_IO/OUT widget to handle
the playback/capture bit.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Refactor set_pll code to avoid the following warnings:
sound/soc/codecs/wm8985.c:852:50: warning: 'pll_div.k' may be used uninitialized in this function
sound/soc/codecs/wm8985.c:849:9: warning: 'pll_div.n' may be used uninitialized in this function
sound/soc/codecs/wm8985.c:848:23: warning: 'pll_div.div2' may be used uninitialized in this function
Do the same as in commit 86ce6c9a (ASoC: WM8804: Refactor set_pll code to avoid
GCC warnings).
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When probing aux_dev, initializing is as below:
device_initialize()
device_add()
So when remove aux_dev, we need do as below:
device_del()
device_put()
Otherwise, the rtd_release() will not be called.
So here using device_unregister() to replace device_del(),
like the action in soc_remove_link_dais().
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
After called device_initialize(), even device_add() returns
error, we still need use the put_device() to release the reference
to call rtd_release(), which will do the free() action.
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There's no need to test whether a (delayed) work item in pending
before queueing, flushing or cancelling it. Most uses are unnecessary
and quite a few of them are buggy.
Remove unnecessary pending tests from wm8350. Only compile tested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In the case of no-match, return -EINVAL instead of 0.
Since we assign i to ret in the for loop, ret always less than
ARRAY_SIZE(clk_map_table). Thus remove the boundary checking for ret.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
3449f5fab8
(ASoC: fsi: add SND_SOC_DAIFMT_INV_xxx support)
added clock inversion support via snd_soc_dai_set_fmt().
Thus, this patch removed SH_FSI_xxx_INV and fsi_get_info()
from fsi driver, and modified platform settings to use new style.
Then, it cleaned up meaningless settings from platform.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ab6f6d8521
(ASoC: fsi: add master clock control functions)
added driver level clock control functions.
And now, platform depended .set_rate() is no longer needed.
This patch removed unnecessary .set_rate() platform callback support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Refactor set_pll code to avoid the following warnings:
sound/soc/codecs/wm8983.c:873:40: warning: 'pll_div.k' may be used uninitialized in this function [-Wuninitialized]
sound/soc/codecs/wm8983.c:870:9: warning: 'pll_div.n' may be used uninitialized in this function [-Wuninitialized]
sound/soc/codecs/wm8983.c:869:23: warning: 'pll_div.div2' may be used uninitialized in this function [-Wuninitialized]
Do the same as in commit 86ce6c9a (ASoC: WM8804: Refactor set_pll code to avoid
GCC warnings).
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The CS4271 requires its LRCLK and MCLK to be stable before its RESET
line is de-asserted. That also means that clocks cannot be changed
without putting the chip back into hardware reset, which also requires
a complete re-initialization of all registers.
One (undocumented) workaround is to assert and de-assert the PDN bit
in the MODE2 register.
This patch adds a new flag to both the DT bindings as well as to the
platform data to enable that workaround.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Alexander Sverdlin <subaparts@yandex.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Not very useful on non AT91/AVR32 platforms but it provides
more build coverage and prepares for ARM multiplatform.
Also fixes a couple of format type warnings.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since we are now using the clock API integration to manage MCLK we can now
use clk_get_rate() to determine if we need to divide MCLK without relying
on platform data.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Request MCLK as a clock and then enable it when carrying out a state
transtion and while ANC is active, minimising system power consumption
in idle modes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The references used for the noise gates and parameters for their triggering
are configurable, expose that to users.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The references used for the noise gates and parameters for their triggering
are configurable, expose that to users.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Though the controls are named as stereo controls in the part the main use
case for the analogue inputs to the WM5102 is mono. Reflect this in the
controls exposed to userspace, providing a series of mono controls rather
than stereo ones.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Though the controls are named as stereo controls in the part the main use
case for the analogue inputs to the WM5102 is mono. Reflect this in the
controls exposed to userspace, providing a series of mono controls rather
than stereo ones.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the FLL is being shut down we will exit early so there is no need to
check here and in fact we're checking the wrong thing anyway.
Reported-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Just found some cases that some codec drivers set the bias to _STANDBY and
set idle_bias_off to 1 during probing.
It will cause unpaired runtime_get_sync/put() issue. Also as Mark suggested,
there is no reason to start from _STANDBY bias with idle_bias_off == 1.
So here giving one warning when detected (dapm.idle_bias_off == 1) and
(dapm.bias_level != SND_SOC_BIAS_OFF) just after driver->probe().
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
sgtl5000 microphone gain only has 2 bits of resolution, so maximum value is 3.
From Eric Nelson:
"We also found that for the microphones we have here (commodity PC boom mics) a
default value of 2 for the gain gives the best results."
So change the default microphone gain as well.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Enable delay report on capture path. The delay is reset when an
URB is retired and increment at each call to .pointer based
on frame counter changes. The precision of the delay
information is limited to 1ms as in the playback case.
This reverts commit 3f94fad095.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Although we've had macros defining double _RANGE controls for a while now
they've not actually been backed up properly by the implementation, it's
treated everything as mono. Fix that by implementing the handling in the
stereo controls, ensuring that the mono controls don't mistakenly get
treated as stereo.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Both the mask and mode settings are wrong in current code.
According to the datasheet:
S2PCFG0 (0x0A)
BIT[3:1] DATA_FORMAT
serial interface protocol format:
000: left Justified
001: I2S (default)
010: right justified
100: PCM no delay
101: PCM delay
111: DSP
Thus fixes the defines for LEFT_J_DATA_FORMAT, I2S_DATA_FORMAT, and
RIGHT_J_DATA_FORMAT.
Also adds define for DATA_FORMAT_MSK.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
