... so that the fixup just needs to set the hook function in
FIXUP_ACT_PROBE. This will make easier to port for other codecs,
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new field to indicate the possible pin NID for alternative vref
setup for the shared hp/mic. Although 0x18 is valid for all Realtek
codecs, it'll be different on other vendor's codecs.
Also, drop the sanity check in update_shared_mic_hp() since the
reference pin is set explicitly in the caller side.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make the function more generic for both input and output directions,
and returns the assigned path pointer. The argument order is changed
to follow the standard (from, to) way.
Now this new function is used for analog input and loopback path
parser codes, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The amps will be initialized via activate_path(), thus it's
superfluous to set in alc_auto_init_analog_input().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove some fields from struct alc_spec, and clean up the usage.
Namely,
- spec->input_mux becomes a single element, private_imux[] is removed
- spec->adc_nids becomes an array by itself, and private_adc_nids[]
gets removed, too
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now we reached to the final big piece of parser rewrite: the input
paths. While the old parser code assumes the more-or-less direct and
similar connections from input pin to ADC, the new code handles the
complete input paths. The capture source is switched by simple calls
of activate_path() function.
The parsing of capture volume and capture switches is, however, not
fully generalized. It assumes that amps are available in the vicinity
of ADCs (in three depth). This isn't perfect but it should cover all
codecs I know of.
Also, this commit removes some NID mapping of capture-related controls
temporarily for simplicity. It'll be restored in later commits.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now we have a complete list of loopback paths, thus we can initialize
the paths more completely based on it, instead of assuming a direct
connection from pin to mixer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Don't forget to take boost volumes into account in the managed path
list. Since it's an additional volume, we need to extend the ctls[]
array.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The paths used for multi-io haven't been initialized properly, so
far. It's usually no big matter because the pins are set to input as
default, but it's still cleaner to initialize the paths properly.
Now with the path active/inactive check, we can do it easily.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The pin widget has only a single amp value for the input even if it
has multiple "sources". Handle the situation in activate_path().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
alc_auto_is_dac_reachable() can be replaced fully with
is_reachable_path(). The only difference is the order of arguments.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... and rewrite the initialization of output paths as a generic
function that is applicable for both i/o directions.
The new flag, active, is introduced to each nid_path entry. This
indicates whether the given path is active, and it's used for checking
whether a certain widget can be turned off or changed when a path is
no longer used or newly enabled.
It's still used only in the output paths. More wider adaption for
input and loopback paths will be achieved in the later patch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We are using only AUTOMUTE_MODE_PIN in patch_realtek.c and all others
have been already dropped. Let's remove the old superfluous codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The new function snd_hda_codec_amp_init() (and the stereo variant)
initializes the amp value only once at the first access. If the amp
was already initialized or updated, this won't do anything more.
It's useful for initializing the input amps that are in the part of
the path but never used.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For optimizing the verb executions, a new mechanism to cache the verbs
and amp update commands is introduced. With the new "write to cache
and flush" way, you can reduce the same verbs that have been written
multiple times.
When codec->cached_write flag is set, the further
snd_hda_codec_write_cache() and snd_hda_codec_amp_stereo() calls will
be performed only on the command or amp cache table, but not sent to
the hardware yet. Once after you call all commands and update amps,
call snd_hda_codec_resume_amp() and snd_hda_codec_resume_cache().
Then all cached writes and amp updates will be written to the
hardware, and the dirty flags are cleared.
In this implementation, the existing cache table is reused, so
actually no big code change is seen here. Each cache entry has a new
dirty flag now (so the cache key is now reduced to 31bit).
As a good side-effect by this change, snd_hda_codec_resume_*() will no
longer execute verbs that have been already issued during the resume
phase by checking the dirty flags.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable bypass when the regulator is idle, not when it is in use. This is
consistent with what the few existing users actually want.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With commit f2818d0 (ASoC: fsl: fix miscompilation of snd-soc-imx-pcm),
we will see the following build error when building modules with
CONFIG_SND_IMX_SOC=m in imx_v6_v7_defconfig.
CC [M] sound/soc/fsl/phycore-ac97.o
LD [M] sound/soc/fsl/snd-soc-fsl-ssi.o
LD [M] sound/soc/fsl/snd-soc-fsl-utils.o
LD [M] sound/soc/fsl/snd-soc-imx-ssi.o
LD [M] sound/soc/fsl/snd-soc-imx-audmux.o
LD [M] sound/soc/fsl/snd-soc-imx-pcm.o
sound/soc/fsl/imx-pcm-dma.o: In function `init_module':
imx-pcm-dma.c:(.init.text+0x0): multiple definition of `init_module'
sound/soc/fsl/imx-pcm-fiq.o:imx-pcm-fiq.c:(.init.text+0x0): first defined here
sound/soc/fsl/imx-pcm-dma.o: In function `cleanup_module':
imx-pcm-dma.c:(.exit.text+0x0): multiple definition of `cleanup_module'
sound/soc/fsl/imx-pcm-fiq.o:imx-pcm-fiq.c:(.exit.text+0x0): first defined here
make[4]: *** [sound/soc/fsl/snd-soc-imx-pcm.o] Error 1
Instead of using bool for SND_SOC_IMX_PCM_FIQ and SND_SOC_IMX_PCM_DMA
to fix the original issue, we should completely remove SND_SOC_IMX_PCM
and have imx-pcm.o statically linked with imx-pcm-fiq.o or imx-pcm-dma.o.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As the IEC-60958 channel status word is set by ANDing and ORing with
the appropriate definitions, the word bytes need to be initialized
to zero to avoid misconfiguration due to previous hw_params calls.
Signed-off-by: Ricardo Neri <rneri@dextratech.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The code to do the ramp has been removed a long time ago. Remove the
remaining code as well since this is not needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
No need to set the bias_level twice to _STANDBY - since this is the only
state the device could be at suspend time. The driver do not support
idle_bias_off yet.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert headset PLUGINT interrupt to NO_SUSPEND type in order to
allow handling of insertion/removal events while device is suspended.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The commit [0d9741c0: ALSA: usb-audio: sync ep init fix for
audioformat mismatch] introduced the correction of parameters to be
set for sync EP. But since the new code assumes that the sync EP is
always paired with the data EP of another direction, it triggers Oops
when a device only with a single direction is used.
This patch adds a proper check of sync EP type and the presence of the
paired substream for avoiding the crash.
Reported-and-tested-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASoC: Fixes for v3.8
Nothing terribly exciting here except for the DOUBLE_RANGE fix which
just hadn't worked before, nobody noticed due to lack of use.
