As we do for other fsl-mpic related cascaded irqchips
(e.g. error ints, mpic timers), use a normal irq handler
for msi irqs too.
This brings some advantages such as mask/unmask/ack/eoi
and irq state taken care behind the scenes, kstats
updates a.s.o plus access to features provided by mpic,
such as affinity.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Store cascade_data in an array inside the driver
data for later use.
Get rid of the msi_virq array since now we can
encapsulate the virqs in the cascade_data
directly and access them through the array
mentioned earlier.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Many boards share the cpufreq-cpu0 driver meaning that if we enable it in
multi_v7_defconfig we can get a reasonable amount of functional utility for
systems and test coverage for a fairly small increase in kernel size.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The virtual consumer is a test device intended to be used while developing
regulator drivers, it should never be used in production. Remove it from
all defconfigs to avoid confusion among users.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch fixes setup of second EDMA channel controller
on DA850.
* tag 'davinci-fixes-for-v3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: edma: Fix configuration parsing for SoCs with multiple eDMA3 CC
DRA7 evm REV G and later boards uses a vtt regulator for DDR3
termination and this is controlled by gpio7_11. This gpio is
configured in boot loader. gpio7_11, which is only available only on
Pad A22, in previous boards, is connected only to an unused pad on
expansion connector EXP_P3 and is safe to be muxed as GPIO on all
DRA7-evm versions (without a need to spin off another dts file).
Since gpio7_11 is used to control VTT and should not be reset or kept
in idle state during boot up else VTT will be disconnected and DDR
gets corrupted. So, as part of this change, mark gpio7 as no-reset and
no-idle on init.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While auditing the various pin ctrl configurations using the following
command:
grep PIN_ arch/arm/boot/dts/dra7-evm.dts|(while read line;
do
v=`echo "$line" | sed -e "s/\s\s*/|/g" | cut -d '|' -f1 |
cut -d 'x' -f2|tr [a-z] [A-Z]`;
HEX=`echo "obase=16;ibase=16;4A003400+$v"| bc`;
echo "$HEX ===> $line";
done)
against DRA75x/74x NDA TRM revision S(SPRUHI2S August 2014),
documentation errors were found for spi1 pinctrl. Fix the same.
Fixes: 6e58b8f1da ("ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board")
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Merge "MSM cleanups" from Linus Walleij:
This cleans out some cruft code in the MSM architecture.
* tag 'msm-cleanup-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: msm: Update the references to DEBUG_MSM_UARTx
ARM: msm: remove reference to MSM_SERIAL_DEBUGGER
ARM: msm: delete dangling mahimahi board file
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add SOC BUS support with CPU family, machine name and unique ID.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Remove existing tricks for handling PWM and use CLPS711X PWM driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Both QSPI and GPMC-NAND share the same Pin (A8) from the SoC for Chip Select
functionality. So both can't be enabled simultaneously.
Disable QSPI node to prevent the pin conflict as well as
be similar to 3.12 release.
CC: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For NAND read & write wait pin monitoring must be kept disabled as the
wait pin is only used to indicate NAND device ready status and not to
extend each read/write cycle.
So don't print a warning if wait pin is specified while read/write
monitoring is not in the device tree.
Sanity check wait pin number irrespective if read/write monitoring is
set or not.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
NAND uses wait pin only to indicate device readiness after
a block/page operation. It is not use to extend individual
read/write cycle and so read/write wait pin monitoring must
be disabled for NAND.
Add gpmc wait pin information as the NAND uses wait pin 0
for device ready indication.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
NAND uses wait pin only to indicate device readiness after
a block/page operation. It is not use to extend individual
read/write cycle and so read/write wait pin monitoring must
be disabled for NAND.
This patch also gets rid of the below warning when NAND is
accessed for the first time.
omap_l3_noc 44000000.ocp: L3 application error: target 13 mod:1 (unclearable)
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
am437x-gp-evm uses a NAND chip with page size 4096 bytes
and spare area of 225 bytes per page.
For such a setup it is preferrable to use BCH16 ECC scheme over
BCH8. This also makes it compatible with ROM code ECC scheme so
we can boot with NAND after flashing from kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
am43x-epos-evm uses a NAND chip with page size 4096 bytes
and spare area of 225 bytes per page.
For such a setup it is preferrable to use BCH16 ECC scheme over
BCH8. This also makes it compatible with ROM code ECC scheme so
we can boot with NAND after flashing from kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch removes old support for clk and clocksource support and
switches platform to use new drivers.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add the Altera SDRAM EDAC bindings and device tree changes to the Altera SoC
project.
There was a discussion thread on whether this driver should be an mfd driver
or just make use of syscon, which is already a mfd. Ultimately, the
decision to use a simple syscon interface was reached.[1]
[1] https://lkml.org/lkml/2014/7/30/514
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
[dinguyen] cleaned-up commit header and remove version history.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
This patch adds a /memreserve/ section to reserve the first 4K for future
use by the system. One possible use-case is trampoline code used to bring
secondary cores online.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
---
v3: Update commit message based on Mark Rutland's comment
v2: Add a comment in the dts files
Revision D of the SOCFGPA devkit has a GPIO line used for SD/MMC card detect.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
commit [2755e187 dts: socfpga: Add DTS entry for adding the stmmac glue
layer for stmmac.] added an extra ethernet alias in the ArriaV devkit
board file. This patch removes it.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
dw-mmc
dw-mmc controller can support multiple slots.
But, there are no use-cases anywhere. So we don't need to support the
slot-node for dw-mmc controller.
And "supports-highspeed" property in dw-mmc is deprecated.
"supports-highspeed" property can be replaced with "cap-sd/mmc-highspeed".
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Tushar Behera <trblinux@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
The r8a7740 Armadillo800EVA DTS can now be used both for
DT Multiplatform and the legacy case. Because of that
remove the r8a7740 Armadillo800EVA DT reference DTS file.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now when the r8a7740 generic multiplatform case has the same
features as the DT reference board code then get rid of the
Armadillo800EVA DT reference C board code. DT Reference code
in the future shall make use of the r8a7740 Multiplatform
support code with the generic SoC machine vector.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The base address of the second memory region on the lager
board is 0x140000000. Update the tag used in the dts file accordingly.
This is a documentation fix and should have no run-time affect.
This problem was introduced when the second memory region
was added to the lager dts file by 62bc32a257
("ARM: shmobile: Include all 4 GiB of memory on Lager)"
in v3.14.
Reported-by: NAOYA SHIIBA <naoya.shiiba.nx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The following commit prevents the MPC8548E on the XPedite5200 PrPMC
module from enumerating its PCI/PCI-X bus:
powerpc/fsl-pci: use 'Header Type' to identify PCIE mode
The previous patch prevents any Freescale PCI-X bridge from enumerating
the bus, if it is hardware strapped into Agent mode.
In PCI-X, the Host is responsible for driving the PCI-X initialization
pattern to devices on the bus, so that they know whether to operate in
conventional PCI or PCI-X mode as well as what the bus timing will be.
For a PCI-X PrPMC, the pattern is driven by the mezzanine carrier it is
installed onto. Therefore, PrPMCs are PCI-X Agents, but one per system
may still enumerate the bus.
This patch causes the device node of any PCI/PCI-X bridge strapped into
Agent mode to be checked for the fsl,pci-agent-force-enum property. If
the property is present in the node, the bridge will be allowed to
enumerate the bus.
Cc: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add CONFIG_NLS_CODEPAGE_437, CONFIG_NLS_CODEPAGE_850,
CONFIG_NLS_ISO8859_1 in default configs for 85xx
and 86xx socs. Required for mounting vfat file-systems
on USB devices
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The new MSI block in MPIC 4.3 added the MSIIR1 register,
with a different layout, in order to support 16 MSIR
registers. The msi binding was also updated so that
the "reg" reflects the newly introduced MSIIR1 register.
Virtual machines advertise these msi nodes by using the
compatible "fsl,vmpic-msi-v4.3" so add support for it.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
FSL PCI cannot directly address the whole lower 4 GiB due to
conflicts with PCICSRBAR and outbound windows. By the time
max_direct_dma_addr is set to the precise limit, it will be too late to
alter the zone limits, but we should always have at least 2 GiB mapped
(unless RAM is smaller than that).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
A DMA zone is still needed with swiotlb, for coherent allocations.
This doesn't affect platforms that don't use swiotlb or that don't call
swiotlb_detect_4g().
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
FSL PCI cannot directly address the whole lower 4 GiB due to
conflicts with PCICSRBAR and outbound windows, and thus
max_direct_dma_addr is less than 4GiB. Honor that limit in
dma_direct_alloc_coherent().
Note that setting the DMA mask to 31 bits is not an option, since many
PCI drivers would fail if we reject 32-bit DMA in dma_supported(), and
we have no control over the setting of coherent_dma_mask if
dma_supported() returns true.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Platform code can call limit_zone_pfn() to set appropriate limits
for ZONE_DMA and ZONE_DMA32, and dma_direct_alloc_coherent() will
select a suitable zone based on a device's mask and the pfn limits that
platform code has configured.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
The description of how archs should implement seccomp filters was
still strictly correct, but it failed to describe the newly
available optimizations.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
The secure_computing function took a syscall number parameter, but
it only paid any attention to that parameter if seccomp mode 1 was
enabled. Rather than coming up with a kludge to get the parameter
to work in mode 2, just remove the parameter.
To avoid churn in arches that don't have seccomp filters (and may
not even support syscall_get_nr right now), this leaves the
parameter in secure_computing_strict, which is now a real function.
For ARM, this is a bit ugly due to the fact that ARM conditionally
supports seccomp filters. Fixing that would probably only be a
couple of lines of code, but it should be coordinated with the audit
maintainers.
This will be a slight slowdown on some arches. The right fix is to
pass in all of seccomp_data instead of trying to make just the
syscall nr part be fast.
This is a prerequisite for making two-phase seccomp work cleanly.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux-s390@vger.kernel.org
Cc: x86@kernel.org
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
On the GP EVM, the ambient light sensor is limited to 100KHz on the
I2C bus.
So use 100kHz for I2C on the GP EVM due to this limitation on the
ambient light sensor.
Reported-by: Aparna Balasubramanian <aparnab@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Beaglebone white and beaglebone black differ in tiny little aspects.
This is the reason why we maintain seperate dts for these platforms.
However, there is no real way to decode from dtb which platform it is
since compatible and model name are the same for both platforms.
Fix this so that beaglebone black and beaglebone are identifiable,
while maintaining compatibility for older zImages which might use old
beaglebone compatible flag for black as well.
Reported-by: Tom Rini <trini@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The 8th NAND partition should be named "NAND.u-boot-env.backup1"
instead of "NAND.u-boot-env". This is to be consistent with other
TI boards as well as u-boot.
CC: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The I2C3 pins are taken from pads E21 (GPIO6_14) and
F20 (GPIO6_15). Use the right pinmux register and mode.
Also set the I2C3 bus frequency to a safer 400KHz than
3.4Mhz.
CC: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently we claim that omap4-panda and omap4-panda-es are essentially
the same, but they are not since PandaBoard-ES uses OMAP4460 and
PandaBoard uses OMAP4430.
So, split the common definition and make the model name available.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The arm64 interrupt migration code on cpu offline calls
irqchip.irq_set_affinity() with the argument force=true. Originally
this argument had no effect because it was not used by any interrupt
chip driver and there was no semantics defined.
This changed with commit 01f8fa4f01 ("genirq: Allow forcing cpu
affinity of interrupts") which made the force argument useful to route
interrupts to not yet online cpus without checking the target cpu
against the cpu online mask. The following commit ffde1de640
("irqchip: gic: Support forced affinity setting") implemented this for
the GIC interrupt controller.
As a consequence the cpu offline irq migration fails if CPU0 is
offlined, because CPU0 is still set in the affinity mask and the
validation against cpu online mask is skipped to the force argument
being true. The following first_cpu(mask) selection always selects
CPU0 as the target.
Commit 601c942176d8("arm64: use cpu_online_mask when using forced
irq_set_affinity") intended to fix the above mentioned issue but
introduced another issue where affinity can be migrated to a wrong
CPU due to unconditional copy of cpu_online_mask.
As with for arm, solve the issue by calling irq_set_affinity() with
force=false from the CPU offline irq migration code so the GIC driver
validates the affinity mask against CPU online mask and therefore
removes CPU0 from the possible target candidates. Also revert the
changes done in the commit 601c942176 as it's no longer needed.
Tested on Juno platform.
Fixes: 601c942176d8("arm64: use cpu_online_mask when using forced
irq_set_affinity")
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org> # 3.10.x
Signed-off-by: Will Deacon <will.deacon@arm.com>
Pull more arm64 fixes from Will Deacon:
"Another handful of arm64 fixes here. They address some issues found
by running smatch on the arch code (ignoring the false positives) and
also stop 32-bit Android from losing track of its stack.
There's one additional irq migration fix in the pipeline, but it came
in after I'd tagged and tested this set.
- a few fixes for real issues found by smatch (after Dan's talk at KS)
- revert the /proc/cpuinfo changes merged during the merge window.
We've opened a can of worms here, so we need to find out where we
stand before we change this interface.
- implement KSTK_ESP for compat tasks, otherwise 32-bit Android gets
confused wondering where its [stack] has gone
- misc fixes (fpsimd context handling, crypto, ...)"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
Revert "arm64: cpuinfo: print info for all CPUs"
arm64: fix bug for reloading FPSIMD state after cpu power off
arm64: report correct stack pointer in KSTK_ESP for compat tasks
arm64: Add brackets around user_stack_pointer()
arm64: perf: don't rely on layout of pt_regs when grabbing sp or pc
arm64: ptrace: fix compat reg getter/setter return values
arm64: ptrace: fix compat hardware watchpoint reporting
arm64: Remove unused variable in head.S
arm64/crypto: remove redundant update of data
