The Marvell Armada 375 and Armada 38x SOCs, which use the Cortex-A9
CPU core, the PL310 cache and the Marvell PCIe hardware block are
affected a L2/PCIe deadlock caused by a system erratum when hardware
I/O coherency is used.
This deadlock can be avoided by mapping the PCIe memory areas as
strongly-ordered (note: MT_UNCACHED is strongly-ordered), and by
removing the outer cache sync done in software. This is implemented in
this patch by:
* Registering a custom arch_ioremap_caller function that allows to
make sure PCI memory regions are mapped MT_UNCACHED.
* Adding at runtime the 'arm,io-coherent' property to the PL310 cache
controller. This cannot be done permanently in the DT, because the
hardware I/O coherency can only be enabled when CONFIG_SMP is
enabled, in the current kernel situation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1400165974-9059-4-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Kconfig symbol USB_MUSB_PERIPHERAL was removed in v3.1. The last two
checks for its macro now always evaluate to false. So remove these
checks.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
[nsekhar@ti.com: also cleaned-up usage in defconfig file]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The i12 tvbox is an A20 based android tvbox, with 512M / 1G RAM, 4G nand flash,
ap6210 or ap6330 sdio wifi + bt (broadcom sdio wifi + uart attached brcm bt),
2USB host ports using USB-A receptacles and a micro-usb receptacle for USB OTG,
and 100Mbit ethernet using an IP101a phy.
The PCB is labelled i12-a20 hence I've named the board i12-a20. It is used
in noname allwinner A20 tv-boxes, which are sometimes sold with Q5 or
QT840A as product name.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
bus-width defaults to 1, and all 4 lines are hooked up at the cubietruck,
properly set bus-width to 4.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The following parameters are no longer needed by the edma driver since the
information can be obtained from the IP's CCCFG register:
n_channel, n_region, n_slot and n_tc.
Remove the initialization of n_cc as well since in this context it has no
meaning. We have separate edma_soc_info struct/eDMA3_CC instance so this
member does not make any sense (and the driver no longer uses it).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
dma-channels, ti,edma-regions and ti,edma-slots no longer needed in DT since
the the same information is available in the IP's CCCFG register.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
dma-channels, ti,edma-regions and ti,edma-slots no longer needed in DT since
the the same information is available in the IP's CCCFG register.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
From CCCFG register of eDMA3 we can get all the needed information for the
driver about the IP:
Number of channels: NUM_DMACH
Number of regions: NUM_REGN
Number of slots (PaRAM sets): NUM_PAENTRY
Number of TC/EQ: NUM_EVQUE
In case when booted with DT or the queue_priority_mapping is not provided
set up a default priority map.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
To be consistent in the code that we take parameters from edma_cc[j] struct
and not randomly from info[j] as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The struct edma is allocated per CC bases so the member num_cc does not make
any sense. One CC is one CC, it does not have sub CCs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The Colombus has a full size SD slot wired to the MMC0 controller. In order to
work, the MMC lines have to have the pull-ups enabled though.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
The unit-address doesn't match the reg property. Since the reg property is
correct, change the unit-address accordingly.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The colombus board has a on-board USB hub, that is enabled through the pin
PH24, and wired to the first EHCI controller.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Switch the device tree to the new compatibles introduced in the i2c drivers
to have a common pattern accross all Allwinner SoCs.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If CMA is turned on and CMA size is set to zero, kernel should
behave as if CMA was not enabled at compile time.
Every dma allocation should check existence of cma area
before requesting memory.
Signed-off-by: Gioh Kim <gioh.kim@lge.com>
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
[mszyprow: removed redundant empty line from the patch]
Signed-off-by: <m.szyprowski@samsung.com>
Samsung DT updates for v3.16
- exynos4
: add missing pinctrls
- exynos4412-trats2
: update camera nodes and add rear camera nodes
: rename alias for i2c_ak8975 label
Update camera nodes for exynos4 and exynos4412-trats2
- exynos5250
: update DWC3 usb controller and enable to use generic USB DRD phy
- exynos5250-snow
: enable dp-controller, fimd, hdmi and pwm backlight
: add sound node and Vbus regulator for USB 3.0
: add tps65090 power regulator
: add pinctrl for EC irq and i2c-arbitrator
- exynos5420
: change to correct compatible string for hdmi
: add PD entry to MFC codec and enable DWC3 and USB 3.0 PHY
: add MFC memory banks for smdk5420 and arndale-octa boards
- exynos5420-peach-pit
: add support exynos5420 based peach-pit board
: add sound node and Vbus regulatro for USB 3.0
: enable dp-controller, fimd
- exynos5420-smdk5420
: add Vbus regulatro for USB 3.0
- use generic DT bindings for map SYSRAM
[olof: Fixed up conflict with a fix for 4212 secondary CPU startup, carrying
over the fix to the reworked code]
* tag 'samsung-dt' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (32 commits)
ARM: dts: Add MFC memory banks to exynos5420 boards
ARM: dts: enable dp-controller for exynos5420-peach-pit board
ARM: dts: enable fimd for exynos5420 based peach-pit board
ARM: dts: enable dp-controller for exynos5250-snow board
ARM: dts: enable fimd for exynos5250-snow board
ARM: dts: enable pwm backlight for exynos5250-snow
ARM: dts: Add pwmX_out pinctrl nodes to exynos5250
ARM: dts: Add Vbus regulator for USB 3.0 on exynos5420-smdk5420
ARM: dts: Add Vbus regulator for USB 3.0 on exynos5420-peach-pit
ARM: dts: Add Vbus regulator for USB 3.0 on exynos5250-snow
ARM: dts: Add PD entry to MFC codec on exynos5420
ARM: dts: Add sound node for exynos5420-peach-pit board
ARM: dts: Add sound node for exynos5250-snow board
ARM: dts: Update DWC3 usb controller to use new phy driver for exynos5250
ARM: dts: Enable support for generic USB DRD phy for exynos5250
ARM: dts: Enable support for DWC3 controller for exynos5420
ARM: dts: Enable support for USB 3.0 PHY controller for exynos5420
ARM: dts: enable hdmi for exynos5420-peach-pit board
ARM: dts: change to correct compatible string for exynos5420 hdmi
ARM: dts: enable hdmi for exynos5250 based snow board
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merging in Samsung fixes for 3.15-rc to avoid an annoying context conflict
with new DT code.
* commit '702b691e4a71':
ARM: dts: Remove g2d_pd node for exynos5420
ARM: dts: Remove mau_pd node for exynos5420
ARM: exynos_defconfig: enable HS-I2C to fix for mmc partition mount
ARM: dts: disable MDMA1 node for exynos5420
ARM: EXYNOS: fix the secondary CPU boot of exynos4212
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Samsung S3C24XX updates for 3.16" from Kukjin Kim:
Samsung S3C24XX to use the common clock framework
- S3C2412, S3C2413, S3C2416 and S3C2443 to use CCF
- S3C2410, S3C2440, S3C2442 to use CCF
- Remove legacy samsung clock from mach-s3c24xx/
- Some of them are missed from previous pull-request
- Clock related sutff got ack from Mike and Tomasz
- Created the last commit due to missing changes
during re-sorting because this branch is provided
as a base to samsung clk tree.
* tag 's3c24xx-clk' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (23 commits)
ARM: S3C24XX: fix merge conflict
ARM: S3C24XX: remove SAMSUNG_CLOCK remnants after ccf conversion
ARM: S3C24XX: remove legacy clock code
ARM: S3C24XX: convert s3c2410 to common clock framework
ARM: S3C24XX: convert s3c2440 and s3c2442 to common clock framework
ARM: S3C24XX: add platform code for conversion to the common clock framework
clk: samsung: add clock controller driver for s3c2410, s3c2440 and s3c2442
dt-bindings: add documentation for s3c2410 clock controller
ARM: S3C24XX: enable usage of common dclk if common clock framework is enabled
clk: samsung: add clock driver for external clock outputs
ARM: S3C24XX: cpufreq-utils: don't write raw values to MPLLCON when using ccf
ARM: S3C24XX: convert s3c2412 to common clock framework
clk: samsung: add clock controller driver for s3c2412
dt-bindings: add documentation for s3c2412 clock controller
clk: samsung: add plls used by the early s3c24xx cpus
ARM: S3C24XX: only store clock registers when old clock code is active
ARM: S3C24XX: Convert s3c2416 and s3c2443 to common clock framework
ARM: dts: add clock data for s3c2416
ARM: S3C24XX: prevent conflicts between ccf and non-ccf s3c24xx-socs
clk: samsung: add clock-driver for s3c2416, s3c2443 and s3c2450
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull "omap fixes for v3.15-rc cycle" from Tony Lindgren:
Regression fixes for omaps for NAND, DMA, cpu_idle and audio.
Also a minor one line fix for audio clock on 54xx.
* tag 'omap-for-v3.15/fixes-v3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4: Fix the boot regression with CPU_IDLE enabled
ARM: OMAP2+: Fix DMA hang after off-idle
ARM: OMAP2+: nand: Fix NAND on OMAP2 and OMAP3 boards
ARM: omap5: hwmod_data: Correct IDLEMODE for McPDM
ARM: OMAP3: clock: Back-propagate rate change from cam_mclk to dpll4_m5 on all OMAP3 platforms
Signed-off-by: Olof Johansson <olof@lixom.net>
It is ignored by the edma driver since we are just setting back the default
mapping of TC -> Queue.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
There is no need to change the default TC -> Queue mapping. By default the
mapping is: TC0 -> Q0, TC1 -> Q1, etc.
Changing this has no benefits at all and all the board files are just setting
the same mapping back to the HW.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Instead of saving the for loop length, take the num_tc value from the pdata.
In case of DT boot set the n_tc to 3 as it is hardwired in edma_of_parse_dt()
This is a temporary state since upcoming patch(es) will change how we are
dealing with these parameters.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The pdata has been just allocated with devm_kzalloc() in
edma_setup_info_from_dt() and passed to this function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Samsung fixes for 3.15 from Kukjin Kim:
- Remove g2d_pd and mau_pd nodes on exynos5420.
Since the power domains are linked to the CMU blocks,
kernel panic happens during access clocks when the
power domains are disabled. Now this is a best solution.
- Enable HS-I2C on exynos5 by default
MMC partition cannot be mounted for RFS without the
enabling HS-I2C because regulators for MMC power are
connected to HS-I2C bus.
- Disable MDMA1 node on exynos5420
When MDMA1 runs in secure mode it makes kernel fault,
so need to disalbe it on exynos5420 by default instead
of each board.
- Fix the secondary CPU boot for exynos4212
* tag 'samsung-fixes' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Remove g2d_pd node for exynos5420
ARM: dts: Remove mau_pd node for exynos5420
ARM: exynos_defconfig: enable HS-I2C to fix for mmc partition mount
ARM: dts: disable MDMA1 node for exynos5420
ARM: EXYNOS: fix the secondary CPU boot of exynos4212
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Second Round of Renesas ARM Based SoC r7s72100 CCF Updates for v3.16"
from Simon Horman:
r7s72100 (RZ/A1H) SoC based Genmai board
* Remove non-multiplatform support from genmai-reference
* tag 'renesas-r7s72100-ccf2-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Remove Genmai reference DTS
ARM: shmobile: Let Genmai multiplatform boot with Genmai DTB
ARM: shmobile: Sync Genmai DTS with Genmai reference DTS
ARM: shmobile: genmai-reference: Remove legacy clock support
ARM: shmobile: Remove non-multiplatform Genmai reference support
Signed-off-by: Olof Johansson <olof@lixom.net>
Get the two interrupt line number at the same time by merging the two
instance of if(node){}else{} places.
replace the &pdev->dev with the already existing dev which makes it possible
to collapse lines with devm_request_irq()
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add support to PHY of USB2 of the Exynos5250 SoC.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
[gautam.vivek@samsung.com: Split the usb phy entries]
[gautam.vivek@samsung.com: Added phy entry for OHCI also along with EHCI]
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Vikas Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds sysreg-syscon node to exynos5250 and exynos5420 device
tree, to access System Register's registers using syscon driver.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
[gautam.vivek@samsung.com: Split this syreg-syscon dts entry]
[gautam.vivek@samsung.com: added similar syscon entry for exynos5420]
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
[vikas.sajjan@samsung.com: updated the binding document]
Signed-off-by: Vikas Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
DP Hpd Gpio pin which is "gpx2-6" in Exynos 5420 based peach board,
belongs to Pinctrl_0. It has moved to pinctrl_0 from pinctrl_3.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Merge "ARM: tegra: defconfig updates for 3.16" from Stephen Warren:
AT24C EEPROM:
This is used for the board ID EEPROM on Jetson TK1, as well as likely
a whole slew of other NVIDIA reference boards; we simply haven't added
enabled the EEPROM in the DT files until now.
MTD_SPI_NOR:
This defconfig contains the CONFIG_M25P80 symbol, which is now
dependent on the MTD_SPI_NOR symbol. Add CONFIG_MTD_SPI_NOR to satisfy
the new dependency.
FRAMEBUFFER_CONSOLE_ROTATION:
Needed for devices like Tegra Note 7 and NVIDIA SHIELD to get the boot
console in the expected orientation.
CAN*, RTC_DRV_DS1307:
Toradex Colibri Evaluation Board uses the DS1307 RTC and the MCP251x CAN
controller. The NVIDIA Tegra 3 based Colibri T30 module can be used on
this carrier board.
Furthermore the NVIDIA Tegra 3 based Apalis T30 module too contains two
MCP251x CAN controllers.
INPUT_JOYDEV:
NVIDIA SHIELD embeds a USB joystick device.
* tag 'tegra-for-3.16-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: tegra_defconfig updates
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: tegra: core code changes for 3.16" from Stephen Warren:
This branch contains just a single patch this time around. Thierry
enhanced Tegra's restart code to allow programming PMC scratch registers
to request specific behaviour after reboot. One of the most useful
options for mainline software is the ability to reboot directly into USB
recovery mode, which e.g. allows the bootloader to be reflashed.
* tag 'tegra-for-3.16-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Support reboot modes
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: imx: device tree changes for 3.16" from Shawn Guo:
i.MX device tree changes for 3.16:
- New board support: imx35-pdk, imx51-digi-connectcore, imx6dl-phytec,
imx6dl-riotboard, and vf610-colibri.
- Improve device tree support for imx51-babbage and eukrea-cpuimx51 to
get the same level support as board files, so that we can kill the
board files.
- Quite some updates on imx27-phytec-phycore board support from
Alexander Shiyan
- Enable USB, sound and touchscreen on the eukrea imx25/35/51 boards,
from Denis Carikli
- Quite a lot of patches from Fabio Estevam, updating Freescale
imx25-pdk and imx27-pdk board support
- Correct USB device configuration for imx25/35
- Fixes i2c4 device node in imx6dl.dtsi regarding to compatible string
and clock data
- Enable HDMI, TVE, LVDS display support on a bunch of imx5/6 boards
- Update PCIe to the new binding and enable PCIe support on
imx6qdl-sabresd board
- A couple of imx6q-dmo-edmqmx6 updates from Lucas Stach, adding pfuze
irq gpio and SPI flash
- Enable CODA7541 VPU for i.MX53
- A series of updates on imx6qdl-phytec boards from Philipp Zabel
- Small cleanups and fixes on board imx28-duckbill - Michael Heimpold
- Add stdout-path property to i.MX boards
- Karo TX25 board updates from Sascha Hauer
- Enable pwm and sdhc devices for board vf610-twr
* tag 'imx-dt-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (105 commits)
ARM: dts: imx35-pdk: Fix memory region description
ARM: dts: imx51-eukrea-mbimxsd51-baseboard: Add CAN support
ARM: dts: imx6: add new board RIoTboard
ARM: dts: imx6: i2c4 cleanup
ARM: dts: imx6: edmqmx6: add vcc and vio power supplies to stmpe
ARM: dts: Karo TX25: use hardware ecc
ARM: dts: Karo TX25: Add phy reset gpio and supply for FEC
ARM: dts: Karo TX25: Add pinctrl nodes
ARM: dts: i.MX25: Add IRAM node
ARM: dts: i.MX25: Add mmc aliases
ARM: dts: i.MX51 babbage: Fix FEC pad ctrl settings
ARM: dts: imx6qdl-sabresd: Add USDHC4 support
ARM: imx: add HDMI support for SolidRun HummingBoard and Cubox-i
ARM: dts: imx6: edmqmx6: add SPI bus and flash
ARM: dts: imx6: edmqmx6: add pinctrl for pfuze irq gpio
ARM: dts: imx6q-udoo: Add HDMI support
ARM: dts: Add stdout-path property to i.MX boards
ARM: dts: imx: Fix LVDS mapping for Ventana GW52xx
ARM: dts: imx: add LVDS backlight for Ventana
ARM: dts: imx6qdl-sabresd: remove power-on gpio from pcie
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: imx: soc changes for 3.16" from Shawn Guo:
i.MX SoC changes for 3.16:
- A few cleanups on mx21ads board file, which should make the later
conversion to DT a little bit easier.
- Add some missing clocks and drop unused clk lookups for i.MX1 and
i.MX27 clock drivers
- Add initial i.MX SoloX (imx6sx) SoC support
- Remove mx51_babbage and mach-cpuimx51sd board files, as the
equivalent DT support is ready for the boards
- Clean up device tree timer initialization a little bit
- Add missing i2c4 clock for i.MX6 DualLite/Solo
- Add missing CKO clock i.MX25
- Add shared gate clock support for i.MX specific clk_gate2
- Add low-level debug support for SoC VF610
- Some random code cleanups and defconfig updates
* tag 'imx-soc-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (33 commits)
ARM: mx25: Add CLKO support
ARM: i.MX1 clk: Remove clk_register_clkdev() for unused clocks
ARM: i.MX1 clk: Add missing clocks
ARM: imx: add basic imx6sx SoC support
ARM: imx: add clock driver for imx6sx
ARM: imx: add low-level debug support for imx6sx
ARM: mx51: Remove mach-cpuimx51sd board file
ARM: i.MX: Setup IRQ handler from IRQ driver
ARM: i.MX27 pca100: remove deprecated IRQF_DISABLED
ARM: imx/mxs defconfigs: add MTD_SPI_NOR (new dependency for M25P80)
ARM: i.MX: Fix eMMa PrP resource size
ARM: imx_v4_v5_defconfig: drop CONFIG_COMMON_CLK_DEBUG option
ARM: i.MX27 clk: Remove clk_register_clkdev() for unused clocks
ARM: i.MX27 clk: Add missing clocks for MSHC and RTIC
ARM: imx6q: add the missing esai_ahb clock
ARM: imx: add shared gate clock support
ARM: imx: lock is always valid for clk_gate2
ARM: imx: define struct clk_gate2 on our own
ARM: i.MX: Remove #ifdef CONFIG_OF
ARM: imx_v6_v7_defconfig: enable option CONFIG_LOCALVERSION_AUTO
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Allwinner defconfig additions for 3.16" from Maxime Ripard.
* tag 'sunxi-defconfig-for-3.16' of https://github.com/mripard/linux:
ARM: sunxi: drop CONFIG_COMMON_CLK_DEBUG
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Allwinner DT additions for 3.16" from Maxime Ripard:
- Introduction of the MMC controlers
- New board: A10s R7, Mele M9, APP4-EVB1
- Enabled the PMU on the Cortex A7-based SoCs
* tag 'sunxi-dt-for-3.16' of https://github.com/mripard/linux: (38 commits)
ARM: sunxi: dt: declare the r_pio pin controller for A31 SoC
ARM: sunxi: dt: add PRCM clk and reset controller subdevices
ARM: sunxi: dt: add APP4-EVB1 board support
ARM: sun6i: dt: Add support for the USB controllers
ARM: sun6i: Add the USB clocks to the DTSI
ARM: dts: sun5i: Add new A10s r7 hdmi tv dongle board
ARM: dts: sun7i: Add reg_vcc3v3 to sun7i board mmc nodes
ARM: dts: sun6i: Add reg_vcc3v3 to sun6i board mmc nodes
ARM: dts: sun5i: Add reg_vcc3v3 to sun5i board mmc nodes
ARM: dts: sun4i: Add reg_vcc3v3 to sun4i board mmc nodes
ARM: dts: sunxi: Add reg_vcc3v3 supply to sunxi-common-regulators.dtsi
ARM: dts: sun7i: Add basic support for the Cubietruck WiFi module
ARM: dts: sun7i: Enable mmc controller on various A20 boards
ARM: dts: sun7i: Add pin-muxing info for the mmc controllers
ARM: dts: sun7i: Add mmc controller nodes
ARM: dts: sun6i: Add new sun6i-a31-m9 dts file for Mele M9
ARM: dts: sun6i: Add mmc controller nodes
ARM: dts: sun6i: Add mmc clocks
ARM: dts: sun5i: Enable mmc controller on various A10s and A13 boards
ARM: dts: sun5i: Add mmc controller nodes
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Allwinner SoCs core additions for 3.16" from Maxime Ripard:
Refactor the Kconfig options to have one Kconfig option per machine.
* tag 'sunxi-core-for-3.16' of https://github.com/mripard/linux:
ARM: sunxi: select MFD_SUN6I_PRCM when sun6i arch support is enabled
ARM: sunxi: Split the various SoCs support in Kconfig
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Renesas ARM Based r7s72100 SoC CCF Updates for v3.16" from Simon Horman:
r7s72100 (RZ/A1H) SoC and its Genmai board
* Add and use CCF support
* Initislise SCIF, I2C and SPI via DT
* tag 'renesas-r7s72100-ccf-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r7s72100: use workaround for non DT-clocks
ARM: shmobile: Add forward declaration of struct clk to silence warning
ARM: shmobile: r7s72100: remove SPI DT clocks from legacy clock support
ARM: shmobile: r7s72100: add spi clocks to dtsi
ARM: shmobile: r7s72100: remove I2C DT clocks from legacy clock support
ARM: shmobile: r7s72100: add i2c clocks to dtsi
ARM: shmobile: r7s72100: genmai: platform scif devices only for legacy support
ARM: shmobile: r7s72100: genmai: add uart alias and activate scif2 as console
ARM: shmobile: r7s72100: add scif nodes to dtsi
ARM: shmobile: r7s72100: genmai: populate nodes for external clocks
ARM: shmobile: r7s72100: add essential clock nodes to dtsi
ARM: shmobile: r7s72100: document MSTP clock support
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Renesas ARM Based SoC dt-scif Updates for v3.16" from Simon Horman:
r8a7791 (R-Car M2) based Koelsch board and
r8a7790 (R-Car H1) based Lager board
* Enable SCIF0 and SCIF1 serial ports in DT
* tag 'renesas-dt-scif-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: koelsch: Enable SCIF0 and SCIF1 serial ports in DT
ARM: shmobile: lager: Enable SCIF0 and SCIF1 serial ports in DT
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM Versatile Express updates for 3.16" from Pawel Moll:
This series reworks VE's platform configuration infrastructure by:
- making it possible to instantiate selected devices from the
Device Tree, prior to massive population,
- converting custom "func" API into standard "regmap",
- splitting the existing MFD driver into smaller ones and placing
them into relevant directories.
The common clock framework driver can now be selected individually
(mostly for arm64 sake, where some of them are not used at all).
It also simplifies the machine code, by:
- moving the shed clock info clocksource driver,
- simplifying SMP operations to base them entirely of the DT data,
- moving platform ID checks into relevant driver.
* tag 'vexpress/updates-for-3.16' of git://git.linaro.org/people/pawel.moll/linux:
ARM: vexpress: move HBI check to sysreg driver
ARM: vexpress: Simplify SMP operations for DT-powered system
ARM: vexpress: remove redundant vexpress_dt_cpus_num to get cpu count
clocksource: Sched clock source for Versatile Express
clk: versatile: Split config options for sp810 and vexpress_osc
mfd: vexpress: Define the device as MFD cells
mfd: syscon: Add platform data with a regmap config name
mfd: vexpress: Convert custom func API to regmap
of: Keep track of populated platform devices
+ Linux 3.15-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Renesas SoC Clock Cleanups for v3.16" from Simon Horman:
Work from Laurent Pinchart to switch all Renesas platforms to the new style
CMT, MTU2 and TMU device platform data. This is in preparation for
initialising these devices using DT on ARM Based Renesas SoCs.
* tag 'renesas-clock-cleanup2-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r7s72100: Switch to new style MTU2 device
sh: Switch to new style MTU2 device
ARM: shmobile: r8a7779: Switch to new style TMU device
ARM: shmobile: r8a7778: Switch to new style TMU device
ARM: shmobile: r8a7740: Switch to new style TMU device
ARM: shmobile: sh73a0: Switch to new style TMU device
ARM: shmobile: sh7372: Switch to new style TMU device
sh: Switch to new style TMU device
ARM: shmobile: r8a7791: Switch to new style CMT device
ARM: shmobile: r8a7790: Switch to new style CMT device
ARM: shmobile: r8a7740: Switch to new style CMT device
ARM: shmobile: r8a73a4: Switch to new style CMT device
ARM: shmobile: sh73a0: Switch to new style CMT device
ARM: shmobile: sh7372: Switch to new style CMT device
sh: Switch to new style CMT device
Signed-off-by: Olof Johansson <olof@lixom.net>
There are two LEDs available on the B2020 RevE board, one red, one
green. In this patch we enable the red one for "heartbeat" and turn
the green one off.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
The B2020 RevE differs from the other B2020 boards in a few subtle ways;
including the Ethernet reset GPIO which this patch adds support for and
the LED wiring which will follow in a latter patch. Without supplying
these differences Ethernet and the board LEDs simply will not work.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Interconnect clocks are not yet managed at the init, then
we have to start the kernel with clk_ignore_unused.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
