Since commit 7adb0933b1 (ARM: dts: omap4: Set all audio related
IP's status to disabled as default) all audio related device are
disabled by default. Most boards were updated to enable devices
explicitly, but DuoVero was missed.
mcpdm is used for twl6040 and mcbsp1 is used for BlueTooth audio.
Cc: florian.vaussard@epfl.ch
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
MTD NAND partition for file-system should start at offset=0xA00000
Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA7xx platform has in-build GPMC and ELM h/w engines which can be used
for accessing externel NAND flash device. This patch:
- adds generic DT binding in dra7.dtsi for enabling GPMC and ELM h/w engines
- adds DT binding for Micron NAND Flash (MT29F2G16AADWP) present on dra7-evm
*Important*
On DRA7 EVM, GPMC_WPN and NAND_BOOTn are controlled by DIP switch
So following board settings are required for NAND device detection:
SW5.9 (GPMC_WPN) = LOW
SW5.1 (NAND_BOOTn) = HIGH
Signed-off-by: Minal Shah <minalkshah@gmail.com>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add CPSW ethernet support for AM437x GP EVM which has one slave pinned out
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add cpsw phy sel device tree node for selecting phy mode in control module
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Both the VAR-STK-OM44 and VAR-DVK-OM44 boards comes with the
WLAN/BT version of the system on module VAR-SOM-OM44.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP4/5 TRMs primarily list address offsets from the padconf
physical address (which is not driver base address) and not
always the absolute physical address for padconf registers like
some other OMAP TRMs. So create a new macro to use this offset
and to avoid confusion between different OMAP parts.
For more information, see the tables in TRM for named something like
"Device Core Control Module Pad Configuration Register Fields"
and "Device Wake-Up Control Module Pad Configuration Register Fields"
Note that we now also have to update cm-t54 for the fixed up
offsets.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
[tony@atomide.com: updated comments, updated cm-t54]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the files in /sys/devices/soc0/ show no information about
DRA7. Few userspace programs do depend on this information to make SoC
specific support. So update logic to detect the relevant information and
provide to userspace.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In omap2_common_pm_late_init suspend_set_ops was called to set common
suspend handling functions for all omap platforms. This created two
problems. First, these suspend ops were being set for all platforms,
regardless of whether or not suspend support has been integrated so in
the case of AM33XX, suspend to mem was presented as available but
failed every time. Second, some platforms will need to define a
completely separate set of suspend ops, such as AM33XX, due to
differences from previous omap platforms so there is no need to
always set the common omap ops.
This patch moves the suspend_set_ops call from omap2_common_pm_late_init
into a separate function that then gets called in the omap*_pm_init
functions for each platform.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the SD Card reader and the internal eMMC on the Berlin BG2Q DMP
using two of the SDHCI nodes of the Berlin BG2Q.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Add pinctrl bindings and system control nodes to what we currently know
about Berlin SoCs. Where available, also set default pinctrl property
for uarts, when there is only one pinmux option for it.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This converts Berlin BG2 SoC dtsi to make use of the new DT clock
nodes for Berlin SoCs. While at it, also fix up twdclk which is
running at cpuclk/3 instead of sysclk.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This converts Berlin BG2CD SoC dtsi to make use of the new DT clock
nodes for Berlin SoCs. Also add a binding include to ease core clock
references.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The Berlin BG2 has 32 GPIOs in SoC power domain and 16 in the SM one.
Only the first 8 SM GPIOs have interrupt support.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Adds initial support for the Marvell BG2-Q DMP. The board has 2GB of
memory, an uart activated and what's initially supported by the Marvell
Armada 1500 pro dtsi.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Adds initial support for the Marvell Armada 1500 pro (BG2Q) SoC (Berlin family).
The SoC has nodes for cpu, l2 cache controller, interrupt controllers, local
timer, apb timers and uarts for now. Also add corresponding binding documentation.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Now that we start supporting the Marvell Berlin BG2Q, add a symbol allowing to
differentiate that SoC from the other SoCs of the Berlin family.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
On OMAP4 panda board, there have been several bug reports about boot
hang and lock-ups with CPU_IDLE enabled. The root cause of the issue
is missing interrupts while in idle state. Commit cb7094e8 {cpuidle / omap4 :
use CPUIDLE_FLAG_TIMER_STOP flag} moved the broadcast notifiers to common
code for right reasons but on OMAP4 which suffers from a nasty ROM code
bug with GIC, commit ff999b8a {ARM: OMAP4460: Workaround for ROM bug ..},
we loose interrupts which leads to issues like lock-up, hangs etc.
Patch reverts commit cb7094 {cpuidle / omap4 : use CPUIDLE_FLAG_TIMER_STOP
flag} and 54769d6 {cpuidle: OMAP4: remove timer broadcast initialization} to
avoid the issue. With this change, OMAP4 panda boards, the mentioned
issues are getting fixed. We no longer loose interrupts which was the cause
of the regression.
Fixes: cb7094e8 (cpuidle / omap4 : use CPUIDLE_FLAG_TIMER_STOP flag)
Fixes: ff999b8a (cpuidle: OMAP4: remove timer broadcast initialization)
Cc: stable@vger.kernel.org # v3.9+
Cc: Roger Quadros <rogerq@ti.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Reported-tested-by: Roger Quadros <rogerq@ti.com>
Reported-tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
LDO4 regulator was getting disabled preventing the system from
going into low power states. Keep it always on to fix it.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixed incorrect compatible for ak8975 magnetic sensor.
ak8975 magnetic sensor use compatible "ak8975" or "asahi-kasei,ak8975"
In this patch, use "asahi-kasei,ak8975" according to dt bindings document.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The audio setup on Peach-pit board is similar to Snow board, hence the
sound-card driver used on Snow board can be reused on Peach-pit board.
Peach-pit board uses MAX98090 audio codec.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The audio codec on Snow board, MAX98095 is connected on I2C7 bus.
Also it requires the GPX1-7 line to be pulled up.
Updated Snow DTS file to incorporate above changes and added a
sound node to instantiate the I2S-based sound card.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Removing the dt node for older usb3 phy driver from Exynos5250
device tree and updating the dt node for DWC3 controller to
use new phy driver based on generic phy framework.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add device tree nodes for USB 3.0 PHY present alongwith
USB 3.0 controller Exynos 5420 SoC. This phy driver is
based on generic phy framework.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
