With pinctrl-single,bits it is possible to update just part of the register
within the pinctrl-single,function-mask area.
This is useful when one register configures mmore than one pin's mux.
pinctrl-single,bits takes three parameters:
<reg offset, value, sub-mask>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
[Removed a misplaced comment]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It replaces the clk_register_clkdev in imx6q clock driver with DT
lookup. It depends on Mike's clk-3.7 branch.
* tag 'imx-clk-dt-lookup' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx6q: replace clk_register_clkdev with clock DT lookup
Resolved context add/remove conflict in arch/arm/boot/dts/imx6q.dtsi
It replaces clk_register_clkdev in mxs clock driver with DT lookup.
* tag 'mxs-clk-dt-lookup' of git://git.linaro.org/people/shawnguo/linux-2.6:
clk: mxs: replace imx23 clk_register_clkdev with clock DT lookup
clk: mxs: replace imx28 clk_register_clkdev with clock DT lookup
SPEAr platforms now support DT and so must convert all drivers to support DT.
This patch adds DT probing support for Arasan Compact Flash controller and
updates its documentation too.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Calxeda highbank SATA phy has intermittent problems bringing up a link
with Gen3 drives. Retrying the phy hard reset can work-around this issue,
but each reset also disables spread spectrum support. The reset function
also needs to reprogram the phy to enable spread spectrum support.
Create a new driver based on ahci_platform to support the Calxeda Highbank
SATA controller.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Changes for GPMC (General Purpose Memory Controller) that take it
closer for being just a regular device driver.
Remove the ancient omap specific atags that are no longer needed.
At some point we were planning to pass the bootloader information
with custom atags that did not work out too well.
There's no need for these any longer as the kernel has been booting
fine without them for quite some time. And Now we have device tree
support that can be used instead.
Freescale's Integrated Flash controller (IFC) may have one or two
interrupts. In case of single interrupt line, it will cover all IFC
interrupts.
Update this information in IFC device tree bindings
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
i.MX usb controllers share non-core registers, which may include
SoC specific controls. We turn it into a usbmisc device and usbmisc
driver set operations needed by ci13xxx_imx driver.
For example, Sabrelite board has bad over-current design, we can
usbmisc to disable over-current detection.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For following the standard, define more channel map positions and
shuffle the items a bit:
- As both PulseAudio and gstreamer define MONO channel position
explicitly, we should follow that, too. The mono streams point to
this channel position unless they are explicitly assigned to certain
channel positions.
- Top-front-* and Top-rear-* positions are added, carried from
PulseAudio's definitions.
- Move NA and MONO definitions at the top of table right after
UNKNOWN, since these are more abstract in comparison with other
practical positions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
add of support for the davinci i2c driver.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
[wsa: fix indentation in the binding description]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
usb: musb: patches for v3.7 merge window
Here we have a bunch of miscellaneous cleanups and fixes
to the musb driver. It fixes a bunch of mistakes errors
which nobody has triggered before, so I'm not Ccing stable
tree.
We are finally improving OMAP's VBUS/ID Mailbox usage so
that we can introduce our PHY drivers properly. Also, we're
adding support for multiple instances of the MUSB IP in
the same SoC, as seen on some platforms from TI which
have 2 MUSB instances.
Other than that, we have some small fixes like not kicking
DMA for a zero byte transfer, or properly handling NAK timeout
on MUSB's host side, and the enabling of DMA Mode1 for any
transfers which are aligned to wMaxPacketSize.
All patches have been pending on mailing list for a long time
and I don't expect any big surprises with this pull request.
usb: xceiv: patches for v3.7 merge window
nop xceiv got its own header to avoid polluting otg.h. It has also
learned to work as USB2 and USB3 phys so we can use it on USB3
controllers.
Together with those two changes to nop xceiv, we're adding basic
PHY support to dwc3 driver, this is to allow platforms which actually
have a SW-controllable PHY talk to them through dwc3 driver.
We're adding a new phy driver for the OMAP architecture. This driver
is for the PHY found in OMAP4 SoCs, and a new phy driver for the
marvell architecture. An extra phy driver - for Tegra SoCs - is now
moving from arch/arm/mach-tegra* to drivers/usb/phy.
Also here, there's the creation of <linux/usb/phy.h> which should be
used from now on for PHY drivers, even those which don't support
OTG.
Added device tree support for dsps musb glue driver and updated the
Documentation with device tree binding information.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Santhapuri, Damodar <damodar.santhapuri@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
[afzal@ti.com: use '-' instead of '_' for dt properties]
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It really becomes an maintenance issue that every time a device needs
to look up (clk_get) a clock we have to patch kernel clock file to call
clk_register_clkdev for that clock.
Since clock DT support which is meant to resolve clock lookup in device
tree is in place, the patch moves imx6q client devices' clock lookup
over to device tree, so that any new lookup to be added at later time
can just get done in DT instead of kernel.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The name of each led channel is configurable.
If the name is NULL, just use the channel id for making the channel name
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Added device tree support for omap musb driver and updated the
Documentation with device tree binding information.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It really becomes a maintenance issue that every time a device needs
to look up (clk_get) a clock we have to patch kernel clock file to call
clk_register_clkdev for that clock.
Since clock DT support which is meant to resolve clock lookup in device
tree is in place, the patch moves imx23 client devices' clock lookup
over to device tree, so that any new lookup to be added at later time
can just get done in DT instead of kernel.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It really becomes a maintenance issue that every time a device needs
to look up (clk_get) a clock we have to patch kernel clock file to call
clk_register_clkdev for that clock.
Since clock DT support which is meant to resolve clock lookup in device
tree is in place, the patch moves imx28 client devices' clock lookup
over to device tree, so that any new lookup to be added at later time
can just get done in DT instead of kernel.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds two sysfs files for each usb hub port to allow userspace
to control the port power policy.
For an upcoming Intel xHCI roothub, this will translate into ACPI calls
to completely power off or power on the port. As a reminder, when these
ports are completely powered off, the USB host and device will see a
physical disconnect. All future USB device connections will be lost,
and the device will not be able to signal a remote wakeup.
The control sysfs file can be written to with two options:
"on" - port power must be on.
"off" - port must be off.
The state sysfs file reports usb port's power state:
"on" - powered on
"off" - powered off
"error" - can't get power state
For now, let userspace dictate the port power off policy. Future
patches may add an in-kernel policy.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch turns each USB port on a hub into a new struct device. This
new device has the USB hub interface device as its parent. The port
devices are stored in a new structure (usb_port), and an array of
usb_ports are dynamically allocated once we know how many ports the USB
hub has.
Move the port_owner variable out of usb_hub and into this new structure.
A new file will be created in the hub interface sysfs directory, so
add documentation.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add resource managed variants of pwm_get() and pwm_put() for
convenience. Code is largely inspired by the equivalent devm functions
of the regulator framework.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
ENOTTY is now returned for unimplemented ioctl by dvb-frontend.
Old EOPNOTSUPP & ENOSYS could be still returned by some drivers
as well as other "non standard" error codes.
EAGAIN is returned in case of device is in state where it cannot
perform requested operation. This is for example sleep and statistics
are queried. Quick check for few demodulator drivers reveals there is
a lot of different error codes used in such case currently, few to
mention still: EOPNOTSUPP, ENOSYS, EAGAIN ... Lets try harmonize.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the Tobi/Overo board to the list of supported platforms.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Many regulators support a bypass mode where they simply switch their
input supply to the output. This is mainly used in low power retention
states where power consumption is extremely low so higher voltage or
less clean supplies can be used.
Support this by providing ops for the drivers and a consumer API which
allows the device to be put into bypass mode if all consumers enable it
and the machine enables permission for this.
This is not supported as a mode since the existing modes are rarely used
due to fuzzy definition and mostly redundant with modern hardware which is
able to respond promptly to load changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Graeme Gregory <gg@slimlogic.co.uk>
It adds a generic cpufreq driver for CPU0 frequency management based on
clk, regulator, OPP and device tree support. It can support both
uniprocessor (UP) and those symmetric multiprocessor (SMP) systems which
share clock and voltage across all CPUs.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
With a lot of devices booting from device tree nowadays, it requires
that OPP table can be initialized from device tree. The patch adds
a helper function of_init_opp_table together with a binding doc for
that purpose.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
One feature present in powernow-k8 that isn't present in acpi-cpufreq
is support for enabling or disabling AMD's core performance boost
technology. This patch adds support to acpi-cpufreq, but also
includes support for Intel's dynamic acceleration.
The original boost disabling sysfs file was per CPU, but acted
globally. Also the naming (cpb) was at least not intuitive.
So lets introduce a single file simply called "boost", which sits
once in /sys/devices/system/cpu/cpufreq.
This should be the only way of using this feature, so add
documentation about the rationale and the usage.
A following patch will re-introduce the cpb knob for compatibility
reasons on AMD CPUs.
Per-CPU boost switching is possible, but not trivial and is thus
postponed to a later patch series.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Now that we've got generic code for freeing bios allocated from bio
pools, this isn't needed anymore.
This patch also makes bio_free() static, since without bi_destructor
there should be no need for it to be called anywhere else.
bio_free() is now only called from bio_put, so we can refactor those a
bit - move some code from bio_put() to bio_free() and kill the redundant
bio->bi_next = NULL.
v5: Switch to BIO_KMALLOC_POOL ((void *)~0), per Boaz
v6: BIO_KMALLOC_POOL now NULL, drop bio_free's EXPORT_SYMBOL
v7: No #define BIO_KMALLOC_POOL anymore
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Unlike the IMA measurement policy, the appraise policy can not be dependent
on runtime process information, such as the task uid, as the 'security.ima'
xattr is written on file close and must be updated each time the file changes,
regardless of the current task uid.
This patch extends the policy language with 'fowner', defines an appraise
policy, which appraises all files owned by root, and defines 'ima_appraise_tcb',
a new boot command line option, to enable the appraise policy.
Changelog v3:
- separate the measure from the appraise rules in order to support measuring
without appraising and appraising without measuring.
- change appraisal default for filesystems without xattr support to fail
- update default appraise policy for cgroups
Changelog v1:
- don't appraise RAMFS (Dmitry Kasatkin)
- merged rest of "ima: ima_must_appraise_or_measure API change" commit
(Dmtiry Kasatkin)
ima_must_appraise_or_measure() called ima_match_policy twice, which
searched the policy for a matching rule. Once for a matching measurement
rule and subsequently for an appraisal rule. Searching the policy twice
is unnecessary overhead, which could be noticeable with a large policy.
The new version of ima_must_appraise_or_measure() does everything in a
single iteration using a new version of ima_match_policy(). It returns
IMA_MEASURE, IMA_APPRAISE mask.
With the use of action mask only one efficient matching function
is enough. Removed other specific versions of matching functions.
Changelog:
- change 'owner' to 'fowner' to conform to the new LSM conditions posted by
Roberto Sassu.
- fix calls to ima_log_string()
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
IMA currently maintains an integrity measurement list used to assert the
integrity of the running system to a third party. The IMA-appraisal
extension adds local integrity validation and enforcement of the
measurement against a "good" value stored as an extended attribute
'security.ima'. The initial methods for validating 'security.ima' are
hashed based, which provides file data integrity, and digital signature
based, which in addition to providing file data integrity, provides
authenticity.
This patch creates and maintains the 'security.ima' xattr, containing
the file data hash measurement. Protection of the xattr is provided by
EVM, if enabled and configured.
Based on policy, IMA calls evm_verifyxattr() to verify a file's metadata
integrity and, assuming success, compares the file's current hash value
with the one stored as an extended attribute in 'security.ima'.
Changelov v4:
- changed iint cache flags to hex values
Changelog v3:
- change appraisal default for filesystems without xattr support to fail
Changelog v2:
- fix audit msg 'res' value
- removed unused 'ima_appraise=' values
Changelog v1:
- removed unused iint mutex (Dmitry Kasatkin)
- setattr hook must not reset appraised (Dmitry Kasatkin)
- evm_verifyxattr() now differentiates between no 'security.evm' xattr
(INTEGRITY_NOLABEL) and no EVM 'protected' xattrs included in the
'security.evm' (INTEGRITY_NOXATTRS).
- replace hash_status with ima_status (Dmitry Kasatkin)
- re-initialize slab element ima_status on free (Dmitry Kasatkin)
- include 'security.ima' in EVM if CONFIG_IMA_APPRAISE, not CONFIG_IMA
- merged half "ima: ima_must_appraise_or_measure API change" (Dmitry Kasatkin)
- removed unnecessary error variable in process_measurement() (Dmitry Kasatkin)
- use ima_inode_post_setattr() stub function, if IMA_APPRAISE not configured
(moved ima_inode_post_setattr() to ima_appraise.c)
- make sure ima_collect_measurement() can read file
Changelog:
- add 'iint' to evm_verifyxattr() call (Dimitry Kasatkin)
- fix the race condition between chmod, which takes the i_mutex and then
iint->mutex, and ima_file_free() and process_measurement(), which take
the locks in the reverse order, by eliminating iint->mutex. (Dmitry Kasatkin)
- cleanup of ima_appraise_measurement() (Dmitry Kasatkin)
- changes as a result of the iint not allocated for all regular files, but
only for those measured/appraised.
- don't try to appraise new/empty files
- expanded ima_appraisal description in ima/Kconfig
- IMA appraise definitions required even if IMA_APPRAISE not enabled
- add return value to ima_must_appraise() stub
- unconditionally set status = INTEGRITY_PASS *after* testing status,
not before. (Found by Joe Perches)
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
EMIF - External Memory Interface - is an SDRAM controller used in
TI SoCs. EMIF supports, based on the IP revision, one or more of
DDR2/DDR3/LPDDR2 protocols. This binding describes a given instance
of the EMIF IP and memory parts attached to it.
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
[santosh.shilimkar@ti.com: Rebased against 3.6-rc]
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
device tree bindings for LPDDR2 SDRAM memories compliant
to JESD209-2 standard.
The 'lpddr2' binding in-turn uses another binding 'lpddr2-timings'
for specifying the AC timing parameters of the memory device at
different speed-bins.
Reviewed-by: Benoit Cousson <b-cousson@ti.com>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
[santosh.shilimkar@ti.com: Rebased against 3.6-rc]
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
With this patch we no longer reuse function tracer infrastructure, now
we register our own tracer back-end via a debugfs knob.
It's a bit more code, but that is the only downside. On the bright side we
have:
- Ability to make persistent_ram module removable (when needed, we can
move ftrace_ops struct into a module). Note that persistent_ram is still
not removable for other reasons, but with this patch it's just one
thing less to worry about;
- Pstore part is more isolated from the generic function tracer. We tried
it already by registering our own tracer in available_tracers, but that
way we're loosing ability to see the traces while we record them to
pstore. This solution is somewhere in the middle: we only register
"internal ftracer" back-end, but not the "front-end";
- When there is only pstore tracing enabled, the kernel will only write
to the pstore buffer, omitting function tracer buffer (which, of course,
still can be enabled via 'echo function > current_tracer').
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
This patch adds,
- 4 G-Scaler devices to the DT device list
- G-Scaler specific entries to the machine file
- binding documentation for G-Scaler entries
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Until now the EXYNOS-SoC was the only Samsung-SoC supporting the GPIOs
via the device tree. This patch implements dt-support for the
s3c24xx arches.
The controllers contain only 3 cells, as the underlying gpio controller
does not support controlling the drive strength on a gpio level.
Tested with the gpio-keys driver on a s3c2416 based machine.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
[kgene.kim@samsung.com: fixed build error]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Pull PCI updates from Bjorn Helgaas:
"Power management
- PCI/PM: Enable D3/D3cold by default for most devices
- PCI/PM: Keep parent bridge active when probing device
- PCI/PM: Fix config reg access for D3cold and bridge suspending
- PCI/PM: Add ABI document for sysfs file d3cold_allowed
Core
- PCI: Don't print anything while decoding is disabled"
* tag '3.6-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Don't print anything while decoding is disabled
PCI/PM: Add ABI document for sysfs file d3cold_allowed
PCI/PM: Fix config reg access for D3cold and bridge suspending
PCI/PM: Keep parent bridge active when probing device
PCI/PM: Enable D3/D3cold by default for most devices
Update Samsung GPIO API documentation to reflect removal of
the s3c24xx specific gpio API. While at it, fix some typos.
The notes on conversion from s3c2410_* functions to the gpiolib
API are left here just in case there is any out of tree code that
still needs to be converted.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add a new device tree enabled pinctrl and gpiolib driver for Samsung
SoC's. This driver provides a common and extensible framework for all
Samsung SoC's to interface with the pinctrl and gpiolib subsystems. This
driver supports only device tree based instantiation and hence can be
used only on those Samsung platforms that have device tree enabled.
This driver is split into two parts: the pinctrl interface and the gpiolib
interface. The pinctrl interface registers pinctrl devices with the pinctrl
subsystem and gpiolib interface registers gpio chips with the gpiolib
subsystem. The information about the pins, pin groups, pin functions and
gpio chips, which are SoC specific, are parsed from device tree node.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
