Support for loading the twl4030 audio module via devicetree.
Sub devices for codec and vibra will be created as mfd devices once the
core MFD driver is loaded when the kernel is booted with a DT blob.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Allow low-level remoteproc drivers to report rproc crashes by exporting
a new rproc_report_crash() function (invoking this from non-rproc drivers
is probably wrong, and should be carefully scrutinized if ever needed).
rproc_report_crash() can be called from any context; it offloads the
tasks of handling the crash to a separate thread.
Handling the crash from a separate thread is helpful because:
- Ability to call invoke rproc_report_crash() from atomic context, due to
the fact that many crashes trigger an interrupt, so this function can be
called directly from ISR context.
- Avoiding deadlocks which could happen if rproc_report_crash() is called
from a function which indirectly holds the rproc lock.
Handling the crash might involve:
- Remoteproc register dump
- Remoteproc stack dump
- Remoteproc core dump
- Saving Remoteproc traces so they can be read after the crash
- Reseting the remoteproc in order to make it functional again (hard recovery)
Right now, we only print the crash type which was detected, and only the
mmufault type is supported. Remoteproc low-level drivers can add more types
when needed.
Signed-off-by: Fernando Guzman Lugo <fernando.lugo@ti.com>
[ohad: some commentary, white space and commit log changes]
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Every fabric driver has to supply a se_tfo->set_fabric_sense_len()
method, just so iSCSI can return an offset of 2. However, every fabric
driver is already allocating a sense buffer and passing it into the
target core, either via transport_init_se_cmd() or target_submit_cmd().
So instead of having iSCSI pass the start of its sense buffer into the
core and then later tell the core to skip the first 2 bytes, it seems
easier for iSCSI just to do the offset of 2 when it passes the sense
buffer into the core. Then we can drop the se_tfo->set_fabric_sense_len()
everywhere, and just add a couple of lines of code to iSCSI to set the
sense data length to the beginning of the buffer right before it sends
it over the network.
(nab: Remove .set_fabric_sense_len usage from tcm_qla2xxx_npiv_ops +
change transport_get_sense_buffer to follow v3.6-rc6 code w/o
->set_fabric_sense_len usage)
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
There are no callers of se_tfo->get_fabric_sense_len(), so we should
stop having every fabric driver implement it.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This is initial device tree support for the ARM Integrator family,
we create a very basic device tree, #ifdef out the non-DT machines
when compiling for device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* pm-cpufreq:
cpufreq: OMAP: remove loops_per_jiffy recalculate for smp
sections: fix section conflicts in drivers/cpufreq
cpufreq: conservative: update frequency when limits are relaxed
cpufreq / ondemand: update frequency when limits are relaxed
cpufreq: Add a generic cpufreq-cpu0 driver
PM / OPP: Initialize OPP table from device tree
ARM: add cpufreq transiton notifier to adjust loops_per_jiffy for smp
cpufreq: Remove support for hardware P-state chips from powernow-k8
acpi-cpufreq: Add compatibility for legacy AMD cpb sysfs knob
acpi-cpufreq: Add support for disabling dynamic overclocking
ACPI: Add fixups for AMD P-state figures
powernow-k8: delay info messages until initialization has succeeded
cpufreq: Add warning message to powernow-k8
acpi-cpufreq: Add quirk to disable _PSD usage on all AMD CPUs
acpi-cpufreq: Add support for modern AMD CPUs
cpufreq / powernow-k8: Fixup missing _PSS objects message
PM / cpufreq: Initialise the cpu field during conservative governor start
* pm-cpuidle:
ACPI / processor: remove pointless variable initialization
ACPI / processor: remove unused function parameter
cpuidle / ACPI : remove power from acpi_processor_cx structure
PM / cpuidle: Make ladder governor use the "disabled" state flag
Honor state disabling in the cpuidle ladder governor
- mention that system time needs to be added to wallclock time
- positive tsc_shift means left shift, not right
- mention additional 32bit right shift
Signed-off-by: Stefan Fritsch <sf@sfritsch.de>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch adds support for the two linux interfaces of the discard/TRIM
command for SSD devices and sparse/thinly-provisioned LUNs.
JFS will support batched discard via FITRIM ioctl and online discard
with the discard mount option.
Signed-off-by: Tino Reichardt <list-jfs@mcmilk.de>
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Add regmap based syscon driver.
This is usually used for access misc bits in registers which does not belong
to a specific module, for example, IMX IOMUXC GPR and ANATOP.
With this driver, client can use generic regmap API to access registers
which are registered into syscon.
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The MAX8907 is an I2C-based power-management IC containing voltage
regulators, a reset controller, a real-time clock, and a touch-screen
controller.
The original driver was written by:
* Gyungoh Yoo <jack.yoo@maxim-ic.com>
Various fixes and enhancements by:
* Jin Park <jinyoungp@nvidia.com>
* Tom Cherry <tcherry@nvidia.com>
* Prashant Gaikwad <pgaikwad@nvidia.com>
* Dan Willemsen <dwillemsen@nvidia.com>
* Laxman Dewangan <ldewangan@nvidia.com>
During upstreaming, I (swarren):
* Converted to regmap.
* Converted to regmap-irq.
* Allowed probing from device tree.
* Renamed from max8907c->max8907, since the driver covers at least the
C and B revisions.
* General cleanup.
Signed-off-by: Gyungoh Yoo <jack.yoo@maxim-ic.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com> #v3
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The virtual memory layout is described in
Documentation/arm64/memory.txt. This patch adds the MMU definitions for
the 4KB and 64KB translation table configurations. The SECTION_SIZE is
2MB with 4KB page and 512MB with 64KB page configuration.
PHYS_OFFSET is calculated at run-time and stored in a variable (no
run-time code patching at this stage).
On the current implementation, both user and kernel address spaces are
512G (39-bit) each with a maximum of 256G for the RAM linear mapping.
Linux uses 3 levels of translation tables with the 4K page configuration
and 2 levels with the 64K configuration. Extending the memory space
beyond 39-bit with the 4K pages or 42-bit with 64K pages requires an
additional level of translation tables.
The SPARSEMEM configuration is global to all AArch64 platforms and
allows for 1GB sections with SPARSEMEM_VMEMMAP enabled by default.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The patch adds the kernel booting and the initial setup code.
Documentation/arm64/booting.txt describes the booting protocol on the
AArch64 Linux kernel. This is subject to change following the work on
boot standardisation, ACPI.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The semantics of the interactions between GPIO and pinctrl may be
unclear, e.g. which one do you request first? This amends the
documentation to make this clear.
Reported-by: Domenico Andreoli <cavokz@gmail.com>
Acked-by: Domenico Andreoli <domenico.andreoli@linux.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This resolves the merge problems with:
drivers/usb/dwc3/gadget.c
drivers/usb/musb/tusb6010.c
that had been seen in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From Tony Lindgren:
From Paul Walmsley <paul@pwsan.com>:
AM33xx hwmod data and miscellaneous clock and hwmod fixes. AM33xx
should now boot on mainline after this is applied, according to
Vaibhav.
(The shortlog makes no sense here since it contains mostly the dependent
cleanups that are part of the preceding branches).
Signed-off-by: Olof Johansson <olof@lixom.net>
This part of the tty tree (unfortunately with all the preceding patches
as well) is a dependency for some of the OMAP cleanups, so we've pulled
it in as a dependency based on agreement with Greg.
Signed-off-by: Olof Johansson <olof@lixom.net>
From Tony Lindgren:
Remove the ancient omap specific atags that are no longer needed.
At some point we were planning to pass the bootloader information
with custom atags that did not work out too well.
There's no need for these any longer as the kernel has been booting
fine without them for quite some time. And Now we have device tree
support that can be used instead.
* tag 'cleanup-omap-tags-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: remove plat/board.h file
ARM: OMAP: move debug_card_init() function
ARM: OMAP1: move lcd pdata out of arch/arm/*
ARM: OMAP1: move omap1_bl pdata out of arch/arm/*
ARM: OMAP: remove the omap custom tags
ARM: OMAP1: remove the crystal type tag parsing
ARM: OMAP: remove the sti console workaround
ARM: OMAP: omap3evm: cleanup revision bits
ARM: OMAP: cleanup struct omap_board_config_kernel
+ sync to 3.6-rc5
Kevin Hilman <khilman@ti.com>:
Updates for omap_device layer for v3.7.
Allows omap_device layer to keep track of driver bound status in order
to make more intelligent decisions about idling unused devices.
* tag 'devel-omap-device-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: omap_device: idle devices with no driver bound
ARM: OMAP: omap_device: don't attempt late suspend if no driver bound
ARM: OMAP: omap_device: keep track of driver bound status
+ sync to 3.6-rc5
From Stephen Warren:
ARM: tegra: i2c driver enhancements mostly related to clocking
This branch contains a number of fixes and cleanups to the Tegra I2C
driver related to clocks. These are based on the common clock conversion
in order to avoid duplicating the clock driver changes before and after
the conversion. Finally, a bug-fix related to I2C_M_NOSTART is included.
This branch is based on previous pull request tegra-for-3.7-common-clk.
* tag 'tegra-for-3.7-drivers-i2c' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
i2c: tegra: dynamically control fast clk
i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
ARM: tegra: clock: remove unused clock entry for i2c
ARM: tegra: clock: add connection name in i2c clock entry
i2c: tegra: pass proper name for getting clock
ARM: tegra: clock: add i2c fast clock entry in clock table
ARM: Tegra: Add smp_twd clock for Tegra20
ARM: tegra: cpu-tegra: explicitly manage re-parenting
ARM: tegra: fix overflow in tegra20_pll_clk_round_rate()
ARM: tegra: Fix data type for io address
ARM: tegra: remove tegra_timer from tegra_list_clks
ARM: tegra30: clocks: fix the wrong tegra_audio_sync_clk_ops name
ARM: tegra: clocks: separate tegra_clk_32k_ops from Tegra20 and Tegra30
ARM: tegra: Remove duplicate code
ARM: tegra: Port tegra to generic clock framework
ARM: tegra: Add clk_tegra structure and helper functions
ARM: tegra: Rename tegra20 clock file
ARM: tegra20: Separate out clk ops and clk data
ARM: tegra30: Separate out clk ops and clk data
ARM: tegra: fix U16 divider range check
...
+ sync to v3.6-rc4
Resolved remove/modify conflict in arch/arm/mach-sa1100/leds-hackkit.c
caused by the sync with v3.6-rc4.
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull in a dependent branch from Mark Brown's regulator tree for the tegra/cleanup branch.
* depends/tps6589x-dt:
regulator: tps6586x: add support for SYS rail
From David Brown:
These patches migrate both the 8660 and 8960 targets on msm to be
devicetree only. This also sets most of the frame in place necessary
to build both targets into the same image.
There's a couple of cleanups in here that are kept in this series
because they are intimately tied to the changes necessary to support
the devicetree conversions.
By Stephen Boyd
via David Brown
* tag 'msm-dt-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
ARM: msm: Remove non-DT targets from 8960
ARM: msm: Add DT support for 8960
ARM: msm: Move io mapping prototypes to common.h
ARM: msm: Rename board-msm8x60 to signify its DT only status
ARM: msm: Make 8660 a DT only target
ARM: msm: Move 8660 to DT timer
ARM: msm: Add DT support to msm_timer
ARM: msm: Allow timer.c to compile on multiple targets
ARM: msm: Don't touch GIC registers outside of GIC code
ARM: msm: Add msm8660-surf.dts to Makefile.boot
ARM: msm: Add handle_irq handler for 8660 DT machine
Resolved trivial context conflict in arch/arm/mach-msm/io.c and a
remove/change conflict in arch/arm/mach-msm/board-msm8x60.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
This pulls in the staging tree fixes in 3.6-rc6 into our branch to resolve the
merge issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This branch contains changes needed to make omap2+
work properly with sparse IRQ. It also removes
dependencies to mach/hardware.h. These help moving
things towards ARM single zImage support.
This branch is based on a commit in tty-next
branch with omap-devel-gpmc-fixed-for-v3.7 and
cleanup-omap-tags-for-v3.7 merged in to keep things
compiling and sort out some merge conflicts.
Conflicts:
arch/arm/mach-omap2/omap4-common.c
drivers/gpio/gpio-twl4030.c
Conflicts:
net/netfilter/nfnetlink_log.c
net/netfilter/xt_LOG.c
Rather easy conflict resolution, the 'net' tree had bug fixes to make
sure we checked if a socket is a time-wait one or not and elide the
logging code if so.
Whereas on the 'net-next' side we are calculating the UID and GID from
the creds using different interfaces due to the user namespace changes
from Eric Biederman.
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux 3.6-rc5
* tag 'v3.6-rc5': (334 commits)
Linux 3.6-rc5
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
Remove user-triggerable BUG from mpol_to_str
xen/pciback: Fix proper FLR steps.
uml: fix compile error in deliver_alarm()
dj: memory scribble in logi_dj
Fix order of arguments to compat_put_time[spec|val]
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
powerpc: Don't use __put_user() in patch_instruction
powerpc: Make sure IPI handlers see data written by IPI senders
powerpc: Restore correct DSCR in context switch
powerpc: Fix DSCR inheritance in copy_thread()
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
powerpc: Update DSCR on all CPUs when writing sysfs dscr_default
powerpc/powernv: Always go into nap mode when CPU is offline
powerpc: Give hypervisor decrementer interrupts their own handler
powerpc/vphn: Fix arch_update_cpu_topology() return value
ARM: gemini: fix the gemini build
...
The device limit of 128 tape drives was established in 2003 as a
significant increase from the 8 tape drives allowed previously.
We're seeing customer sites that between a large number of drives
and multipath are discovering more than 128 devices and running
into problems.
Now that we're not stuck having to store a pointer in array
and aren't limited by kmalloc failing on higher order allocs we can
lift the limit to fill the entire minor range based on the number
of modes.
Based on the current code, that's 2^17 devices.
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
IFM O2D cameras use special sensor bus interface glue-logic to
connect camera sensors to mpc5200 LocalPlus bus. Add device tree
bindings documentation for it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add DT property "ti,system-power-controller" telling whether or not this
pmic is in charge of controlling the system power, so the power off
routine can be hooked up to system call "pm_power_off".
Based on the work by:
Dan Willemsen <dwillemsen@nvidia.com>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add DT property "ti,system-power-controller" telling whether or not this
pmic is in charge of controlling the system power, so the power off
routine can be hooked up to system call "pm_power_off".
Based on the work by:
Dan Willemsen <dwillemsen@nvidia.com>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
changeset 1248c7cb66 broke html compilation:
Documentation/DocBook/v4l2.xml:584: parser error : Entity 'sub-subdev-g-edid' not defined
Documentation/DocBook/v4l2.xml:626: parser error : chunk is not well balanced
Documentation/DocBook/media_api.xml:74: parser error : Failure to process entity sub-v4l2
Documentation/DocBook/media_api.xml:74: parser error : Entity 'sub-v4l2' not defined
I suspect that one file was simply missed at the patch. Yet, keeping
it broken is a very bad idea, so we should either remove the broken
patch or to remove just the invalid include. Let's take the latter
approach.
Due to that, a warning is now produced:
Error: no ID for constraint linkend: v4l2-subdev-edid.
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds an 'audit' policy action which audit logs file measurements.
Changelog v6:
- use new action flag handling (Dmitry Kasatkin).
- removed whitespace (Mimi)
Changelog v5:
- use audit_log_untrustedstring.
Changelog v4:
- cleanup digest -> hash conversion.
- use filename rather than d_path in ima_audit_measurement.
Changelog v3:
- Use newly exported audit_log_task_info for logging pid/ppid/uid/etc.
- Update the ima_policy ABI documentation.
Changelog v2:
- Use 'audit' action rather than 'measure_and_audit' to permit
auditing in the absence of measuring..
Changelog v1:
- Initial posting.
Signed-off-by: Peter Moody <pmoody@google.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Add support to setup the MSM timer via information obtained from
the devicetree.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[davidb@codeaurora.org: Remove leading zeros]
Signed-off-by: David Brown <davidb@codeaurora.org>
While reading through Documentation/cgroups/cgroups.txt, I found a
number of minor wordos and typos. The patch below is a conservative
handling of some of these: it provides just a number of "obviously
correct" fixes to the English that improve the readability
of the document somewhat. Obviously some more significant
fixes could be made to the document, but some of those
may not be in the "obviously correct" category.
Signed-off-by: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
* commit 'v3.6-rc5': (1098 commits)
Linux 3.6-rc5
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
Remove user-triggerable BUG from mpol_to_str
xen/pciback: Fix proper FLR steps.
uml: fix compile error in deliver_alarm()
dj: memory scribble in logi_dj
Fix order of arguments to compat_put_time[spec|val]
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
powerpc: Don't use __put_user() in patch_instruction
powerpc: Make sure IPI handlers see data written by IPI senders
powerpc: Restore correct DSCR in context switch
powerpc: Fix DSCR inheritance in copy_thread()
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
powerpc: Update DSCR on all CPUs when writing sysfs dscr_default
powerpc/powernv: Always go into nap mode when CPU is offline
powerpc: Give hypervisor decrementer interrupts their own handler
powerpc/vphn: Fix arch_update_cpu_topology() return value
ARM: gemini: fix the gemini build
...
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
drivers/rapidio/devices/tsi721.c
Set the default value of position_fix -1, and allow user passing
position_fix=0 explicitly to set the "auto" position-fix mode.
Otherwise the auto mode may be switched to others like COMBO of
VIACOMBO when the controller prefers it, thus user can't set the auto
mode any longer.
Also updated the documentation appropriately, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Give the key type the opportunity to preparse the payload prior to the
instantiation and update routines being called. This is done with the
provision of two new key type operations:
int (*preparse)(struct key_preparsed_payload *prep);
void (*free_preparse)(struct key_preparsed_payload *prep);
If the first operation is present, then it is called before key creation (in
the add/update case) or before the key semaphore is taken (in the update and
instantiate cases). The second operation is called to clean up if the first
was called.
preparse() is given the opportunity to fill in the following structure:
struct key_preparsed_payload {
char *description;
void *type_data[2];
void *payload;
const void *data;
size_t datalen;
size_t quotalen;
};
Before the preparser is called, the first three fields will have been cleared,
the payload pointer and size will be stored in data and datalen and the default
quota size from the key_type struct will be stored into quotalen.
The preparser may parse the payload in any way it likes and may store data in
the type_data[] and payload fields for use by the instantiate() and update()
ops.
The preparser may also propose a description for the key by attaching it as a
string to the description field. This can be used by passing a NULL or ""
description to the add_key() system call or the key_create_or_update()
function. This cannot work with request_key() as that required the description
to tell the upcall about the key to be created.
This, for example permits keys that store PGP public keys to generate their own
name from the user ID and public key fingerprint in the key.
The instantiate() and update() operations are then modified to look like this:
int (*instantiate)(struct key *key, struct key_preparsed_payload *prep);
int (*update)(struct key *key, struct key_preparsed_payload *prep);
and the new payload data is passed in *prep, whether or not it was preparsed.
Signed-off-by: David Howells <dhowells@redhat.com>
