Patch splits up the blowfish crypto routine into a common part (key setup)
which will be used by blowfish crypto modules (x86_64 assembly and generic-c).
Also fixes errors/warnings reported by checkpatch.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add SFF-8485 v0.7 / SAS-1 smp-write-gpio register support to libsas.
Defer SAS-2 support unless/until it defines an sgpio interface.
Minimum implementation needed to get the lights blinking.
try_test_sas_gpio_gp_bit() provides a common method to parse the
incoming write data (raw bitstream), and the to_sas_gpio_gp_bit() helper
routine can be used as a basis for the set/clear operations for the
'read' implementation. Host implementations parse as many bits
(ODx.[012]) as are locally supported and report the number of registers
successfully written. If the submitted data overruns the internal
number of registers available report the write as a success with the
number of bytes remaining reported in ->resid_len.
Example (assuming an active backplane) set the "identify" pattern for
the first 21 devices:
smp_write_gpio --count=2 --data=92,49,24,92,24,92,49,24 -t 4 --index=1 /dev/bsg/sas_hostX
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler
returns with interrupts enabled (see commit [b738a50a:
genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ELD (EDID-Like Data) describes to the HDMI/DP audio driver the audio
capabilities of the plugged monitor.
This adds drm_edid_to_eld() for converting EDID to ELD. The converted
ELD will be saved in a new drm_connector.eld[128] data field. This is
necessary because the graphics driver will need to fixup some of the
data fields (eg. HDMI/DP connection type, AV sync delay) before writing
to the hardware ELD buffer. drm_av_sync_delay() will help the graphics
drivers dynamically compute the AV sync delay for fixing-up the ELD.
ELD selection policy: it's possible for one encoder to be associated
with multiple connectors (ie. monitors), in which case the first found
ELD will be returned by drm_select_eld(). This policy may not be
suitable for all users, but let's start it simple first.
The impact of ELD selection policy: assume there are two monitors, one
supports stereo playback and the other has 8-channel output; cloned
display mode is used, so that the two monitors are associated with the
same internal encoder. If only the stereo playback capability is reported,
the user won't be able to start 8-channel playback; if the 8-channel ELD
is reported, then user space applications may send 8-channel samples
down, however the user may actually be listening to the 2-channel
monitor and not connecting speakers to the 8-channel monitor.
According to James, many TVs will either refuse the display anything or
pop-up an OSD warning whenever they receive hdmi audio which they cannot
handle. Eventually we will require configurability and/or per-monitor
audio control even when the video is cloned.
CC: Zhao Yakui <yakui.zhao@intel.com>
CC: Wang Zhenyu <zhenyu.z.wang@intel.com>
CC: Jeremy Bush <contractfrombelow@gmail.com>
CC: Christopher White <c.white@pulseforce.com>
CC: Pierre-Louis Bossart <pierre-louis.bossart@intel.com>
CC: Paul Menzel <paulepanter@users.sourceforge.net>
CC: James Cloos <cloos@jhcloos.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
* 'for-linus' of git://git.kernel.dk/linux-block:
floppy: use del_timer_sync() in init cleanup
blk-cgroup: be able to remove the record of unplugged device
block: Don't check QUEUE_FLAG_SAME_COMP in __blk_complete_request
mm: Add comment explaining task state setting in bdi_forker_thread()
mm: Cleanup clearing of BDI_pending bit in bdi_forker_thread()
block: simplify force plug flush code a little bit
block: change force plug flush call order
block: Fix queue_flag update when rq_affinity goes from 2 to 1
block: separate priority boosting from REQ_META
block: remove READ_META and WRITE_META
xen-blkback: fixed indentation and comments
xen-blkback: Don't disconnect backend until state switched to XenbusStateClosed.
The MT9T001 is a parallel 3MP sensor from Aptina (formerly Micron)
controlled through I2C.
The driver creates a V4L2 subdevice. It currently supports binning and
cropping, and the gain, exposure, test pattern and black level controls.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is now not needed as the sensor identification is done
through the media controller API.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hardware Spinlock devices usually contain numerous locks (known
devices today support between 32 to 256 locks).
Originally hwspinlock core required drivers to register (and later,
when needed, unregister) each lock separately.
That worked, but required hwspinlocks drivers to do a bit extra work
when they were probed/removed.
This patch changes hwspin_lock_{un}register() to allow a bank of
hwspinlocks to be {un}registered in a single invocation.
A new 'struct hwspinlock_device', which contains an array of 'struct
hwspinlock's is now being passed to the core upon registration (so
instead of wrapping each struct hwspinlock, a priv member has been added
to allow drivers to piggyback their private data with each hwspinlock).
While at it, several per-lock members were moved to be per-device:
1. struct device *dev
2. struct hwspinlock_ops *ops
In addition, now that the array of locks is handled by the core,
there's no reason to maintain a per-lock 'int id' member: the id of the
lock anyway equals to its index in the bank's array plus the bank's
base_id.
Remove this per-lock id member too, and instead use a simple pointers
arithmetic to derive it.
As a result of this change, hwspinlocks drivers are now simpler and smaller
(about %20 code reduction) and the memory footprint of the hwspinlock
framework is reduced.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
hwspinlock drivers must anyway select CONFIG_HWSPINLOCK,
so there's no point in having register/unregister stubs.
Removing those stubs will only make it easier for developers
to catch CONFIG_HWSPINLOCK mis-.config-urations.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
hwspinlock devices provide system-wide hardware locks that are used
by remote processors that have no other way to achieve synchronization.
To achieve that, each physical lock must have a system-wide id number
that is agreed upon, otherwise remote processors can't possibly assume
they're using the same hardware lock.
Usually boards have a single hwspinlock device, which provides several
hwspinlocks, and in this case, they can be trivially numbered 0 to
(num-of-locks - 1).
In case boards have several hwspinlocks devices, a different base id
should be used for each hwspinlock device (they can't all use 0 as
a starting id!).
While this is certainly not common, it's just plain wrong to just
silently use 0 as a base id whenever the hwspinlock driver is probed.
This patch provides a hwspinlock_pdata structure, that boards can use
to set a different base id for each of the hwspinlock devices they may
have, and demonstrates how to use it with the omap hwspinlock driver.
While we're at it, make sure the hwspinlock core prints an explicit
error message in case an hwspinlock is registered with an id number
that already exists; this will help users catch such base id issues.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Add management interface events for blocking/unblocking a device.
Sender of the block device command gets cmd complete and other
mgmt sockets get the event. Event is also sent to mgmt sockets when
blocking is done with ioctl, e.g when blocking a device with
hciconfig. This makes it possible for bluetoothd to track status
of blocked devices when a third party block or unblocks a device.
Event sending is handled in mgmt_device_blocked function which gets
called from hci_blacklist_add in hci_core.c. A pending command is
added in mgmt_block_device, so that it can found when sending the
event - the event is not sent to the socket from which the pending
command came. Locks were moved out from hci_core.c to hci_sock.c
and mgmt.c, because locking is needed also for mgmt_pending_add in
mgmt.c.
Signed-off-by: Antti Julku <antti.julku@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The function crypto_blkcipher_setkey() called by smp_e()
can sleep, so all the crypto work has to be moved to
hci_dev workqueue.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The objective is to make the core to have as little as possible
information about SMP procedures and logic. Now, all the SMP
specific information is hidden from the core.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Add command to management interface for enabling/disabling the
fast connectable mode.
Signed-off-by: Antti Julku <antti.julku@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
One piece of information that was lost when using the mgmt interface,
was the type of the connection. Using HCI events we used to know
the type of the connection based on the type of the event, e.g.
HCI_LE_Connection_Complete for LE links.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Add HCI_CONN_LE_SMP_PEND flag to indicate that SMP is pending
for that connection. This allows to have information that an SMP
procedure is going on for that connection.
We use the HCI_CONN_ENCRYPT_PEND to indicate that encryption
(HCI_LE_Start_Encryption) is pending for that connection.
While a SMP procedure is going on we hold an reference to the
connection, to avoid disconnections.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This checks if there is any existing connection according to its type
before start iterating in the list and immediately stop iterating when
reaching the number of connections.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The model_id is no longer needed within the platform_data
for the TPA driver since the model of TPA specified
with the device name (tpa6130a2/tpa6140a2).
Also update rx51 (the only affected user) to use the device name rather
than platform data.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The orginal code does not cover the case that one DAI such as codec
may be shared between other two DAIs(CPU).
When do symmetry checking, altough the codec DAI requires symmetry,
the two CPU DAIs may still be configured to run on different rates.
We change to check each DAI's state separately instead of only checking
the dai link to prevent this issue.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
One of the longest standing areas for improvement in ASoC has been the
DAPM algorithm - it repeats the same checks many times whenever it is run
and makes no effort to limit the areas of the graph it checks meaning we
do an awful lot of walks over the full graph. This has never mattered too
much as the size of the graph has generally been small in relation to the
size of the devices supported and the speed of CPUs but it is annoying.
In preparation for work on improving this insert a trace point after the
graph walk has been done. This gives us specific timing information for
the walk, and in order to give quantifiable (non-benchmark) numbers also
count every time we check a link or check the power for a widget and report
those numbers. Substantial changes in the algorithm may require tweaks to
the stats but they should be useful for simpler things.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The problem tackled in this patch is how to handle volatile autoclusters
correctly. A volatile autocluster is a cluster of related controls where one
control is the control that toggles between manual and auto mode and the other
controls are the values for the manual mode. For example autogain and gain,
autoexposure and exposure, etc.
If the hardware lets you read out the automatically calculated manual values
while in automode, then those manual controls should be marked volatile.
gain value as calculated by the autogain circuitry, then you would mark the
gain control as volatile (i.e. continuously changing).
The question in such use cases is what to do when switching from the auto
mode to the manual mode. Should we switch to the last set manual values or
should the volatile values be copied and used as the initial manual values.
For example: suppose the mode is manual gain and gain is set to 5. Then
autogain is turned on and the gain is set by the hardware to 2. Finally
the user switches back to manual gain. What should the gain be? 2 or 5?
After a long discussion the decisions was made to keep the last value as
calculated by the auto mode (so 2 in the example above).
The reason is that webcams that do such things will adapt themselves to
the current light conditions and when you switch back to manual mode you
expect that you keep the same picture. If you would switch back to old
manual values, then that would give you a suddenly different picture,
which is jarring for the user.
Additionally, this would be difficult to implement in applications that
store and restore the control values at application exit and start.
If you want to keep the old manual values when you switch from auto to
manual, then there would have to be a way for applications to get hold
of those old values while in auto mode, but there isn't.
So this patch will do all the heavy lifting in v4l2-ctrls.c: if you go
from auto mode to manual mode and the manual controls are volatile, then
g_volatile_ctrl will be called to get the current values for the manual
controls before switching to manual mode.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the new flag there is no need anymore to have a separate is_volatile
field. Modify all users to use the new flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a new VOLATILE control flag that is set for volatile controls.
That way applications know whether the value of the control is volatile
(i.e. can change continuously) or not.
Until now this was an internal property, but it is useful to know in
userspace as well.
A typical use case is the gain value when autogain is on. In that case the
hardware will continuously adjust the gain based various environmental
factors.
This patch just adds and documents the flag, it's not yet used.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The parameter's origin type is long. On an i386 architecture, it can
easily be larger than 0x80000000, causing this function to convert it
to a sign-extended u64 type.
Change the type to unsigned long so we get the correct result.
Signed-off-by: hank <pyu@redhat.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: <stable@kernel.org>
[ build fix ]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On the platforms which are x2apic and interrupt-remapping
capable, Linux kernel is enabling x2apic even if the BIOS
doesn't. This is to take advantage of the features that x2apic
brings in.
Some of the OEM platforms are running into issues because of
this, as their bios is not x2apic aware. For example, this was
resulting in interrupt migration issues on one of the platforms.
Also if the BIOS SMI handling uses APIC interface to send SMI's,
then the BIOS need to be aware of x2apic mode that OS has
enabled.
On some of these platforms, BIOS doesn't have a HW mechanism to
turnoff the x2apic feature to prevent OS from enabling it.
To resolve this mess, recent changes to the VT-d2 specification:
http://download.intel.com/technology/computing/vptech/Intel(r)_VT_for_Direct_IO.pdf
includes a mechanism that provides BIOS a way to request system
software to opt out of enabling x2apic mode.
Look at the x2apic optout flag in the DMAR tables before
enabling the x2apic mode in the platform. Also print a warning
that we have disabled x2apic based on the BIOS request.
Kernel boot parameter "intremap=no_x2apic_optout" can be used to
override the BIOS x2apic optout request.
Signed-off-by: Youquan Song <youquan.song@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: yinghai@kernel.org
Cc: joerg.roedel@amd.com
Cc: tony.luck@intel.com
Cc: dwmw2@infradead.org
Link: http://lkml.kernel.org/r/20110824001456.171766616@sbsiddha-desk.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Thus spake Andrew Morton:
"And I have the usual maintainability whine. If someone comes up to
vmscan.c and sees it calling blk_start_plug(), how are they supposed to
work out why that call is there? They go look at the blk_start_plug()
definition and it is undocumented. I think we can do better than this?"
Adapted from the LWN article - http://lwn.net/Articles/438256/ by Jens
Axboe and from an earlier attempt by Shaohua Li to document blk-plug.
[akpm@linux-foundation.org: grammatical and spelling tweaks]
Signed-off-by: Suresh Jayaraman <sjayaraman@suse.de>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@google.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
These functions can be used instead of referencing -EUCLEAN and -EBADMSG
all over the place. They should help make code a little bit more
readable.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
This patch clarifies a few bits of documentation in the header file
for the adxl34x driver.
Signed-off-by: Michael Tandy <lkml@mkt.me.uk>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
hex2bin converts a hexadecimal string to its binary representation.
The original version of hex2bin did not do any error checking. This
patch adds error checking and returns the result.
Changelog v1:
- removed unpack_hex_byte()
- changed return code from boolean to int
Changelog:
- use the new unpack_hex_byte()
- add __must_check compiler option (Andy Shevchenko's suggestion)
- change function API to return error checking result
(based on Tetsuo Handa's initial patch)
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Add IP6_TNL_F_USE_ORIG_FWMARK to ip6_tunnel, so that ip6_tnl_xmit2()
makes a route lookup taking into account skb->fwmark and doesnt cache
lookup result.
This permits more flexibility in policies and firewall setups.
To setup such a tunnel, "fwmark inherit" option should be added to "ip
-f inet6 tunnel" command.
Reported-by: Anders Franzen <Anders.Franzen@ericsson.com>
CC: Hans Schillström <hans.schillstrom@ericsson.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NFC Controller Interface (NCI) is a standard
communication protocol between an NFC Controller (NFCC)
and a Device Host (DH), defined by the NFC Forum.
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The file nfc.h was moved from include/net to include/net/nfc,
since new NFC header files will be added to include/net/nfc.
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add 2 new nfc control operations:
dev_up to turn on the nfc device
dev_down to turn off the nfc device
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
598841ca99 ([S390] use gmap address
spaces for kvm guest images) changed kvm on s390 to use a separate
address space for kvm guests. We can now put KVM guests anywhere
in the user address mode with a size up to 8PB - as long as the
memory is 1MB-aligned. This change was done without KVM extension
capability bit.
The change was added after 3.0, but we still have a chance to add
a feature bit before 3.1 (keeping the releases in a sane state).
We use number 71 to avoid collisions with other pending kvm patches
as requested by Alexander Graf.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Avi Kivity <avi@redhat.com>
Cc: Alexander Graf <agraf@suse.de>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
The WM5100 is a highly integrated low power audio subsystem with advanced
digital signal processing capabilities including effects, speech clarity
enhancement and active noise cancellation. This initial driver provides
support for basic audio paths, further patches will provide more
complete functionality.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
In systems where there is no hardware signal from the processor to the
PMIC to initiate the final power off sequence we must initiate the
shutdown with a register write to the PMIC. Support such systems in the
driver. Since this may prevent a full shutdown of the system platform
data is used to enable the feature.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'drm-nouveau-next' of git://git.freedesktop.org/git/nouveau/linux-2.6: (353 commits)
drm/nouveau: remove allocations from gart populate() hook
drm/nvc0/fb: slightly improve PMFB intr handling, move out of nvc0_graph.c
drm/nvc0/fifo: avoid touching missing subfifos
drm/nvd9/disp: bail out of mode_set_base if no fb bound to crtc
drm/nvd9/disp: stub some more api hooks so we don't oops on resume
drm/nouveau: fix printk typo in ioremap failure path
drm/nvc0/pm: minor clock readback fixes
drm/nv40/pm: execute memory reset script from vbios
drm/nv50/gr: refactor initialisation
drm/nouveau: if requested, try harder at disabling sysmem pushbufs
drm/nv50/gr: enable ctxprog xfer only when we need it to save power
drm/nouveau/dp: add support for displayport table 0x30
drm/nouveau/dp: return master dp table pointer too when looking up encoder
drm/nouveau/bios: simplify U/d table hash matching func to just match
drm/nouveau/dp: preserve non-pattern bits in DP_TRAINING_PATTERN_SET
drm/nvc0/gr: remove MODULE_FIRMWARE() lines
drm/nouveau/dp: use alternate lane mask for nvaf
drm/nouveau/dp: link rate scripts are selected with a comparison table
drm/nv40/pm: write nv40-specific reclocking routines
drm/nv40/pm: parse geometric delta clock from vbios
...
Add a helper function to allow drivers to disable hardware resampling
when the application has specified the SNDRV_PCM_HW_PARAMS_NORESAMPLE
flag.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We want to override the default value of SD_NODES_PER_DOMAIN on ppc64,
so move it into linux/topology.h.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
