regn divider is currently programmed to the registers without change,
but when calculating clock frequencies it is used as regn+1.
To make this similar to how DSI handles the dividers this patch changes
the regn value to be used as such for calculations, but the value
programmed to registers is regn-1.
This simplifies the clock frequency calculations, makes it similar to
DSI, and also allows us to use regn value 0 as undefined.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add initial support for DSI video mode panels:
- Add a new structure omap_dss_dsi_videomode_data in the member "panel" in
omap_dss_device struct. This allows panel driver to configure dsi video_mode
specific parameters.
- Configure basic DSI video mode timing parameters: HBP, HFP, HSA, VBP, VFP, VSA,
TL and VACT.
- Configure DSI protocol engine registers for video_mode support.
- Introduce functions dsi_video_mode_enable() and dsi_video_mode_disable() which
enable/disable video mode for a given virtual channel and a given pixel format
type.
Things left for later
- Add functions to check for errors in video mode timings provided by panel.
- Configure timing registers required for command mode interleaving.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently, DSI pixel info is only represented by the pixel size in bits using
the pixel_size parameter in omap_dss_device struct's ctrl member.
This is not sufficient information for DSI video mode usage, as two of the
supported formats(RGB666 loosely packed, and RGB888) have the same pixel
container size, but different data_type values for the video mode packet header.
Create enum "omap_dss_dsi_pixel_format" which describes the pixel data format
the panel is configured for. Create helper function dsi_get_pixel_size() which
returns the pixel size of the given pixel format.
Modify functions omapdss_default_get_recommended_bpp() and dss_use_replication()
to use dsi_get_pixel_size().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Introduce read functions which use generic Processor-to-Peripheral
transaction types. These are needed by some devices which may not support
corresponding DCS commands.
Add function dsi_vc_generic_send_read_request() which can send
a short packet with 0, 1 or 2 bytes of request data and the corresponding
generic data type.
Rename function dsi_vc_dcs_read_rx_fifo() to dsi_vc_read_rx_fifo() and modify
it to take the enum "dss_dsi_content_type" as an argument to use either DCS
or GENERIC Peripheral-to-Processor transaction types while parsing data read
from the device.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove functions dsi_vc_dcs_read_1() and dsi_vc_dcs_read_2(), these are used
when the panel is expected to return 1 and 2 bytes respecitvely. This was manily
used for debugging purposes. These functions should be implemented in the panel
driver if needed.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Intoduce enum "dss_dsi_content_type" to differentiate between DCS and generic
content types.
Introduce short and long packet write functions which use generic
Processor-to-Peripheral transaction types. These are needed by some devices
which may not support corresponding DCS commands. Create common write functions
which allow code reuse between DCS and generic write functions.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Create an enum for DSI operation modes, use this to set the capabilities of the
device in dsi_init_display().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add OMAP_DSS_OVL_CAP_GLOBAL_ALPHA and OMAP_DSS_OVL_CAP_PRE_MULT_ALPHA to
overlay capabilities. Use these instead of FEAT_GLOBAL_ALPHA,
FEAT_GLOBAL_ALPHA_VID1 and FEAT_PRE_MULT_ALPHA in code.
Remove FEAT_GLOBAL_ALPHA_VID1 and FEAT_PRE_MULT_ALPHA which are no
longer used. FEAT_GLOBAL_ALPHA is still used to decide if the HW has
global alpha register.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Archit Taneja <archit@ti.com>
Remove support for non-DISPC overlays and overlay managers.
The support to possibly have non-DISPC overlays and managers was made to
make it possible to use CPU and/or sDMA to update RFBI or DSI command
mode displays. It is ok to remove the support, because:
- No one has used the feature.
- Display update without DISPC is very slow, so it is debatable if the
update would even be usable.
- Removal cleans up code.
- If such a feature is needed later, it is better implemented outside
omapdss driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Archit Taneja <archit@ti.com>
Currently when changing the manager of an overlay, set_manager() directly
calls dispc to set the overlay's destination.
Change this to be more in line with other overlay configurations, and
this will also remove the need to have dispc clocks enabled when calling
set_manager().
A new field is added to overlay struct, "manager_changed". This is
similar to "display_changed" field in manager struct, and is used to
inform apply that the manager has changed and thus write to the
registers is needed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dsi_mux_pads() needs to know about the DSI HW module and the DSI lanes
used. Split the function into two, enable and disable, which take
necessary arguments, and add empty implementations for both.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
David reported:
Attached below is a watered-down version of rt/tst-cpuclock2.c from
GLIBC. Just build it with "gcc -o test test.c -lpthread -lrt" or
similar.
Run it several times, and you will see cases where the main thread
will measure a process clock difference before and after the nanosleep
which is smaller than the cpu-burner thread's individual thread clock
difference. This doesn't make any sense since the cpu-burner thread
is part of the top-level process's thread group.
I've reproduced this on both x86-64 and sparc64 (using both 32-bit and
64-bit binaries).
For example:
[davem@boricha build-x86_64-linux]$ ./test
process: before(0.001221967) after(0.498624371) diff(497402404)
thread: before(0.000081692) after(0.498316431) diff(498234739)
self: before(0.001223521) after(0.001240219) diff(16698)
[davem@boricha build-x86_64-linux]$
The diff of 'process' should always be >= the diff of 'thread'.
I make sure to wrap the 'thread' clock measurements the most tightly
around the nanosleep() call, and that the 'process' clock measurements
are the outer-most ones.
---
#include <unistd.h>
#include <stdio.h>
#include <stdlib.h>
#include <time.h>
#include <fcntl.h>
#include <string.h>
#include <errno.h>
#include <pthread.h>
static pthread_barrier_t barrier;
static void *chew_cpu(void *arg)
{
pthread_barrier_wait(&barrier);
while (1)
__asm__ __volatile__("" : : : "memory");
return NULL;
}
int main(void)
{
clockid_t process_clock, my_thread_clock, th_clock;
struct timespec process_before, process_after;
struct timespec me_before, me_after;
struct timespec th_before, th_after;
struct timespec sleeptime;
unsigned long diff;
pthread_t th;
int err;
err = clock_getcpuclockid(0, &process_clock);
if (err)
return 1;
err = pthread_getcpuclockid(pthread_self(), &my_thread_clock);
if (err)
return 1;
pthread_barrier_init(&barrier, NULL, 2);
err = pthread_create(&th, NULL, chew_cpu, NULL);
if (err)
return 1;
err = pthread_getcpuclockid(th, &th_clock);
if (err)
return 1;
pthread_barrier_wait(&barrier);
err = clock_gettime(process_clock, &process_before);
if (err)
return 1;
err = clock_gettime(my_thread_clock, &me_before);
if (err)
return 1;
err = clock_gettime(th_clock, &th_before);
if (err)
return 1;
sleeptime.tv_sec = 0;
sleeptime.tv_nsec = 500000000;
nanosleep(&sleeptime, NULL);
err = clock_gettime(th_clock, &th_after);
if (err)
return 1;
err = clock_gettime(my_thread_clock, &me_after);
if (err)
return 1;
err = clock_gettime(process_clock, &process_after);
if (err)
return 1;
diff = process_after.tv_nsec - process_before.tv_nsec;
printf("process: before(%lu.%.9lu) after(%lu.%.9lu) diff(%lu)\n",
process_before.tv_sec, process_before.tv_nsec,
process_after.tv_sec, process_after.tv_nsec, diff);
diff = th_after.tv_nsec - th_before.tv_nsec;
printf("thread: before(%lu.%.9lu) after(%lu.%.9lu) diff(%lu)\n",
th_before.tv_sec, th_before.tv_nsec,
th_after.tv_sec, th_after.tv_nsec, diff);
diff = me_after.tv_nsec - me_before.tv_nsec;
printf("self: before(%lu.%.9lu) after(%lu.%.9lu) diff(%lu)\n",
me_before.tv_sec, me_before.tv_nsec,
me_after.tv_sec, me_after.tv_nsec, diff);
return 0;
}
This is due to us using p->se.sum_exec_runtime in
thread_group_cputime() where we iterate the thread group and sum all
data. This does not take time since the last schedule operation (tick
or otherwise) into account. We can cure this by using
task_sched_runtime() at the cost of having to take locks.
This also means we can (and must) do away with
thread_group_sched_runtime() since the modified thread_group_cputime()
is now more accurate and would deadlock when called from
thread_group_sched_runtime().
Aside of that it makes the function safe on 32 bit systems. The old
code added t->se.sum_exec_runtime unprotected. sum_exec_runtime is a
64bit value and could be changed on another cpu at the same time.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: stable@kernel.org
Link: http://lkml.kernel.org/r/1314874459.7945.22.camel@twins
Tested-by: David Miller <davem@davemloft.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add a macro of_match_ptr() that allows the .of_match_table
entry in the driver structures to be assigned without having
an #ifdef xxx NULL for the case that OF is not enabled
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add to the dev_state and alloc_async structures the user namespace
corresponding to the uid and euid. Pass these to kill_pid_info_as_uid(),
which can then implement a proper, user-namespace-aware uid check.
Changelog:
Sep 20: Per Oleg's suggestion: Instead of caching and passing user namespace,
uid, and euid each separately, pass a struct cred.
Sep 26: Address Alan Stern's comments: don't define a struct cred at
usbdev_open(), and take and put a cred at async_completed() to
ensure it lasts for the duration of kill_pid_info_as_cred().
Signed-off-by: Serge Hallyn <serge.hallyn@canonical.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace calls to the Xen-specific xen_alloc_vm_area() and
xen_free_vm_area() functions with the generic equivalent
(alloc_vm_area() and free_vm_area()).
On x86, these were identical already.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Allow the xen balloon driver to populate its list of extra pages from
more than one region of memory. This will allow platforms to provide
(for example) a region of low memory and a region of high memory.
The maximum possible number of extra regions is 128 (== E820MAX) which
is quite large so xen_extra_mem is placed in __initdata. This is safe
as both xen_memory_setup() and balloon_init() are in __init.
The balloon regions themselves are not altered (i.e., there is still
only the one region).
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
In xen_memory_setup() pages that occur in gaps in the memory map are
released back to Xen. This reduces the domain's current page count in
the hypervisor. The Xen balloon driver does not correctly decrease
its initial current_pages count to reflect this. If 'delta' pages are
released and the target is adjusted the resulting reservation is
always 'delta' less than the requested target.
This affects dom0 if the initial allocation of pages overlaps the PCI
memory region but won't affect most domU guests that have been setup
with pseudo-physical memory maps that don't have gaps.
Fix this by accouting for the released pages when starting the balloon
driver.
If the domain's targets are managed by xapi, the domain may eventually
run out of memory and die because xapi currently gets its target
calculations wrong and whenever it is restarted it always reduces the
target by 'delta'.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
If we want to use granted pages for AIO, changing the mappings of a user
vma and the corresponding p2m is not enough, we also need to update the
kernel mappings accordingly.
Currently this is only needed for pages that are created for user usages
through /dev/xen/gntdev. As in, pages that have been in use by the
kernel and use the P2M will not need this special mapping.
However there are no guarantees that in the future the kernel won't
start accessing pages through the 1:1 even for internal usage.
In order to avoid the complexity of dealing with highmem, we allocated
the pages lowmem.
We issue a HYPERVISOR_grant_table_op right away in
m2p_add_override and we remove the mappings using another
HYPERVISOR_grant_table_op in m2p_remove_override.
Considering that m2p_add_override and m2p_remove_override are called
once per page we use multicalls and hypercall batching.
Use the kmap_op pointer directly as argument to do the mapping as it is
guaranteed to be present up until the unmapping is done.
Before issuing any unmapping multicalls, we need to make sure that the
mapping has already being done, because we need the kmap->handle to be
set correctly.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
[v1: Removed GRANT_FRAME_BIT usage]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Add an highmem parameter to alloc_xenballooned_pages, to allow callers to
request lowmem or highmem pages.
Fix the code style of free_xenballooned_pages' prototype.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Commit 7765be (Fix RCU_BOOST race handling current->rcu_read_unlock_special)
introduced a new ->rcu_boosted field in the task structure. This is
redundant because the existing ->rcu_boost_mutex will be non-NULL at
any time that ->rcu_boosted is nonzero. Therefore, this commit removes
->rcu_boosted and tests ->rcu_boost_mutex instead.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
We only need to constrain the compiler if we are actually exiting
the top-level RCU read-side critical section. This commit therefore
moves the first barrier() cal in __rcu_read_unlock() to inside the
"if" statement, thus avoiding needless register flushes for inner
rcu_read_unlock() calls.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The differences between rcu_assign_pointer() and RCU_INIT_POINTER() are
subtle, and it is easy to use the the cheaper RCU_INIT_POINTER() when
the more-expensive rcu_assign_pointer() should have been used instead.
The consequences of this mistake are quite severe.
This commit therefore carefully lays out the situations in which it it
permissible to use RCU_INIT_POINTER().
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Recent changes to gcc give warning messages on rcu_assign_pointers()'s
checks that allow it to determine when it is OK to omit the memory
barrier. Stephen Hemminger tried a number of gcc tricks to silence
this warning, but #pragmas and CPP macros do not work together in the
way that would be required to make this work.
However, we now have RCU_INIT_POINTER(), which already omits this
memory barrier, and which therefore may be used when assigning NULL to
an RCU-protected pointer that is accessible to readers. This commit
therefore makes rcu_assign_pointer() unconditionally emit the memory
barrier.
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
RCU no longer uses this global variable, nor does anyone else. This
commit therefore removes this variable. This reduces memory footprint
and also removes some atomic instructions and memory barriers from
the dyntick-idle path.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The rcu_dereference_bh_protected() and rcu_dereference_sched_protected()
macros are synonyms for rcu_dereference_protected() and are not used
anywhere in mainline. This commit therefore removes them.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Add trace events to record grace-period start and end, quiescent states,
CPUs noticing grace-period start and end, grace-period initialization,
call_rcu() invocation, tasks blocking in RCU read-side critical sections,
tasks exiting those same critical sections, force_quiescent_state()
detection of dyntick-idle and offline CPUs, CPUs entering and leaving
dyntick-idle mode (except from NMIs), CPUs coming online and going
offline, and CPUs being kicked for staying in dyntick-idle mode for too
long (as in many weeks, even on 32-bit systems).
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
rcu: Add the rcu flavor to callback trace events
The earlier trace events for registering RCU callbacks and for invoking
them did not include the RCU flavor (rcu_bh, rcu_preempt, or rcu_sched).
This commit adds the RCU flavor to those trace events.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This patch #ifdefs TINY_RCU kthreads out of the kernel unless RCU_BOOST=y,
thus eliminating context-switch overhead if RCU priority boosting has
not been configured.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Add event-trace markers to TREE_RCU kthreads to allow including these
kthread's CPU time in the utilization calculations.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Add a string to the rcu_batch_start() and rcu_batch_end() trace
messages that indicates the RCU type ("rcu_sched", "rcu_bh", or
"rcu_preempt"). The trace messages for the actual invocations
themselves are not marked, as it should be clear from the
rcu_batch_start() and rcu_batch_end() events before and after.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This commit adds the trace_rcu_utilization() marker that is to be
used to allow postprocessing scripts compute RCU's CPU utilization,
give or take event-trace overhead. Note that we do not include RCU's
dyntick-idle interface because event tracing requires RCU protection,
which is not available in dyntick-idle mode.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
There was recently some controversy about the overhead of invoking RCU
callbacks. Add TRACE_EVENT()s to obtain fine-grained timings for the
start and stop of a batch of callbacks and also for each callback invoked.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Pull the code that waits for an RCU grace period into a single function,
which is then called by synchronize_rcu() and friends in the case of
TREE_RCU and TREE_PREEMPT_RCU, and from rcu_barrier() and friends in
the case of TINY_RCU and TINY_PREEMPT_RCU.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Take a first step towards untangling Linux kernel header files by
placing the struct rcu_head definition into include/linux/types.h
and including include/linux/types.h in include/linux/rcupdate.h
where struct rcu_head used to be defined. The actual inclusion point
for include/linux/types.h is with the rest of the #include directives
rather than at the point where struct rcu_head used to be defined,
as suggested by Mathieu Desnoyers.
Once this is in place, then header files that need only rcu_head
can include types.h rather than rcupdate.h.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Long ago, using TREE_RCU with PREEMPT would result in "scheduling
while atomic" diagnostics if you blocked in an RCU read-side critical
section. However, PREEMPT now implies TREE_PREEMPT_RCU, which defeats
this diagnostic. This commit therefore adds a replacement diagnostic
based on PROVE_RCU.
Because rcu_lockdep_assert() and lockdep_rcu_dereference() are now being
used for things that have nothing to do with rcu_dereference(), rename
lockdep_rcu_dereference() to lockdep_rcu_suspicious() and add a third
argument that is a string indicating what is suspicious. This third
argument is passed in from a new third argument to rcu_lockdep_assert().
Update all calls to rcu_lockdep_assert() to add an informative third
argument.
Also, add a pair of rcu_lockdep_assert() calls from within
rcu_note_context_switch(), one complaining if a context switch occurs
in an RCU-bh read-side critical section and another complaining if a
context switch occurs in an RCU-sched read-side critical section.
These are present only if the PROVE_RCU kernel parameter is enabled.
Finally, fix some checkpatch whitespace complaints in lockdep.c.
Again, you must enable PROVE_RCU to see these new diagnostics. But you
are enabling PROVE_RCU to check out new RCU uses in any case, aren't you?
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The IEEE 1588 standard defines two kinds of messages, event and general
messages. Event messages require time stamping, and general do not. When
using UDP transport, two separate ports are used for the two message
types.
The BPF designed to recognize event messages incorrectly classifies L2
general messages as event messages. This commit fixes the issue by
extending the filter to check the message type field for L2 PTP packets.
Event messages are be distinguished from general messages by testing
the "general" bit.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Cc: <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an event to monitor comm value changes of tasks. Such an event
becomes vital, if someone desires to control threads of a process in
different manner.
A natural characteristic of threads is its comm value, and helpfully
application developers have an opportunity to change it in runtime.
Reporting about such events via proc connector allows to fine-grain
monitoring and control potentials, for instance a process control daemon
listening to proc connector and following comm value policies can place
specific threads to assigned cgroup partitions.
It might be possible to achieve a pale partial one-shot likeness without
this update, if an application changes comm value of a thread generator
task beforehand, then a new thread is cloned, and after that proc
connector listener gets the fork event and reads new thread's comm value
from procfs stat file, but this change visibly simplifies and extends the
matter.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 7361c36c52 (af_unix: Allow credentials to work across
user and pid namespaces) af_unix performance dropped a lot.
This is because we now take a reference on pid and cred in each write(),
and release them in read(), usually done from another process,
eventually from another cpu. This triggers false sharing.
# Events: 154K cycles
#
# Overhead Command Shared Object Symbol
# ........ ....... .................. .........................
#
10.40% hackbench [kernel.kallsyms] [k] put_pid
8.60% hackbench [kernel.kallsyms] [k] unix_stream_recvmsg
7.87% hackbench [kernel.kallsyms] [k] unix_stream_sendmsg
6.11% hackbench [kernel.kallsyms] [k] do_raw_spin_lock
4.95% hackbench [kernel.kallsyms] [k] unix_scm_to_skb
4.87% hackbench [kernel.kallsyms] [k] pid_nr_ns
4.34% hackbench [kernel.kallsyms] [k] cred_to_ucred
2.39% hackbench [kernel.kallsyms] [k] unix_destruct_scm
2.24% hackbench [kernel.kallsyms] [k] sub_preempt_count
1.75% hackbench [kernel.kallsyms] [k] fget_light
1.51% hackbench [kernel.kallsyms] [k]
__mutex_lock_interruptible_slowpath
1.42% hackbench [kernel.kallsyms] [k] sock_alloc_send_pskb
This patch includes SCM_CREDENTIALS information in a af_unix message/skb
only if requested by the sender, [man 7 unix for details how to include
ancillary data using sendmsg() system call]
Note: This might break buggy applications that expected SCM_CREDENTIAL
from an unaware write() system call, and receiver not using SO_PASSCRED
socket option.
If SOCK_PASSCRED is set on source or destination socket, we still
include credentials for mere write() syscalls.
Performance boost in hackbench : more than 50% gain on a 16 thread
machine (2 quad-core cpus, 2 threads per core)
hackbench 20 thread 2000
4.228 sec instead of 9.102 sec
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the TSC-40 serial touchscreen driver and should be
compatible with TSC-10 and TSC-25.
The driver was written by Linutronix on behalf of Bachmann electronic GmbH.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Export the default mmap function, snd_pcm_lib_default_mmap().
The upcoming non-snooping support in HD-audio driver will use this
to override the mmap method.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For almost all machines the DAI format is a constant, always set to the
same thing. This means that not only should we normally set it on init
rather than in hw_params() (where it has been for historical reasons) we
should also allow users to configure this by setting a variable in the
dai_link structure. The combination of these two will make many machine
drivers even more data driven.
Implement a new dai_fmt field in the dai_link doing just that. Since 0 is
a valid value for many format flags and we need to be able to tell if the
field is actually set also add one to all the values used to configure
formats.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use sk_buff fragment capabilities to link together incoming skbs
instead of allocating a new skb for reassembly and copying.
The new reassembly code works equally well for ERTM and streaming
mode, so there is now one reassembly function instead of two.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch introduces 3 trace points to prepare for tracing
rpm_idle/rpm_suspend/rpm_resume functions, so we can use these
trace points to replace the current dev_dbg().
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Correct comment errors, that mistake cpu partial objects number as pages
number, may make reader misunderstand.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Reviewed-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
tx params are currently configured per hw, although they
should be configured per interface.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever the scan request or tx_mgmt is requesting not to
use CCK rate for managemet frames through
NL80211_ATTR_TX_NO_CCK_RATE attribute, then mac80211 should
select appropriate least non-CCK rate. This could help to
send P2P probes and P2P action frames at non 11b rates
without diabling 11b rates globally.
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
