e160f7d430
At present devices use a simple integer offset to record the device tree node associated with the device. In preparation for supporting a live device tree, which uses a node pointer instead, refactor existing code to access this field through an inline function. Signed-off-by: Simon Glass <sjg@chromium.org>
579 lines
13 KiB
C
579 lines
13 KiB
C
/*
|
|
* Copyright (C) 2009 Texas Instruments Incorporated - http://www.ti.com/
|
|
*
|
|
* Driver for SPI controller on DaVinci. Based on atmel_spi.c
|
|
* by Atmel Corporation
|
|
*
|
|
* Copyright (C) 2007 Atmel Corporation
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <spi.h>
|
|
#include <malloc.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/hardware.h>
|
|
#include <dm.h>
|
|
|
|
/* SPIGCR0 */
|
|
#define SPIGCR0_SPIENA_MASK 0x1
|
|
#define SPIGCR0_SPIRST_MASK 0x0
|
|
|
|
/* SPIGCR0 */
|
|
#define SPIGCR1_CLKMOD_MASK BIT(1)
|
|
#define SPIGCR1_MASTER_MASK BIT(0)
|
|
#define SPIGCR1_SPIENA_MASK BIT(24)
|
|
|
|
/* SPIPC0 */
|
|
#define SPIPC0_DIFUN_MASK BIT(11) /* SIMO */
|
|
#define SPIPC0_DOFUN_MASK BIT(10) /* SOMI */
|
|
#define SPIPC0_CLKFUN_MASK BIT(9) /* CLK */
|
|
#define SPIPC0_EN0FUN_MASK BIT(0)
|
|
|
|
/* SPIFMT0 */
|
|
#define SPIFMT_SHIFTDIR_SHIFT 20
|
|
#define SPIFMT_POLARITY_SHIFT 17
|
|
#define SPIFMT_PHASE_SHIFT 16
|
|
#define SPIFMT_PRESCALE_SHIFT 8
|
|
|
|
/* SPIDAT1 */
|
|
#define SPIDAT1_CSHOLD_SHIFT 28
|
|
#define SPIDAT1_CSNR_SHIFT 16
|
|
|
|
/* SPIDELAY */
|
|
#define SPI_C2TDELAY_SHIFT 24
|
|
#define SPI_T2CDELAY_SHIFT 16
|
|
|
|
/* SPIBUF */
|
|
#define SPIBUF_RXEMPTY_MASK BIT(31)
|
|
#define SPIBUF_TXFULL_MASK BIT(29)
|
|
|
|
/* SPIDEF */
|
|
#define SPIDEF_CSDEF0_MASK BIT(0)
|
|
|
|
#ifndef CONFIG_DM_SPI
|
|
#define SPI0_BUS 0
|
|
#define SPI0_BASE CONFIG_SYS_SPI_BASE
|
|
/*
|
|
* Define default SPI0_NUM_CS as 1 for existing platforms that uses this
|
|
* driver. Platform can configure number of CS using CONFIG_SYS_SPI0_NUM_CS
|
|
* if more than one CS is supported and by defining CONFIG_SYS_SPI0.
|
|
*/
|
|
#ifndef CONFIG_SYS_SPI0
|
|
#define SPI0_NUM_CS 1
|
|
#else
|
|
#define SPI0_NUM_CS CONFIG_SYS_SPI0_NUM_CS
|
|
#endif
|
|
|
|
/*
|
|
* define CONFIG_SYS_SPI1 when platform has spi-1 device (bus #1) and
|
|
* CONFIG_SYS_SPI1_NUM_CS defines number of CS on this bus
|
|
*/
|
|
#ifdef CONFIG_SYS_SPI1
|
|
#define SPI1_BUS 1
|
|
#define SPI1_NUM_CS CONFIG_SYS_SPI1_NUM_CS
|
|
#define SPI1_BASE CONFIG_SYS_SPI1_BASE
|
|
#endif
|
|
|
|
/*
|
|
* define CONFIG_SYS_SPI2 when platform has spi-2 device (bus #2) and
|
|
* CONFIG_SYS_SPI2_NUM_CS defines number of CS on this bus
|
|
*/
|
|
#ifdef CONFIG_SYS_SPI2
|
|
#define SPI2_BUS 2
|
|
#define SPI2_NUM_CS CONFIG_SYS_SPI2_NUM_CS
|
|
#define SPI2_BASE CONFIG_SYS_SPI2_BASE
|
|
#endif
|
|
#endif
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
/* davinci spi register set */
|
|
struct davinci_spi_regs {
|
|
dv_reg gcr0; /* 0x00 */
|
|
dv_reg gcr1; /* 0x04 */
|
|
dv_reg int0; /* 0x08 */
|
|
dv_reg lvl; /* 0x0c */
|
|
dv_reg flg; /* 0x10 */
|
|
dv_reg pc0; /* 0x14 */
|
|
dv_reg pc1; /* 0x18 */
|
|
dv_reg pc2; /* 0x1c */
|
|
dv_reg pc3; /* 0x20 */
|
|
dv_reg pc4; /* 0x24 */
|
|
dv_reg pc5; /* 0x28 */
|
|
dv_reg rsvd[3];
|
|
dv_reg dat0; /* 0x38 */
|
|
dv_reg dat1; /* 0x3c */
|
|
dv_reg buf; /* 0x40 */
|
|
dv_reg emu; /* 0x44 */
|
|
dv_reg delay; /* 0x48 */
|
|
dv_reg def; /* 0x4c */
|
|
dv_reg fmt0; /* 0x50 */
|
|
dv_reg fmt1; /* 0x54 */
|
|
dv_reg fmt2; /* 0x58 */
|
|
dv_reg fmt3; /* 0x5c */
|
|
dv_reg intvec0; /* 0x60 */
|
|
dv_reg intvec1; /* 0x64 */
|
|
};
|
|
|
|
/* davinci spi slave */
|
|
struct davinci_spi_slave {
|
|
#ifndef CONFIG_DM_SPI
|
|
struct spi_slave slave;
|
|
#endif
|
|
struct davinci_spi_regs *regs;
|
|
unsigned int freq; /* current SPI bus frequency */
|
|
unsigned int mode; /* current SPI mode used */
|
|
u8 num_cs; /* total no. of CS available */
|
|
u8 cur_cs; /* CS of current slave */
|
|
bool half_duplex; /* true, if master is half-duplex only */
|
|
};
|
|
|
|
/*
|
|
* This functions needs to act like a macro to avoid pipeline reloads in the
|
|
* loops below. Use always_inline. This gains us about 160KiB/s and the bloat
|
|
* appears to be zero bytes (da830).
|
|
*/
|
|
__attribute__((always_inline))
|
|
static inline u32 davinci_spi_xfer_data(struct davinci_spi_slave *ds, u32 data)
|
|
{
|
|
u32 buf_reg_val;
|
|
|
|
/* send out data */
|
|
writel(data, &ds->regs->dat1);
|
|
|
|
/* wait for the data to clock in/out */
|
|
while ((buf_reg_val = readl(&ds->regs->buf)) & SPIBUF_RXEMPTY_MASK)
|
|
;
|
|
|
|
return buf_reg_val;
|
|
}
|
|
|
|
static int davinci_spi_read(struct davinci_spi_slave *ds, unsigned int len,
|
|
u8 *rxp, unsigned long flags)
|
|
{
|
|
unsigned int data1_reg_val;
|
|
|
|
/* enable CS hold, CS[n] and clear the data bits */
|
|
data1_reg_val = ((1 << SPIDAT1_CSHOLD_SHIFT) |
|
|
(ds->cur_cs << SPIDAT1_CSNR_SHIFT));
|
|
|
|
/* wait till TXFULL is deasserted */
|
|
while (readl(&ds->regs->buf) & SPIBUF_TXFULL_MASK)
|
|
;
|
|
|
|
/* preload the TX buffer to avoid clock starvation */
|
|
writel(data1_reg_val, &ds->regs->dat1);
|
|
|
|
/* keep reading 1 byte until only 1 byte left */
|
|
while ((len--) > 1)
|
|
*rxp++ = davinci_spi_xfer_data(ds, data1_reg_val);
|
|
|
|
/* clear CS hold when we reach the end */
|
|
if (flags & SPI_XFER_END)
|
|
data1_reg_val &= ~(1 << SPIDAT1_CSHOLD_SHIFT);
|
|
|
|
/* read the last byte */
|
|
*rxp = davinci_spi_xfer_data(ds, data1_reg_val);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int davinci_spi_write(struct davinci_spi_slave *ds, unsigned int len,
|
|
const u8 *txp, unsigned long flags)
|
|
{
|
|
unsigned int data1_reg_val;
|
|
|
|
/* enable CS hold and clear the data bits */
|
|
data1_reg_val = ((1 << SPIDAT1_CSHOLD_SHIFT) |
|
|
(ds->cur_cs << SPIDAT1_CSNR_SHIFT));
|
|
|
|
/* wait till TXFULL is deasserted */
|
|
while (readl(&ds->regs->buf) & SPIBUF_TXFULL_MASK)
|
|
;
|
|
|
|
/* preload the TX buffer to avoid clock starvation */
|
|
if (len > 2) {
|
|
writel(data1_reg_val | *txp++, &ds->regs->dat1);
|
|
len--;
|
|
}
|
|
|
|
/* keep writing 1 byte until only 1 byte left */
|
|
while ((len--) > 1)
|
|
davinci_spi_xfer_data(ds, data1_reg_val | *txp++);
|
|
|
|
/* clear CS hold when we reach the end */
|
|
if (flags & SPI_XFER_END)
|
|
data1_reg_val &= ~(1 << SPIDAT1_CSHOLD_SHIFT);
|
|
|
|
/* write the last byte */
|
|
davinci_spi_xfer_data(ds, data1_reg_val | *txp);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int davinci_spi_read_write(struct davinci_spi_slave *ds, unsigned
|
|
int len, u8 *rxp, const u8 *txp,
|
|
unsigned long flags)
|
|
{
|
|
unsigned int data1_reg_val;
|
|
|
|
/* enable CS hold and clear the data bits */
|
|
data1_reg_val = ((1 << SPIDAT1_CSHOLD_SHIFT) |
|
|
(ds->cur_cs << SPIDAT1_CSNR_SHIFT));
|
|
|
|
/* wait till TXFULL is deasserted */
|
|
while (readl(&ds->regs->buf) & SPIBUF_TXFULL_MASK)
|
|
;
|
|
|
|
/* keep reading and writing 1 byte until only 1 byte left */
|
|
while ((len--) > 1)
|
|
*rxp++ = davinci_spi_xfer_data(ds, data1_reg_val | *txp++);
|
|
|
|
/* clear CS hold when we reach the end */
|
|
if (flags & SPI_XFER_END)
|
|
data1_reg_val &= ~(1 << SPIDAT1_CSHOLD_SHIFT);
|
|
|
|
/* read and write the last byte */
|
|
*rxp = davinci_spi_xfer_data(ds, data1_reg_val | *txp);
|
|
|
|
return 0;
|
|
}
|
|
|
|
|
|
static int __davinci_spi_claim_bus(struct davinci_spi_slave *ds, int cs)
|
|
{
|
|
unsigned int mode = 0, scalar;
|
|
|
|
/* Enable the SPI hardware */
|
|
writel(SPIGCR0_SPIRST_MASK, &ds->regs->gcr0);
|
|
udelay(1000);
|
|
writel(SPIGCR0_SPIENA_MASK, &ds->regs->gcr0);
|
|
|
|
/* Set master mode, powered up and not activated */
|
|
writel(SPIGCR1_MASTER_MASK | SPIGCR1_CLKMOD_MASK, &ds->regs->gcr1);
|
|
|
|
/* CS, CLK, SIMO and SOMI are functional pins */
|
|
writel(((1 << cs) | SPIPC0_CLKFUN_MASK |
|
|
SPIPC0_DOFUN_MASK | SPIPC0_DIFUN_MASK), &ds->regs->pc0);
|
|
|
|
/* setup format */
|
|
scalar = ((CONFIG_SYS_SPI_CLK / ds->freq) - 1) & 0xFF;
|
|
|
|
/*
|
|
* Use following format:
|
|
* character length = 8,
|
|
* MSB shifted out first
|
|
*/
|
|
if (ds->mode & SPI_CPOL)
|
|
mode |= SPI_CPOL;
|
|
if (!(ds->mode & SPI_CPHA))
|
|
mode |= SPI_CPHA;
|
|
writel(8 | (scalar << SPIFMT_PRESCALE_SHIFT) |
|
|
(mode << SPIFMT_PHASE_SHIFT), &ds->regs->fmt0);
|
|
|
|
/*
|
|
* Including a minor delay. No science here. Should be good even with
|
|
* no delay
|
|
*/
|
|
writel((50 << SPI_C2TDELAY_SHIFT) |
|
|
(50 << SPI_T2CDELAY_SHIFT), &ds->regs->delay);
|
|
|
|
/* default chip select register */
|
|
writel(SPIDEF_CSDEF0_MASK, &ds->regs->def);
|
|
|
|
/* no interrupts */
|
|
writel(0, &ds->regs->int0);
|
|
writel(0, &ds->regs->lvl);
|
|
|
|
/* enable SPI */
|
|
writel((readl(&ds->regs->gcr1) | SPIGCR1_SPIENA_MASK), &ds->regs->gcr1);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int __davinci_spi_release_bus(struct davinci_spi_slave *ds)
|
|
{
|
|
/* Disable the SPI hardware */
|
|
writel(SPIGCR0_SPIRST_MASK, &ds->regs->gcr0);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int __davinci_spi_xfer(struct davinci_spi_slave *ds,
|
|
unsigned int bitlen, const void *dout, void *din,
|
|
unsigned long flags)
|
|
{
|
|
unsigned int len;
|
|
|
|
if (bitlen == 0)
|
|
/* Finish any previously submitted transfers */
|
|
goto out;
|
|
|
|
/*
|
|
* It's not clear how non-8-bit-aligned transfers are supposed to be
|
|
* represented as a stream of bytes...this is a limitation of
|
|
* the current SPI interface - here we terminate on receiving such a
|
|
* transfer request.
|
|
*/
|
|
if (bitlen % 8) {
|
|
/* Errors always terminate an ongoing transfer */
|
|
flags |= SPI_XFER_END;
|
|
goto out;
|
|
}
|
|
|
|
len = bitlen / 8;
|
|
|
|
if (!dout)
|
|
return davinci_spi_read(ds, len, din, flags);
|
|
if (!din)
|
|
return davinci_spi_write(ds, len, dout, flags);
|
|
if (!ds->half_duplex)
|
|
return davinci_spi_read_write(ds, len, din, dout, flags);
|
|
|
|
printf("SPI full duplex not supported\n");
|
|
flags |= SPI_XFER_END;
|
|
|
|
out:
|
|
if (flags & SPI_XFER_END) {
|
|
u8 dummy = 0;
|
|
davinci_spi_write(ds, 1, &dummy, flags);
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
#ifndef CONFIG_DM_SPI
|
|
|
|
static inline struct davinci_spi_slave *to_davinci_spi(struct spi_slave *slave)
|
|
{
|
|
return container_of(slave, struct davinci_spi_slave, slave);
|
|
}
|
|
|
|
int spi_cs_is_valid(unsigned int bus, unsigned int cs)
|
|
{
|
|
int ret = 0;
|
|
|
|
switch (bus) {
|
|
case SPI0_BUS:
|
|
if (cs < SPI0_NUM_CS)
|
|
ret = 1;
|
|
break;
|
|
#ifdef CONFIG_SYS_SPI1
|
|
case SPI1_BUS:
|
|
if (cs < SPI1_NUM_CS)
|
|
ret = 1;
|
|
break;
|
|
#endif
|
|
#ifdef CONFIG_SYS_SPI2
|
|
case SPI2_BUS:
|
|
if (cs < SPI2_NUM_CS)
|
|
ret = 1;
|
|
break;
|
|
#endif
|
|
default:
|
|
/* Invalid bus number. Do nothing */
|
|
break;
|
|
}
|
|
return ret;
|
|
}
|
|
|
|
void spi_cs_activate(struct spi_slave *slave)
|
|
{
|
|
/* do nothing */
|
|
}
|
|
|
|
void spi_cs_deactivate(struct spi_slave *slave)
|
|
{
|
|
/* do nothing */
|
|
}
|
|
|
|
void spi_init(void)
|
|
{
|
|
/* do nothing */
|
|
}
|
|
|
|
struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
|
|
unsigned int max_hz, unsigned int mode)
|
|
{
|
|
struct davinci_spi_slave *ds;
|
|
|
|
if (!spi_cs_is_valid(bus, cs))
|
|
return NULL;
|
|
|
|
ds = spi_alloc_slave(struct davinci_spi_slave, bus, cs);
|
|
if (!ds)
|
|
return NULL;
|
|
|
|
switch (bus) {
|
|
case SPI0_BUS:
|
|
ds->regs = (struct davinci_spi_regs *)SPI0_BASE;
|
|
break;
|
|
#ifdef CONFIG_SYS_SPI1
|
|
case SPI1_BUS:
|
|
ds->regs = (struct davinci_spi_regs *)SPI1_BASE;
|
|
break;
|
|
#endif
|
|
#ifdef CONFIG_SYS_SPI2
|
|
case SPI2_BUS:
|
|
ds->regs = (struct davinci_spi_regs *)SPI2_BASE;
|
|
break;
|
|
#endif
|
|
default: /* Invalid bus number */
|
|
return NULL;
|
|
}
|
|
|
|
ds->freq = max_hz;
|
|
ds->mode = mode;
|
|
|
|
return &ds->slave;
|
|
}
|
|
|
|
void spi_free_slave(struct spi_slave *slave)
|
|
{
|
|
struct davinci_spi_slave *ds = to_davinci_spi(slave);
|
|
|
|
free(ds);
|
|
}
|
|
|
|
int spi_xfer(struct spi_slave *slave, unsigned int bitlen,
|
|
const void *dout, void *din, unsigned long flags)
|
|
{
|
|
struct davinci_spi_slave *ds = to_davinci_spi(slave);
|
|
|
|
ds->cur_cs = slave->cs;
|
|
|
|
return __davinci_spi_xfer(ds, bitlen, dout, din, flags);
|
|
}
|
|
|
|
int spi_claim_bus(struct spi_slave *slave)
|
|
{
|
|
struct davinci_spi_slave *ds = to_davinci_spi(slave);
|
|
|
|
#ifdef CONFIG_SPI_HALF_DUPLEX
|
|
ds->half_duplex = true;
|
|
#else
|
|
ds->half_duplex = false;
|
|
#endif
|
|
return __davinci_spi_claim_bus(ds, ds->slave.cs);
|
|
}
|
|
|
|
void spi_release_bus(struct spi_slave *slave)
|
|
{
|
|
struct davinci_spi_slave *ds = to_davinci_spi(slave);
|
|
|
|
__davinci_spi_release_bus(ds);
|
|
}
|
|
|
|
#else
|
|
static int davinci_spi_set_speed(struct udevice *bus, uint max_hz)
|
|
{
|
|
struct davinci_spi_slave *ds = dev_get_priv(bus);
|
|
|
|
debug("%s speed %u\n", __func__, max_hz);
|
|
if (max_hz > CONFIG_SYS_SPI_CLK / 2)
|
|
return -EINVAL;
|
|
|
|
ds->freq = max_hz;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int davinci_spi_set_mode(struct udevice *bus, uint mode)
|
|
{
|
|
struct davinci_spi_slave *ds = dev_get_priv(bus);
|
|
|
|
debug("%s mode %u\n", __func__, mode);
|
|
ds->mode = mode;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int davinci_spi_claim_bus(struct udevice *dev)
|
|
{
|
|
struct dm_spi_slave_platdata *slave_plat =
|
|
dev_get_parent_platdata(dev);
|
|
struct udevice *bus = dev->parent;
|
|
struct davinci_spi_slave *ds = dev_get_priv(bus);
|
|
|
|
if (slave_plat->cs >= ds->num_cs) {
|
|
printf("Invalid SPI chipselect\n");
|
|
return -EINVAL;
|
|
}
|
|
ds->half_duplex = slave_plat->mode & SPI_PREAMBLE;
|
|
|
|
return __davinci_spi_claim_bus(ds, slave_plat->cs);
|
|
}
|
|
|
|
static int davinci_spi_release_bus(struct udevice *dev)
|
|
{
|
|
struct davinci_spi_slave *ds = dev_get_priv(dev->parent);
|
|
|
|
return __davinci_spi_release_bus(ds);
|
|
}
|
|
|
|
static int davinci_spi_xfer(struct udevice *dev, unsigned int bitlen,
|
|
const void *dout, void *din,
|
|
unsigned long flags)
|
|
{
|
|
struct dm_spi_slave_platdata *slave =
|
|
dev_get_parent_platdata(dev);
|
|
struct udevice *bus = dev->parent;
|
|
struct davinci_spi_slave *ds = dev_get_priv(bus);
|
|
|
|
if (slave->cs >= ds->num_cs) {
|
|
printf("Invalid SPI chipselect\n");
|
|
return -EINVAL;
|
|
}
|
|
ds->cur_cs = slave->cs;
|
|
|
|
return __davinci_spi_xfer(ds, bitlen, dout, din, flags);
|
|
}
|
|
|
|
static int davinci_spi_probe(struct udevice *bus)
|
|
{
|
|
/* Nothing to do */
|
|
return 0;
|
|
}
|
|
|
|
static int davinci_ofdata_to_platadata(struct udevice *bus)
|
|
{
|
|
struct davinci_spi_slave *ds = dev_get_priv(bus);
|
|
const void *blob = gd->fdt_blob;
|
|
int node = dev_of_offset(bus);
|
|
|
|
ds->regs = dev_map_physmem(bus, sizeof(struct davinci_spi_regs));
|
|
if (!ds->regs) {
|
|
printf("%s: could not map device address\n", __func__);
|
|
return -EINVAL;
|
|
}
|
|
ds->num_cs = fdtdec_get_int(blob, node, "num-cs", 4);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct dm_spi_ops davinci_spi_ops = {
|
|
.claim_bus = davinci_spi_claim_bus,
|
|
.release_bus = davinci_spi_release_bus,
|
|
.xfer = davinci_spi_xfer,
|
|
.set_speed = davinci_spi_set_speed,
|
|
.set_mode = davinci_spi_set_mode,
|
|
};
|
|
|
|
static const struct udevice_id davinci_spi_ids[] = {
|
|
{ .compatible = "ti,keystone-spi" },
|
|
{ .compatible = "ti,dm6441-spi" },
|
|
{ }
|
|
};
|
|
|
|
U_BOOT_DRIVER(davinci_spi) = {
|
|
.name = "davinci_spi",
|
|
.id = UCLASS_SPI,
|
|
.of_match = davinci_spi_ids,
|
|
.ops = &davinci_spi_ops,
|
|
.ofdata_to_platdata = davinci_ofdata_to_platadata,
|
|
.priv_auto_alloc_size = sizeof(struct davinci_spi_slave),
|
|
.probe = davinci_spi_probe,
|
|
};
|
|
#endif
|