970bf8603b
This converts the following to Kconfig: CONFIG_USE_BOOTCOMMAND CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND CONFIG_NFSBOOTCOMMAND Signed-off-by: Tom Rini <trini@konsulko.com>
97 lines
2.4 KiB
Plaintext
97 lines
2.4 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_SKIP_LOWLEVEL_INIT=y
|
|
CONFIG_ARCH_CPU_INIT=y
|
|
CONFIG_ARCH_AT91=y
|
|
CONFIG_SYS_TEXT_BASE=0x26f00000
|
|
CONFIG_SYS_MALLOC_F_LEN=0x2000
|
|
CONFIG_TARGET_SAMA5D3_XPLAINED=y
|
|
CONFIG_SPL_GPIO=y
|
|
CONFIG_SPL_LIBCOMMON_SUPPORT=y
|
|
CONFIG_SPL_LIBGENERIC_SUPPORT=y
|
|
CONFIG_NR_DRAM_BANKS=1
|
|
CONFIG_ENV_SIZE=0x4000
|
|
CONFIG_DM_GPIO=y
|
|
CONFIG_DEFAULT_DEVICE_TREE="at91-sama5d3_xplained"
|
|
CONFIG_SPL_TEXT_BASE=0x300000
|
|
CONFIG_SPL_MMC=y
|
|
CONFIG_SPL_SERIAL=y
|
|
CONFIG_SPL_DRIVERS_MISC=y
|
|
CONFIG_SPL=y
|
|
CONFIG_DEBUG_UART_BOARD_INIT=y
|
|
CONFIG_DEBUG_UART_BASE=0xffffee00
|
|
CONFIG_DEBUG_UART_CLOCK=132000000
|
|
CONFIG_SPL_FS_FAT=y
|
|
CONFIG_SPL_LIBDISK_SUPPORT=y
|
|
CONFIG_DEBUG_UART=y
|
|
CONFIG_ENV_VARS_UBOOT_CONFIG=y
|
|
CONFIG_SYS_LOAD_ADDR=0x22000000
|
|
CONFIG_FIT=y
|
|
CONFIG_SD_BOOT=y
|
|
CONFIG_BOOTDELAY=3
|
|
CONFIG_USE_BOOTARGS=y
|
|
CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk root=/dev/mmcblk0p2 rw rootwait"
|
|
CONFIG_USE_BOOTCOMMAND=y
|
|
CONFIG_BOOTCOMMAND="if test ! -n ${dtb_name}; then setenv dtb_name at91-${board_name}.dtb; fi; fatload mmc 0:1 0x21000000 ${dtb_name}; fatload mmc 0:1 0x22000000 zImage; bootz 0x22000000 - 0x21000000"
|
|
# CONFIG_DISPLAY_BOARDINFO is not set
|
|
CONFIG_HUSH_PARSER=y
|
|
CONFIG_CMD_BOOTZ=y
|
|
# CONFIG_CMD_FLASH is not set
|
|
# CONFIG_CMD_LOADS is not set
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_NAND=y
|
|
CONFIG_CMD_NAND_TRIMFFS=y
|
|
CONFIG_CMD_USB=y
|
|
CONFIG_CMD_DHCP=y
|
|
CONFIG_CMD_MII=y
|
|
CONFIG_CMD_PING=y
|
|
CONFIG_CMD_HASH=y
|
|
CONFIG_HASH_VERIFY=y
|
|
CONFIG_CMD_EXT4=y
|
|
CONFIG_CMD_EXT4_WRITE=y
|
|
CONFIG_CMD_FAT=y
|
|
CONFIG_CMD_FS_GENERIC=y
|
|
CONFIG_CMD_MTDPARTS=y
|
|
CONFIG_CMD_UBI=y
|
|
CONFIG_OF_CONTROL=y
|
|
CONFIG_SPL_OF_CONTROL=y
|
|
CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-parent dmas dma-names"
|
|
CONFIG_ENV_IS_IN_FAT=y
|
|
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
|
CONFIG_DM=y
|
|
CONFIG_SPL_DM=y
|
|
CONFIG_SPL_DM_SEQ_ALIAS=y
|
|
CONFIG_CLK=y
|
|
CONFIG_SPL_CLK=y
|
|
CONFIG_CLK_AT91=y
|
|
CONFIG_AT91_UTMI=y
|
|
CONFIG_AT91_H32MX=y
|
|
CONFIG_AT91_GPIO=y
|
|
CONFIG_GENERIC_ATMEL_MCI=y
|
|
CONFIG_MTD=y
|
|
CONFIG_MTD_RAW_NAND=y
|
|
CONFIG_NAND_ATMEL=y
|
|
CONFIG_ATMEL_NAND_HW_PMECC=y
|
|
CONFIG_PMECC_CAP=4
|
|
CONFIG_SYS_NAND_ONFI_DETECTION=y
|
|
CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y
|
|
CONFIG_SYS_NAND_U_BOOT_OFFS=0x40000
|
|
CONFIG_DM_ETH=y
|
|
CONFIG_MACB=y
|
|
CONFIG_PINCTRL=y
|
|
CONFIG_SPL_PINCTRL=y
|
|
CONFIG_PINCTRL_AT91=y
|
|
CONFIG_DM_SERIAL=y
|
|
CONFIG_DEBUG_UART_ANNOUNCE=y
|
|
CONFIG_ATMEL_USART=y
|
|
CONFIG_TIMER=y
|
|
CONFIG_SPL_TIMER=y
|
|
CONFIG_ATMEL_PIT_TIMER=y
|
|
CONFIG_USB=y
|
|
CONFIG_USB_EHCI_HCD=y
|
|
CONFIG_USB_STORAGE=y
|
|
CONFIG_W1=y
|
|
CONFIG_W1_GPIO=y
|
|
CONFIG_W1_EEPROM=y
|
|
CONFIG_W1_EEPROM_DS24XXX=y
|
|
CONFIG_OF_LIBFDT_OVERLAY=y
|