eaf6ea6a1d
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR - Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack pointer directly, otherwise we use the common calculation. - On some platforms that were using the standard calculation but did not set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them. - On a small number of platforms that were not subtracting GENERATED_GBL_DATA_SIZE do so now via the standard calculation. - CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most board config header files. Signed-off-by: Tom Rini <trini@konsulko.com>
39 lines
1.5 KiB
Plaintext
39 lines
1.5 KiB
Plaintext
CONFIG_ARM=y
|
|
# CONFIG_SYS_THUMB_BUILD is not set
|
|
CONFIG_ARCH_OMAP2PLUS=y
|
|
CONFIG_SYS_TEXT_BASE=0x80100000
|
|
CONFIG_SYS_MALLOC_LEN=0x120000
|
|
CONFIG_SYS_MALLOC_F_LEN=0x400
|
|
CONFIG_NR_DRAM_BANKS=2
|
|
CONFIG_SPL_TEXT_BASE=0x40200000
|
|
CONFIG_TARGET_SNIPER=y
|
|
CONFIG_SPL=y
|
|
CONFIG_DISTRO_DEFAULTS=y
|
|
CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
|
|
CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4020ff00
|
|
CONFIG_BOOTCOMMAND="setenv boot_mmc_part ${kernel_mmc_part}; if test reboot-${reboot-mode} = reboot-r; then echo recovery; setenv boot_mmc_part ${recovery_mmc_part}; fi; if test reboot-${reboot-mode} = reboot-b; then echo fastboot; fastboot 0; fi; part start mmc ${boot_mmc_dev} ${boot_mmc_part} boot_mmc_start; part size mmc ${boot_mmc_dev} ${boot_mmc_part} boot_mmc_size; mmc dev ${boot_mmc_dev}; mmc read ${kernel_addr_r} ${boot_mmc_start} ${boot_mmc_size} && bootm ${kernel_addr_r};"
|
|
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
|
|
CONFIG_SPL_MAX_SIZE=0xec00
|
|
# CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR is not set
|
|
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
|
|
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION=2
|
|
# CONFIG_SPL_FS_EXT4 is not set
|
|
# CONFIG_SPL_NAND_SUPPORT is not set
|
|
CONFIG_SYS_PROMPT="sniper # "
|
|
CONFIG_SYS_CBSIZE=512
|
|
CONFIG_SYS_PBSIZE=538
|
|
CONFIG_CMD_GPIO=y
|
|
CONFIG_CMD_I2C=y
|
|
CONFIG_CMD_MMC=y
|
|
# CONFIG_CMD_SETEXPR is not set
|
|
# CONFIG_CMD_NFS is not set
|
|
CONFIG_ENV_OVERWRITE=y
|
|
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
|
CONFIG_SYS_I2C_LEGACY=y
|
|
CONFIG_SPL_SYS_I2C_LEGACY=y
|
|
CONFIG_SYS_I2C_SPEED=400000
|
|
CONFIG_TWL4030_INPUT=y
|
|
CONFIG_MMC_OMAP_HS=y
|
|
CONFIG_CONS_INDEX=3
|
|
CONFIG_OF_LIBFDT=y
|