0613c36a7a
Perform a simple rename of CONFIG_EXTRA_ENV_SETTINGS to CFG_EXTRA_ENV_SETTINGS Signed-off-by: Tom Rini <trini@konsulko.com>
172 lines
5.3 KiB
C
172 lines
5.3 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* (C) Copyright 2008
|
|
* Sergei Poselenov, Emcraft Systems, sposelenov@emcraft.com.
|
|
*
|
|
* Wolfgang Denk <wd@denx.de>
|
|
* Copyright 2004 Freescale Semiconductor.
|
|
* (C) Copyright 2002,2003 Motorola,Inc.
|
|
* Xianghua Xiao <X.Xiao@motorola.com>
|
|
*/
|
|
|
|
/*
|
|
* Socrates
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* Only possible on E500 Version 2 or newer cores.
|
|
*/
|
|
|
|
/*
|
|
* sysclk for MPC85xx
|
|
*
|
|
* Two valid values are:
|
|
* 33000000
|
|
* 66000000
|
|
*
|
|
* Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz
|
|
* is likely the desired value here, so that is now the default.
|
|
* The board, however, can run at 66MHz. In any event, this value
|
|
* must match the settings of some switches. Details can be found
|
|
* in the README.mpc85xxads.
|
|
*/
|
|
|
|
#define CFG_SYS_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */
|
|
|
|
#undef CFG_SYS_DRAM_TEST /* memory test, takes time */
|
|
|
|
#define CFG_SYS_CCSRBAR 0xE0000000
|
|
#define CFG_SYS_CCSRBAR_PHYS_LOW CFG_SYS_CCSRBAR
|
|
|
|
/* DDR Setup */
|
|
#define CFG_SYS_DDR_SDRAM_BASE 0x00000000
|
|
#define CFG_SYS_SDRAM_BASE CFG_SYS_DDR_SDRAM_BASE
|
|
|
|
/* I2C addresses of SPD EEPROMs */
|
|
#define SPD_EEPROM_ADDRESS 0x50 /* CTLR 0 DIMM 0 */
|
|
|
|
|
|
/* Hardcoded values, to use instead of SPD */
|
|
#define CFG_SYS_DDR_CS0_BNDS 0x0000000f
|
|
#define CFG_SYS_DDR_CS0_CONFIG 0x80010102
|
|
#define CFG_SYS_DDR_TIMING_0 0x00260802
|
|
#define CFG_SYS_DDR_TIMING_1 0x3935D322
|
|
#define CFG_SYS_DDR_TIMING_2 0x14904CC8
|
|
#define CFG_SYS_DDR_MODE 0x00480432
|
|
#define CFG_SYS_DDR_INTERVAL 0x030C0100
|
|
#define CFG_SYS_DDR_CONFIG_2 0x04400000
|
|
#define CFG_SYS_DDR_CONFIG 0xC3008000
|
|
#define CFG_SYS_DDR_CLK_CONTROL 0x03800000
|
|
#define CFG_SYS_SDRAM_SIZE 256 /* in Megs */
|
|
|
|
/*
|
|
* Flash on the LocalBus
|
|
*/
|
|
#define CFG_SYS_FLASH0 0xFE000000
|
|
#define CFG_SYS_FLASH1 0xFC000000
|
|
#define CFG_SYS_FLASH_BANKS_LIST { CFG_SYS_FLASH1, CFG_SYS_FLASH0 }
|
|
|
|
#define CFG_SYS_LBC_FLASH_BASE CFG_SYS_FLASH1 /* Localbus flash start */
|
|
#define CFG_SYS_FLASH_BASE CFG_SYS_LBC_FLASH_BASE /* start of FLASH */
|
|
|
|
#define CFG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */
|
|
#define CFG_SYS_LBC_LBCR 0x00000000 /* LB config reg */
|
|
#define CFG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
|
|
#define CFG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer presc.*/
|
|
|
|
#define CFG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
|
|
#define CFG_SYS_INIT_RAM_SIZE 0x4000 /* Size used area in RAM*/
|
|
|
|
#define CFG_SYS_INIT_SP_OFFSET (CFG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
|
|
/* FPGA and NAND */
|
|
#define CFG_SYS_FPGA_BASE 0xc0000000
|
|
#define CFG_SYS_FPGA_SIZE 0x00100000 /* 1 MB */
|
|
|
|
#define CFG_SYS_NAND_BASE (CFG_SYS_FPGA_BASE + 0x70)
|
|
|
|
/* LIME GDC */
|
|
#define CFG_SYS_LIME_BASE 0xc8000000
|
|
|
|
/*
|
|
* General PCI
|
|
* Memory space is mapped 1-1.
|
|
*/
|
|
|
|
#define CFG_SYS_PCI1_MEM_PHYS 0x80000000
|
|
#define CFG_SYS_PCI1_IO_PHYS 0xE2000000
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CFG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
|
|
|
|
|
#define CFG_EXTRA_ENV_SETTINGS \
|
|
"netdev=eth0\0" \
|
|
"consdev=ttyS0\0" \
|
|
"uboot_file=/home/tftp/syscon3/u-boot.bin\0" \
|
|
"bootfile=/home/tftp/syscon3/uImage\0" \
|
|
"fdt_file=/home/tftp/syscon3/socrates.dtb\0" \
|
|
"initrd_file=/home/tftp/syscon3/uinitrd.gz\0" \
|
|
"uboot_addr=FFF60000\0" \
|
|
"kernel_addr=FE000000\0" \
|
|
"fdt_addr=FE1E0000\0" \
|
|
"ramdisk_addr=FE200000\0" \
|
|
"fdt_addr_r=B00000\0" \
|
|
"kernel_addr_r=200000\0" \
|
|
"ramdisk_addr_r=400000\0" \
|
|
"rootpath=/opt/eldk/ppc_85xxDP\0" \
|
|
"ramargs=setenv bootargs root=/dev/ram rw\0" \
|
|
"nfsargs=setenv bootargs root=/dev/nfs rw " \
|
|
"nfsroot=$serverip:$rootpath\0" \
|
|
"addcons=setenv bootargs $bootargs " \
|
|
"console=$consdev,$baudrate\0" \
|
|
"addip=setenv bootargs $bootargs " \
|
|
"ip=$ipaddr:$serverip:$gatewayip:$netmask" \
|
|
":$hostname:$netdev:off panic=1\0" \
|
|
"boot_nor=run ramargs addcons;" \
|
|
"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
|
|
"net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
|
|
"tftp ${fdt_addr_r} ${fdt_file}; " \
|
|
"run nfsargs addip addcons;" \
|
|
"bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
|
|
"update_uboot=tftp 100000 ${uboot_file};" \
|
|
"protect off fff60000 ffffffff;" \
|
|
"era fff60000 ffffffff;" \
|
|
"cp.b 100000 fff60000 ${filesize};" \
|
|
"setenv filesize;saveenv\0" \
|
|
"update_kernel=tftp 100000 ${bootfile};" \
|
|
"era fe000000 fe1dffff;" \
|
|
"cp.b 100000 fe000000 ${filesize};" \
|
|
"setenv filesize;saveenv\0" \
|
|
"update_fdt=tftp 100000 ${fdt_file};" \
|
|
"era fe1e0000 fe1fffff;" \
|
|
"cp.b 100000 fe1e0000 ${filesize};" \
|
|
"setenv filesize;saveenv\0" \
|
|
"update_initrd=tftp 100000 ${initrd_file};" \
|
|
"era fe200000 fe9fffff;" \
|
|
"cp.b 100000 fe200000 ${filesize};" \
|
|
"setenv filesize;saveenv\0" \
|
|
"clean_data=era fea00000 fff5ffff\0" \
|
|
"usbargs=setenv bootargs root=/dev/sda1 rw\0" \
|
|
"load_usb=usb start;" \
|
|
"ext2load usb 0:1 ${kernel_addr_r} /boot/uImage\0" \
|
|
"boot_usb=run load_usb usbargs addcons;" \
|
|
"bootm ${kernel_addr_r} - ${fdt_addr};" \
|
|
"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
|
|
""
|
|
|
|
/* pass open firmware flat tree */
|
|
|
|
#endif /* __CONFIG_H */
|