1a4596601f
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
149 lines
3.4 KiB
C
149 lines
3.4 KiB
C
/*
|
|
* (C) Copyright 2001-2004
|
|
* Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <asm/processor.h>
|
|
#include <asm/io.h>
|
|
#include <command.h>
|
|
#include <malloc.h>
|
|
#include <sja1000.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
extern void lxt971_no_sleep(void);
|
|
|
|
/*
|
|
* generate a short spike on the CAN tx line
|
|
* to bring the couplers in sync
|
|
*/
|
|
void init_coupler(u32 addr)
|
|
{
|
|
struct sja1000_basic_s *ctrl = (struct sja1000_basic_s *)addr;
|
|
|
|
/* reset */
|
|
out_8(&ctrl->cr, CR_RR);
|
|
|
|
/* dominant */
|
|
out_8(&ctrl->btr0, 0x00); /* btr setup is required */
|
|
out_8(&ctrl->btr1, 0x14); /* we use 1Mbit/s */
|
|
out_8(&ctrl->oc, OC_TP1 | OC_TN1 | OC_POL1 |
|
|
OC_TP0 | OC_TN0 | OC_POL0 | OC_MODE1);
|
|
out_8(&ctrl->cr, 0x00);
|
|
|
|
/* delay */
|
|
in_8(&ctrl->cr);
|
|
in_8(&ctrl->cr);
|
|
in_8(&ctrl->cr);
|
|
in_8(&ctrl->cr);
|
|
|
|
/* reset */
|
|
out_8(&ctrl->cr, CR_RR);
|
|
}
|
|
|
|
int board_early_init_f (void)
|
|
{
|
|
/*
|
|
* IRQ 0-15 405GP internally generated; active high; level sensitive
|
|
* IRQ 16 405GP internally generated; active low; level sensitive
|
|
* IRQ 17-24 RESERVED
|
|
* IRQ 25 (EXT IRQ 0) CAN0; active low; level sensitive
|
|
* IRQ 26 (EXT IRQ 1) SER0 ; active low; level sensitive
|
|
* IRQ 27 (EXT IRQ 2) SER1; active low; level sensitive
|
|
* IRQ 28 (EXT IRQ 3) FPGA 0; active low; level sensitive
|
|
* IRQ 29 (EXT IRQ 4) FPGA 1; active low; level sensitive
|
|
* IRQ 30 (EXT IRQ 5) PCI INTA; active low; level sensitive
|
|
* IRQ 31 (EXT IRQ 6) COMPACT FLASH; active high; level sensitive
|
|
*/
|
|
mtdcr(UIC0SR, 0xFFFFFFFF); /* clear all ints */
|
|
mtdcr(UIC0ER, 0x00000000); /* disable all ints */
|
|
mtdcr(UIC0CR, 0x00000000); /* set all to be non-critical*/
|
|
mtdcr(UIC0PR, 0xFFFFFF80); /* set int polarities */
|
|
mtdcr(UIC0TR, 0x10000000); /* set int trigger levels */
|
|
mtdcr(UIC0VCR, 0x00000001); /* set vect base=0,INT0 highest priority*/
|
|
mtdcr(UIC0SR, 0xFFFFFFFF); /* clear all ints */
|
|
|
|
/*
|
|
* EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
|
|
*/
|
|
mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
|
|
|
|
/*
|
|
* Reset CPLD via GPIO12 (CS3) pin
|
|
*/
|
|
out_be32((void *)GPIO0_OR,
|
|
in_be32((void *)GPIO0_OR) & ~(0x80000000 >> 12));
|
|
udelay(1000); /* wait 1ms */
|
|
out_be32((void *)GPIO0_OR,
|
|
in_be32((void *)GPIO0_OR) | (0x80000000 >> 12));
|
|
udelay(1000); /* wait 1ms */
|
|
|
|
return 0;
|
|
}
|
|
|
|
int misc_init_r (void)
|
|
{
|
|
/* adjust flash start and offset */
|
|
gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
|
|
gd->bd->bi_flashoffset = 0;
|
|
|
|
/*
|
|
* Init magnetic coupler
|
|
*/
|
|
if (!getenv("noinitcoupler"))
|
|
init_coupler(CAN_BA);
|
|
|
|
return (0);
|
|
}
|
|
|
|
/*
|
|
* Check Board Identity:
|
|
*/
|
|
int checkboard (void)
|
|
{
|
|
char str[64];
|
|
int i = getenv_f("serial#", str, sizeof(str));
|
|
int flashcnt;
|
|
int delay;
|
|
u8 *led_reg = (u8 *)(CAN_BA + 0x1000);
|
|
|
|
puts ("Board: ");
|
|
|
|
if (i == -1) {
|
|
puts ("### No HW ID - assuming VOM405");
|
|
} else {
|
|
puts(str);
|
|
}
|
|
|
|
printf(" (PLD-Version=%02d)\n", in_8(led_reg));
|
|
|
|
/*
|
|
* Flash LEDs
|
|
*/
|
|
for (flashcnt = 0; flashcnt < 3; flashcnt++) {
|
|
out_8(led_reg, 0x40); /* LED_B..D off */
|
|
for (delay = 0; delay < 100; delay++)
|
|
udelay(1000);
|
|
out_8(led_reg, 0x47); /* LED_B..D on */
|
|
for (delay = 0; delay < 50; delay++)
|
|
udelay(1000);
|
|
}
|
|
out_8(led_reg, 0x40);
|
|
|
|
return 0;
|
|
}
|
|
|
|
void reset_phy(void)
|
|
{
|
|
#ifdef CONFIG_LXT971_NO_SLEEP
|
|
|
|
/*
|
|
* Disable sleep mode in LXT971
|
|
*/
|
|
lxt971_no_sleep();
|
|
#endif
|
|
}
|