d52ebf1022
This patch supports mmc/sd card with spi interface. It is based on the generic mmc framework. It works with SDHC and supports multi blocks read/write. The crc checksum on data packet is enabled with the def, There is a subcomamnd "mmc_spi" to setup spi bus and cs at run time. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Andy Fleming <afleming@freescale.com>
281 lines
7.1 KiB
C
281 lines
7.1 KiB
C
/*
|
|
* generic mmc spi driver
|
|
*
|
|
* Copyright (C) 2010 Thomas Chou <thomas@wytron.com.tw>
|
|
* Licensed under the GPL-2 or later.
|
|
*/
|
|
#include <common.h>
|
|
#include <malloc.h>
|
|
#include <part.h>
|
|
#include <mmc.h>
|
|
#include <spi.h>
|
|
#include <crc.h>
|
|
#include <linux/crc7.h>
|
|
#include <linux/byteorder/swab.h>
|
|
|
|
/* MMC/SD in SPI mode reports R1 status always */
|
|
#define R1_SPI_IDLE (1 << 0)
|
|
#define R1_SPI_ERASE_RESET (1 << 1)
|
|
#define R1_SPI_ILLEGAL_COMMAND (1 << 2)
|
|
#define R1_SPI_COM_CRC (1 << 3)
|
|
#define R1_SPI_ERASE_SEQ (1 << 4)
|
|
#define R1_SPI_ADDRESS (1 << 5)
|
|
#define R1_SPI_PARAMETER (1 << 6)
|
|
/* R1 bit 7 is always zero, reuse this bit for error */
|
|
#define R1_SPI_ERROR (1 << 7)
|
|
|
|
/* Response tokens used to ack each block written: */
|
|
#define SPI_MMC_RESPONSE_CODE(x) ((x) & 0x1f)
|
|
#define SPI_RESPONSE_ACCEPTED ((2 << 1)|1)
|
|
#define SPI_RESPONSE_CRC_ERR ((5 << 1)|1)
|
|
#define SPI_RESPONSE_WRITE_ERR ((6 << 1)|1)
|
|
|
|
/* Read and write blocks start with these tokens and end with crc;
|
|
* on error, read tokens act like a subset of R2_SPI_* values.
|
|
*/
|
|
#define SPI_TOKEN_SINGLE 0xfe /* single block r/w, multiblock read */
|
|
#define SPI_TOKEN_MULTI_WRITE 0xfc /* multiblock write */
|
|
#define SPI_TOKEN_STOP_TRAN 0xfd /* terminate multiblock write */
|
|
|
|
/* MMC SPI commands start with a start bit "0" and a transmit bit "1" */
|
|
#define MMC_SPI_CMD(x) (0x40 | (x & 0x3f))
|
|
|
|
/* bus capability */
|
|
#define MMC_SPI_VOLTAGE (MMC_VDD_32_33 | MMC_VDD_33_34)
|
|
#define MMC_SPI_MIN_CLOCK 400000 /* 400KHz to meet MMC spec */
|
|
|
|
/* timeout value */
|
|
#define CTOUT 8
|
|
#define RTOUT 3000000 /* 1 sec */
|
|
#define WTOUT 3000000 /* 1 sec */
|
|
|
|
static uint mmc_spi_sendcmd(struct mmc *mmc, ushort cmdidx, u32 cmdarg)
|
|
{
|
|
struct spi_slave *spi = mmc->priv;
|
|
u8 cmdo[7];
|
|
u8 r1;
|
|
int i;
|
|
cmdo[0] = 0xff;
|
|
cmdo[1] = MMC_SPI_CMD(cmdidx);
|
|
cmdo[2] = cmdarg >> 24;
|
|
cmdo[3] = cmdarg >> 16;
|
|
cmdo[4] = cmdarg >> 8;
|
|
cmdo[5] = cmdarg;
|
|
cmdo[6] = (crc7(0, &cmdo[1], 5) << 1) | 0x01;
|
|
spi_xfer(spi, sizeof(cmdo) * 8, cmdo, NULL, 0);
|
|
for (i = 0; i < CTOUT; i++) {
|
|
spi_xfer(spi, 1 * 8, NULL, &r1, 0);
|
|
if (i && (r1 & 0x80) == 0) /* r1 response */
|
|
break;
|
|
}
|
|
debug("%s:cmd%d resp%d %x\n", __func__, cmdidx, i, r1);
|
|
return r1;
|
|
}
|
|
|
|
static uint mmc_spi_readdata(struct mmc *mmc, void *xbuf,
|
|
u32 bcnt, u32 bsize)
|
|
{
|
|
struct spi_slave *spi = mmc->priv;
|
|
u8 *buf = xbuf;
|
|
u8 r1;
|
|
u16 crc;
|
|
int i;
|
|
while (bcnt--) {
|
|
for (i = 0; i < RTOUT; i++) {
|
|
spi_xfer(spi, 1 * 8, NULL, &r1, 0);
|
|
if (r1 != 0xff) /* data token */
|
|
break;
|
|
}
|
|
debug("%s:tok%d %x\n", __func__, i, r1);
|
|
if (r1 == SPI_TOKEN_SINGLE) {
|
|
spi_xfer(spi, bsize * 8, NULL, buf, 0);
|
|
spi_xfer(spi, 2 * 8, NULL, &crc, 0);
|
|
#ifdef CONFIG_MMC_SPI_CRC_ON
|
|
if (swab16(cyg_crc16(buf, bsize)) != crc) {
|
|
debug("%s: CRC error\n", mmc->name);
|
|
r1 = R1_SPI_COM_CRC;
|
|
break;
|
|
}
|
|
#endif
|
|
r1 = 0;
|
|
} else {
|
|
r1 = R1_SPI_ERROR;
|
|
break;
|
|
}
|
|
buf += bsize;
|
|
}
|
|
return r1;
|
|
}
|
|
|
|
static uint mmc_spi_writedata(struct mmc *mmc, const void *xbuf,
|
|
u32 bcnt, u32 bsize, int multi)
|
|
{
|
|
struct spi_slave *spi = mmc->priv;
|
|
const u8 *buf = xbuf;
|
|
u8 r1;
|
|
u16 crc;
|
|
u8 tok[2];
|
|
int i;
|
|
tok[0] = 0xff;
|
|
tok[1] = multi ? SPI_TOKEN_MULTI_WRITE : SPI_TOKEN_SINGLE;
|
|
while (bcnt--) {
|
|
#ifdef CONFIG_MMC_SPI_CRC_ON
|
|
crc = swab16(cyg_crc16((u8 *)buf, bsize));
|
|
#endif
|
|
spi_xfer(spi, 2 * 8, tok, NULL, 0);
|
|
spi_xfer(spi, bsize * 8, buf, NULL, 0);
|
|
spi_xfer(spi, 2 * 8, &crc, NULL, 0);
|
|
for (i = 0; i < CTOUT; i++) {
|
|
spi_xfer(spi, 1 * 8, NULL, &r1, 0);
|
|
if ((r1 & 0x10) == 0) /* response token */
|
|
break;
|
|
}
|
|
debug("%s:tok%d %x\n", __func__, i, r1);
|
|
if (SPI_MMC_RESPONSE_CODE(r1) == SPI_RESPONSE_ACCEPTED) {
|
|
for (i = 0; i < WTOUT; i++) { /* wait busy */
|
|
spi_xfer(spi, 1 * 8, NULL, &r1, 0);
|
|
if (i && r1 == 0xff) {
|
|
r1 = 0;
|
|
break;
|
|
}
|
|
}
|
|
if (i == WTOUT) {
|
|
debug("%s:wtout %x\n", __func__, r1);
|
|
r1 = R1_SPI_ERROR;
|
|
break;
|
|
}
|
|
} else {
|
|
debug("%s: err %x\n", __func__, r1);
|
|
r1 = R1_SPI_COM_CRC;
|
|
break;
|
|
}
|
|
buf += bsize;
|
|
}
|
|
if (multi && bcnt == -1) { /* stop multi write */
|
|
tok[1] = SPI_TOKEN_STOP_TRAN;
|
|
spi_xfer(spi, 2 * 8, tok, NULL, 0);
|
|
for (i = 0; i < WTOUT; i++) { /* wait busy */
|
|
spi_xfer(spi, 1 * 8, NULL, &r1, 0);
|
|
if (i && r1 == 0xff) {
|
|
r1 = 0;
|
|
break;
|
|
}
|
|
}
|
|
if (i == WTOUT) {
|
|
debug("%s:wstop %x\n", __func__, r1);
|
|
r1 = R1_SPI_ERROR;
|
|
}
|
|
}
|
|
return r1;
|
|
}
|
|
|
|
static int mmc_spi_request(struct mmc *mmc, struct mmc_cmd *cmd,
|
|
struct mmc_data *data)
|
|
{
|
|
struct spi_slave *spi = mmc->priv;
|
|
u8 r1;
|
|
int i;
|
|
int ret = 0;
|
|
debug("%s:cmd%d %x %x %x\n", __func__,
|
|
cmd->cmdidx, cmd->resp_type, cmd->cmdarg, cmd->flags);
|
|
spi_claim_bus(spi);
|
|
spi_cs_activate(spi);
|
|
r1 = mmc_spi_sendcmd(mmc, cmd->cmdidx, cmd->cmdarg);
|
|
if (r1 == 0xff) { /* no response */
|
|
ret = NO_CARD_ERR;
|
|
goto done;
|
|
} else if (r1 & R1_SPI_COM_CRC) {
|
|
ret = COMM_ERR;
|
|
goto done;
|
|
} else if (r1 & ~R1_SPI_IDLE) { /* other errors */
|
|
ret = TIMEOUT;
|
|
goto done;
|
|
} else if (cmd->resp_type == MMC_RSP_R2) {
|
|
r1 = mmc_spi_readdata(mmc, cmd->response, 1, 16);
|
|
for (i = 0; i < 4; i++)
|
|
cmd->response[i] = swab32(cmd->response[i]);
|
|
debug("r128 %x %x %x %x\n", cmd->response[0], cmd->response[1],
|
|
cmd->response[2], cmd->response[3]);
|
|
} else if (!data) {
|
|
switch (cmd->cmdidx) {
|
|
case SD_CMD_APP_SEND_OP_COND:
|
|
case MMC_CMD_SEND_OP_COND:
|
|
cmd->response[0] = (r1 & R1_SPI_IDLE) ? 0 : OCR_BUSY;
|
|
break;
|
|
case SD_CMD_SEND_IF_COND:
|
|
case MMC_CMD_SPI_READ_OCR:
|
|
spi_xfer(spi, 4 * 8, NULL, cmd->response, 0);
|
|
cmd->response[0] = swab32(cmd->response[0]);
|
|
debug("r32 %x\n", cmd->response[0]);
|
|
break;
|
|
}
|
|
} else {
|
|
debug("%s:data %x %x %x\n", __func__,
|
|
data->flags, data->blocks, data->blocksize);
|
|
if (data->flags == MMC_DATA_READ)
|
|
r1 = mmc_spi_readdata(mmc, data->dest,
|
|
data->blocks, data->blocksize);
|
|
else if (data->flags == MMC_DATA_WRITE)
|
|
r1 = mmc_spi_writedata(mmc, data->src,
|
|
data->blocks, data->blocksize,
|
|
(cmd->cmdidx == MMC_CMD_WRITE_MULTIPLE_BLOCK));
|
|
if (r1 & R1_SPI_COM_CRC)
|
|
ret = COMM_ERR;
|
|
else if (r1) /* other errors */
|
|
ret = TIMEOUT;
|
|
}
|
|
done:
|
|
spi_cs_deactivate(spi);
|
|
spi_release_bus(spi);
|
|
return ret;
|
|
}
|
|
|
|
static void mmc_spi_set_ios(struct mmc *mmc)
|
|
{
|
|
struct spi_slave *spi = mmc->priv;
|
|
debug("%s: clock %u\n", __func__, mmc->clock);
|
|
if (mmc->clock)
|
|
spi_set_speed(spi, mmc->clock);
|
|
}
|
|
|
|
static int mmc_spi_init_p(struct mmc *mmc)
|
|
{
|
|
struct spi_slave *spi = mmc->priv;
|
|
mmc->clock = 0;
|
|
spi_set_speed(spi, MMC_SPI_MIN_CLOCK);
|
|
spi_claim_bus(spi);
|
|
/* cs deactivated for 100+ clock */
|
|
spi_xfer(spi, 18 * 8, NULL, NULL, 0);
|
|
spi_release_bus(spi);
|
|
return 0;
|
|
}
|
|
|
|
struct mmc *mmc_spi_init(uint bus, uint cs, uint speed, uint mode)
|
|
{
|
|
struct mmc *mmc;
|
|
|
|
mmc = malloc(sizeof(*mmc));
|
|
if (!mmc)
|
|
return NULL;
|
|
memset(mmc, 0, sizeof(*mmc));
|
|
mmc->priv = spi_setup_slave(bus, cs, speed, mode);
|
|
if (!mmc->priv) {
|
|
free(mmc);
|
|
return NULL;
|
|
}
|
|
sprintf(mmc->name, "MMC_SPI");
|
|
mmc->send_cmd = mmc_spi_request;
|
|
mmc->set_ios = mmc_spi_set_ios;
|
|
mmc->init = mmc_spi_init_p;
|
|
mmc->host_caps = MMC_MODE_SPI;
|
|
|
|
mmc->voltages = MMC_SPI_VOLTAGE;
|
|
mmc->f_max = speed;
|
|
mmc->f_min = MMC_SPI_MIN_CLOCK;
|
|
mmc->block_dev.part_type = PART_TYPE_DOS;
|
|
|
|
mmc_register(mmc);
|
|
|
|
return mmc;
|
|
}
|