b8475e6aca
This converts the following to Kconfig: CONFIG_MACB Signed-off-by: Tom Rini <trini@konsulko.com>
101 lines
2.8 KiB
C
101 lines
2.8 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Bluewater Systems Snapper 9260 and 9G20 modules
|
|
*
|
|
* (C) Copyright 2011 Bluewater Systems
|
|
* Author: Andre Renaud <andre@bluewatersys.com>
|
|
* Author: Ryan Mallon <ryan@bluewatersys.com>
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/* SoC type is defined in boards.cfg */
|
|
#include <asm/hardware.h>
|
|
#include <linux/sizes.h>
|
|
|
|
/* ARM asynchronous clock */
|
|
#define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* External Crystal, in Hz */
|
|
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
|
|
|
|
/* CPU */
|
|
|
|
/* SDRAM */
|
|
#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS1
|
|
#define CONFIG_SYS_SDRAM_SIZE (64 * 1024 * 1024) /* 64MB */
|
|
#define CONFIG_SYS_INIT_SP_ADDR (ATMEL_BASE_SRAM1 + 0x1000 - \
|
|
GENERATED_GBL_DATA_SIZE)
|
|
|
|
/* Mem test settings */
|
|
|
|
/* NAND Flash */
|
|
#define CONFIG_SYS_MAX_NAND_DEVICE 1
|
|
#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3
|
|
#define CONFIG_SYS_NAND_DBW_8
|
|
#define CONFIG_SYS_NAND_MASK_ALE (1 << 21) /* AD21 */
|
|
#define CONFIG_SYS_NAND_MASK_CLE (1 << 22) /* AD22 */
|
|
#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14
|
|
#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC13
|
|
|
|
/* Ethernet */
|
|
#define CONFIG_RMII
|
|
#define CONFIG_NET_RETRY_COUNT 20
|
|
#define CONFIG_RESET_PHY_R
|
|
#define CONFIG_AT91_WANTS_COMMON_PHY
|
|
#define CONFIG_TFTP_PORT
|
|
|
|
/* USB */
|
|
#define CONFIG_USB_ATMEL
|
|
#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
|
|
#define CONFIG_USB_OHCI_NEW
|
|
#define CONFIG_SYS_USB_OHCI_CPU_INIT
|
|
#define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_UHP_BASE
|
|
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9260"
|
|
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
|
|
|
|
/* GPIOs and IO expander */
|
|
#define CONFIG_ATMEL_LEGACY
|
|
#define CONFIG_AT91_GPIO_PULLUP 1
|
|
#define CONFIG_PCA953X
|
|
#define CONFIG_SYS_I2C_PCA953X_ADDR 0x28
|
|
#define CONFIG_SYS_I2C_PCA953X_WIDTH { {0x28, 16} }
|
|
|
|
/* UARTs/Serial console */
|
|
#ifndef CONFIG_DM_SERIAL
|
|
#define CONFIG_USART_BASE ATMEL_BASE_DBGU
|
|
#define CONFIG_USART_ID ATMEL_ID_SYS
|
|
#endif
|
|
|
|
/* I2C - Bit-bashed */
|
|
#define CONFIG_SOFT_I2C_READ_REPEATED_START
|
|
#define I2C_INIT do { \
|
|
at91_set_gpio_output(AT91_PIN_PA23, 1); \
|
|
at91_set_gpio_output(AT91_PIN_PA24, 1); \
|
|
at91_set_pio_multi_drive(AT91_PIO_PORTA, 23, 1); \
|
|
at91_set_pio_multi_drive(AT91_PIO_PORTA, 24, 1); \
|
|
} while (0)
|
|
#define I2C_SOFT_DECLARATIONS
|
|
#define I2C_ACTIVE
|
|
#define I2C_TRISTATE at91_set_gpio_input(AT91_PIN_PA23, 1);
|
|
#define I2C_READ at91_get_gpio_value(AT91_PIN_PA23);
|
|
#define I2C_SDA(bit) do { \
|
|
if (bit) { \
|
|
at91_set_gpio_input(AT91_PIN_PA23, 1); \
|
|
} else { \
|
|
at91_set_gpio_output(AT91_PIN_PA23, 1); \
|
|
at91_set_gpio_value(AT91_PIN_PA23, bit); \
|
|
} \
|
|
} while (0)
|
|
#define I2C_SCL(bit) at91_set_pio_value(AT91_PIO_PORTA, 24, bit)
|
|
#define I2C_DELAY udelay(2)
|
|
|
|
/* Boot options */
|
|
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
|
|
/* Environment settings */
|
|
|
|
/* Console settings */
|
|
|
|
#endif /* __CONFIG_H */
|