c9ffd839b1
* Check DDR interleaving mode from environment by reading memctl_intlv_ctl and ba_intlv_ctl. * Print DDR interleaving mode information * Add doc/README.fsl-ddr to describe the interleaving setting Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
70 lines
3.2 KiB
Plaintext
70 lines
3.2 KiB
Plaintext
|
|
Table of interleaving modes supported in cpu/8xxx/ddr/
|
|
======================================================
|
|
+-------------+---------------------------------------------------------+
|
|
| | Rank Interleaving |
|
|
| +--------+-----------+-----------+------------+-----------+
|
|
|Memory | | | | 2x2 | 4x1 |
|
|
|Controller | None | 2x1 lower | 2x1 upper | {CS0+CS1}, | {CS0+CS1+ |
|
|
|Interleaving | | {CS0+CS1} | {CS2+CS3} | {CS2+CS3} | CS2+CS3} |
|
|
+-------------+--------+-----------+-----------+------------+-----------+
|
|
|None | Yes | Yes | Yes | Yes | Yes |
|
|
+-------------+--------+-----------+-----------+------------+-----------+
|
|
|Cacheline | Yes | Yes | No | No, Only(*)| Yes |
|
|
| |CS0 Only| | | {CS0+CS1} | |
|
|
+-------------+--------+-----------+-----------+------------+-----------+
|
|
|Page | Yes | Yes | No | No, Only(*)| Yes |
|
|
| |CS0 Only| | | {CS0+CS1} | |
|
|
+-------------+--------+-----------+-----------+------------+-----------+
|
|
|Bank | Yes | Yes | No | No, Only(*)| Yes |
|
|
| |CS0 Only| | | {CS0+CS1} | |
|
|
+-------------+--------+-----------+-----------+------------+-----------+
|
|
|Superbank | No | Yes | No | No, Only(*)| Yes |
|
|
| | | | | {CS0+CS1} | |
|
|
+-------------+--------+-----------+-----------+------------+-----------+
|
|
(*) Although the hardware can be configured with memory controller
|
|
interleaving using "2x2" rank interleaving, it only interleaves {CS0+CS1}
|
|
from each controller. {CS2+CS3} on each controller are only rank
|
|
interleaved on that controller.
|
|
|
|
The ways to configure the ddr interleaving mode
|
|
==============================================
|
|
1. In board header file(e.g.MPC8572DS.h), add default interleaving setting
|
|
under "CONFIG_EXTRA_ENV_SETTINGS", like:
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"memctl_intlv_ctl=2\0" \
|
|
......
|
|
|
|
2. Run u-boot "setenv" command to configure the memory interleaving mode.
|
|
Either numerical or string value is accepted.
|
|
|
|
# disable memory controller interleaving
|
|
setenv memctl_intlv_ctl
|
|
|
|
# cacheline interleaving
|
|
setenv memctl_intlv_ctl 0 or setenv memctl_intlv_ctl cacheline
|
|
|
|
# page interleaving
|
|
setenv memctl_intlv_ctl 1 or setenv memctl_intlv_ctl page
|
|
|
|
# bank interleaving
|
|
setenv memctl_intlv_ctl 2 or setenv memctl_intlv_ctl bank
|
|
|
|
# superbank
|
|
setenv memctl_intlv_ctl 3 or setenv memctl_intlv_ctl superbank
|
|
|
|
# disable bank (chip-select) interleaving
|
|
setenv ba_intlv_ctl
|
|
|
|
# bank(chip-select) interleaving cs0+cs1
|
|
setenv ba_intlv_ctl 0x40 or setenv ba_intlv_ctl cs0_cs1
|
|
|
|
# bank(chip-select) interleaving cs2+cs3
|
|
setenv ba_intlv_ctl 0x20 or setenv ba_intlv_ctl cs2_cs3
|
|
|
|
# bank(chip-select) interleaving (cs0+cs1) and (cs2+cs3) (2x2)
|
|
setenv ba_intlv_ctl 0x60 or setenv ba_intlv_ctl cs0_cs1_and_cs2_cs3
|
|
|
|
# bank(chip-select) interleaving (cs0+cs1+cs2+cs3) (4x1)
|
|
setenv ba_intlv_ctl 0x04 or setenv ba_intlv_ctl cs0_cs1_cs2_cs3
|