c7190f028f
some LCRR bits are not documented throughout the 83xx family RMs. New board porters copying similar board configurations might omit setting e.g., DBYP since it was not documented in their SoC's RM. Prevent them bricking their board by retaining power on reset values in bit fields that the board porter doesn't explicitly configure via CONFIG_SYS_<registername>_<bitfield> assignments in the board config file. also move LCRR assignment to cpu_init_r[am] to help ensure no transactions are being executed via the local bus while CLKDIV is being modified. also start to use i/o accessors. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
645 lines
20 KiB
C
645 lines
20 KiB
C
/*
|
|
* Copyright (C) Freescale Semiconductor, Inc. 2006.
|
|
*
|
|
* See file CREDITS for list of people who contributed to this
|
|
* project.
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License as
|
|
* published by the Free Software Foundation; either version 2 of
|
|
* the License, or (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
|
|
* MA 02111-1307 USA
|
|
*/
|
|
/*
|
|
* mpc8313epb board configuration file
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
*/
|
|
#define CONFIG_E300 1
|
|
#define CONFIG_MPC83xx 1
|
|
#define CONFIG_MPC831x 1
|
|
#define CONFIG_MPC8313 1
|
|
#define CONFIG_MPC8313ERDB 1
|
|
|
|
#define CONFIG_PCI
|
|
|
|
#define CONFIG_MISC_INIT_R
|
|
|
|
/*
|
|
* On-board devices
|
|
*
|
|
* TSEC1 is VSC switch
|
|
* TSEC2 is SoC TSEC
|
|
*/
|
|
#define CONFIG_VSC7385_ENET
|
|
#define CONFIG_TSEC2
|
|
|
|
#ifdef CONFIG_SYS_66MHZ
|
|
#define CONFIG_83XX_CLKIN 66666667 /* in Hz */
|
|
#elif defined(CONFIG_SYS_33MHZ)
|
|
#define CONFIG_83XX_CLKIN 33333333 /* in Hz */
|
|
#else
|
|
#error Unknown oscillator frequency.
|
|
#endif
|
|
|
|
#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
|
|
|
|
#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
|
|
|
|
#define CONFIG_SYS_IMMR 0xE0000000
|
|
|
|
#if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
|
|
#define CONFIG_DEFAULT_IMMR CONFIG_SYS_IMMR
|
|
#endif
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x00001000
|
|
#define CONFIG_SYS_MEMTEST_END 0x07f00000
|
|
|
|
/* Early revs of this board will lock up hard when attempting
|
|
* to access the PMC registers, unless a JTAG debugger is
|
|
* connected, or some resistor modifications are made.
|
|
*/
|
|
#define CONFIG_SYS_8313ERDB_BROKEN_PMC 1
|
|
|
|
#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
|
|
#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
|
|
|
|
/*
|
|
* Device configurations
|
|
*/
|
|
|
|
/* Vitesse 7385 */
|
|
|
|
#ifdef CONFIG_VSC7385_ENET
|
|
|
|
#define CONFIG_TSEC1
|
|
|
|
/* The flash address and size of the VSC7385 firmware image */
|
|
#define CONFIG_VSC7385_IMAGE 0xFE7FE000
|
|
#define CONFIG_VSC7385_IMAGE_SIZE 8192
|
|
|
|
#endif
|
|
|
|
/*
|
|
* DDR Setup
|
|
*/
|
|
#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/
|
|
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
|
|
#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
|
|
|
|
/*
|
|
* Manually set up DDR parameters, as this board does not
|
|
* seem to have the SPD connected to I2C.
|
|
*/
|
|
#define CONFIG_SYS_DDR_SIZE 128 /* MB */
|
|
#define CONFIG_SYS_DDR_CONFIG ( CSCONFIG_EN \
|
|
| 0x00010000 /* TODO */ \
|
|
| CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10 )
|
|
/* 0x80010102 */
|
|
|
|
#define CONFIG_SYS_DDR_TIMING_3 0x00000000
|
|
#define CONFIG_SYS_DDR_TIMING_0 ( ( 0 << TIMING_CFG0_RWT_SHIFT ) \
|
|
| ( 0 << TIMING_CFG0_WRT_SHIFT ) \
|
|
| ( 0 << TIMING_CFG0_RRT_SHIFT ) \
|
|
| ( 0 << TIMING_CFG0_WWT_SHIFT ) \
|
|
| ( 2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT ) \
|
|
| ( 2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT ) \
|
|
| ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \
|
|
| ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) )
|
|
/* 0x00220802 */
|
|
#define CONFIG_SYS_DDR_TIMING_1 ( ( 3 << TIMING_CFG1_PRETOACT_SHIFT ) \
|
|
| ( 8 << TIMING_CFG1_ACTTOPRE_SHIFT ) \
|
|
| ( 3 << TIMING_CFG1_ACTTORW_SHIFT ) \
|
|
| ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \
|
|
| (10 << TIMING_CFG1_REFREC_SHIFT ) \
|
|
| ( 3 << TIMING_CFG1_WRREC_SHIFT ) \
|
|
| ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \
|
|
| ( 2 << TIMING_CFG1_WRTORD_SHIFT ) )
|
|
/* 0x3835a322 */
|
|
#define CONFIG_SYS_DDR_TIMING_2 ( ( 1 << TIMING_CFG2_ADD_LAT_SHIFT ) \
|
|
| ( 5 << TIMING_CFG2_CPO_SHIFT ) \
|
|
| ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \
|
|
| ( 2 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \
|
|
| ( 2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT ) \
|
|
| ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \
|
|
| ( 6 << TIMING_CFG2_FOUR_ACT_SHIFT) )
|
|
/* 0x129048c6 */ /* P9-45,may need tuning */
|
|
#define CONFIG_SYS_DDR_INTERVAL ( ( 1296 << SDRAM_INTERVAL_REFINT_SHIFT ) \
|
|
| ( 1280 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) )
|
|
/* 0x05100500 */
|
|
#if defined(CONFIG_DDR_2T_TIMING)
|
|
#define CONFIG_SYS_SDRAM_CFG ( SDRAM_CFG_SREN \
|
|
| SDRAM_CFG_SDRAM_TYPE_DDR2 \
|
|
| SDRAM_CFG_2T_EN \
|
|
| SDRAM_CFG_DBW_32 )
|
|
#else
|
|
#define CONFIG_SYS_SDRAM_CFG ( SDRAM_CFG_SREN \
|
|
| SDRAM_CFG_SDRAM_TYPE_DDR2 \
|
|
| SDRAM_CFG_32_BE )
|
|
/* 0x43080000 */
|
|
#endif
|
|
#define CONFIG_SYS_SDRAM_CFG2 0x00401000
|
|
/* set burst length to 8 for 32-bit data path */
|
|
#define CONFIG_SYS_DDR_MODE ( ( 0x4448 << SDRAM_MODE_ESD_SHIFT ) \
|
|
| ( 0x0632 << SDRAM_MODE_SD_SHIFT ) )
|
|
/* 0x44480632 */
|
|
#define CONFIG_SYS_DDR_MODE_2 0x8000C000
|
|
|
|
#define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
|
|
/*0x02000000*/
|
|
#define CONFIG_SYS_DDRCDR_VALUE ( DDRCDR_EN \
|
|
| DDRCDR_PZ_NOMZ \
|
|
| DDRCDR_NZ_NOMZ \
|
|
| DDRCDR_M_ODR )
|
|
|
|
/*
|
|
* FLASH on the Local Bus
|
|
*/
|
|
#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
|
|
#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
|
|
#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* start of FLASH */
|
|
#define CONFIG_SYS_FLASH_SIZE 8 /* flash size in MB */
|
|
#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */
|
|
#define CONFIG_SYS_FLASH_EMPTY_INFO /* display empty sectors */
|
|
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* buffer up multiple bytes */
|
|
|
|
#define CONFIG_SYS_NOR_BR_PRELIM (CONFIG_SYS_FLASH_BASE | /* flash Base address */ \
|
|
(2 << BR_PS_SHIFT) | /* 16 bit port size */ \
|
|
BR_V) /* valid */
|
|
#define CONFIG_SYS_NOR_OR_PRELIM ( 0xFF800000 /* 8 MByte */ \
|
|
| OR_GPCM_XACS \
|
|
| OR_GPCM_SCY_9 \
|
|
| OR_GPCM_EHTR \
|
|
| OR_GPCM_EAD )
|
|
/* 0xFF006FF7 TODO SLOW 16 MB flash size */
|
|
#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE /* window base at flash base */
|
|
#define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000017 /* 16 MB window size */
|
|
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 135 /* sectors per device */
|
|
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
|
|
|
|
#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
|
|
|
|
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) && !defined(CONFIG_NAND_SPL)
|
|
#define CONFIG_SYS_RAMBOOT
|
|
#endif
|
|
|
|
#define CONFIG_SYS_INIT_RAM_LOCK 1
|
|
#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */
|
|
#define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM*/
|
|
|
|
#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
|
|
#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
|
|
#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
|
|
|
|
/*
|
|
* Local Bus LCRR and LBCR regs
|
|
*/
|
|
#define CONFIG_SYS_LCRR_EADC LCRR_EADC_1
|
|
#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
|
|
#define CONFIG_SYS_LBC_LBCR ( 0x00040000 /* TODO */ \
|
|
| (0xFF << LBCR_BMT_SHIFT) \
|
|
| 0xF ) /* 0x0004ff0f */
|
|
|
|
#define CONFIG_SYS_LBC_MRTPR 0x20000000 /*TODO */ /* LB refresh timer prescal, 266MHz/32 */
|
|
|
|
/* drivers/mtd/nand/nand.c */
|
|
#ifdef CONFIG_NAND_SPL
|
|
#define CONFIG_SYS_NAND_BASE 0xFFF00000
|
|
#else
|
|
#define CONFIG_SYS_NAND_BASE 0xE2800000
|
|
#endif
|
|
|
|
#define CONFIG_SYS_MAX_NAND_DEVICE 1
|
|
#define CONFIG_MTD_NAND_VERIFY_WRITE
|
|
#define CONFIG_CMD_NAND 1
|
|
#define CONFIG_NAND_FSL_ELBC 1
|
|
#define CONFIG_SYS_NAND_BLOCK_SIZE 16384
|
|
#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */
|
|
|
|
#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10)
|
|
#define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000
|
|
#define CONFIG_SYS_NAND_U_BOOT_START 0x00100100
|
|
#define CONFIG_SYS_NAND_U_BOOT_OFFS 16384
|
|
#define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000
|
|
#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_RELOC + 0x10000)
|
|
|
|
#define CONFIG_SYS_NAND_BR_PRELIM ( CONFIG_SYS_NAND_BASE \
|
|
| (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
|
|
| BR_PS_8 /* Port Size = 8 bit */ \
|
|
| BR_MS_FCM /* MSEL = FCM */ \
|
|
| BR_V ) /* valid */
|
|
#define CONFIG_SYS_NAND_OR_PRELIM ( 0xFFFF8000 /* length 32K */ \
|
|
| OR_FCM_CSCT \
|
|
| OR_FCM_CST \
|
|
| OR_FCM_CHT \
|
|
| OR_FCM_SCY_1 \
|
|
| OR_FCM_TRLX \
|
|
| OR_FCM_EHTR )
|
|
/* 0xFFFF8396 */
|
|
|
|
#ifdef CONFIG_NAND_U_BOOT
|
|
#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM
|
|
#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM
|
|
#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NOR_BR_PRELIM
|
|
#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NOR_OR_PRELIM
|
|
#else
|
|
#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NOR_BR_PRELIM
|
|
#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NOR_OR_PRELIM
|
|
#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM
|
|
#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM
|
|
#endif
|
|
|
|
#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE
|
|
#define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000E /* 32KB */
|
|
|
|
#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM
|
|
#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM
|
|
|
|
/* local bus read write buffer mapping */
|
|
#define CONFIG_SYS_BR3_PRELIM 0xFA000801 /* map at 0xFA000000 */
|
|
#define CONFIG_SYS_OR3_PRELIM 0xFFFF8FF7 /* 32kB */
|
|
#define CONFIG_SYS_LBLAWBAR3_PRELIM 0xFA000000
|
|
#define CONFIG_SYS_LBLAWAR3_PRELIM 0x8000000E /* 32KB */
|
|
|
|
/* Vitesse 7385 */
|
|
|
|
#define CONFIG_SYS_VSC7385_BASE 0xF0000000
|
|
|
|
#ifdef CONFIG_VSC7385_ENET
|
|
|
|
#define CONFIG_SYS_BR2_PRELIM 0xf0000801 /* VSC7385 Base address */
|
|
#define CONFIG_SYS_OR2_PRELIM 0xfffe09ff /* VSC7385, 128K bytes*/
|
|
#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_VSC7385_BASE/* Access window base at VSC7385 base */
|
|
#define CONFIG_SYS_LBLAWAR2_PRELIM 0x80000010 /* Access window size 128K */
|
|
|
|
#endif
|
|
|
|
/* pass open firmware flat tree */
|
|
#define CONFIG_OF_LIBFDT 1
|
|
#define CONFIG_OF_BOARD_SETUP 1
|
|
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
|
|
|
|
/*
|
|
* Serial Port
|
|
*/
|
|
#define CONFIG_CONS_INDEX 1
|
|
#define CONFIG_SYS_NS16550
|
|
#define CONFIG_SYS_NS16550_SERIAL
|
|
#define CONFIG_SYS_NS16550_REG_SIZE 1
|
|
|
|
#define CONFIG_SYS_BAUDRATE_TABLE \
|
|
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
|
|
|
|
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
|
|
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
|
|
|
|
/* Use the HUSH parser */
|
|
#define CONFIG_SYS_HUSH_PARSER
|
|
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
|
|
|
|
/* I2C */
|
|
#define CONFIG_HARD_I2C /* I2C with hardware support*/
|
|
#define CONFIG_FSL_I2C
|
|
#define CONFIG_I2C_MULTI_BUS
|
|
#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
|
|
#define CONFIG_SYS_I2C_SLAVE 0x7F
|
|
#define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */
|
|
#define CONFIG_SYS_I2C_OFFSET 0x3000
|
|
#define CONFIG_SYS_I2C2_OFFSET 0x3100
|
|
|
|
/*
|
|
* General PCI
|
|
* Addresses are mapped 1-1.
|
|
*/
|
|
#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
|
|
#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
|
|
#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
|
|
#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
|
|
#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
|
|
#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
|
|
#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
|
|
#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
|
|
#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */
|
|
|
|
#define CONFIG_PCI_PNP /* do pci plug-and-play */
|
|
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
|
|
|
|
/*
|
|
* TSEC
|
|
*/
|
|
#define CONFIG_TSEC_ENET /* TSEC ethernet support */
|
|
|
|
#define CONFIG_NET_MULTI
|
|
#define CONFIG_GMII /* MII PHY management */
|
|
|
|
#ifdef CONFIG_TSEC1
|
|
#define CONFIG_HAS_ETH0
|
|
#define CONFIG_TSEC1_NAME "TSEC0"
|
|
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
|
|
#define TSEC1_PHY_ADDR 0x1c
|
|
#define TSEC1_FLAGS TSEC_GIGABIT
|
|
#define TSEC1_PHYIDX 0
|
|
#endif
|
|
|
|
#ifdef CONFIG_TSEC2
|
|
#define CONFIG_HAS_ETH1
|
|
#define CONFIG_TSEC2_NAME "TSEC1"
|
|
#define CONFIG_SYS_TSEC2_OFFSET 0x25000
|
|
#define TSEC2_PHY_ADDR 4
|
|
#define TSEC2_FLAGS TSEC_GIGABIT
|
|
#define TSEC2_PHYIDX 0
|
|
#endif
|
|
|
|
|
|
/* Options are: TSEC[0-1] */
|
|
#define CONFIG_ETHPRIME "TSEC1"
|
|
|
|
/*
|
|
* Configure on-board RTC
|
|
*/
|
|
#define CONFIG_RTC_DS1337
|
|
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
|
|
|
|
/*
|
|
* Environment
|
|
*/
|
|
#if defined(CONFIG_NAND_U_BOOT)
|
|
#define CONFIG_ENV_IS_IN_NAND 1
|
|
#define CONFIG_ENV_OFFSET (512 * 1024)
|
|
#define CONFIG_ENV_SECT_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
|
|
#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
|
|
#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
|
|
#define CONFIG_ENV_RANGE (CONFIG_ENV_SECT_SIZE * 4)
|
|
#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE)
|
|
#elif !defined(CONFIG_SYS_RAMBOOT)
|
|
#define CONFIG_ENV_IS_IN_FLASH 1
|
|
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
|
|
#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */
|
|
#define CONFIG_ENV_SIZE 0x2000
|
|
|
|
/* Address and size of Redundant Environment Sector */
|
|
#else
|
|
#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
|
|
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
|
|
#define CONFIG_ENV_SIZE 0x2000
|
|
#endif
|
|
|
|
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
|
|
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
#define CONFIG_BOOTP_BOOTPATH
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
#define CONFIG_BOOTP_HOSTNAME
|
|
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
#include <config_cmd_default.h>
|
|
|
|
#define CONFIG_CMD_PING
|
|
#define CONFIG_CMD_DHCP
|
|
#define CONFIG_CMD_I2C
|
|
#define CONFIG_CMD_MII
|
|
#define CONFIG_CMD_DATE
|
|
#define CONFIG_CMD_PCI
|
|
|
|
#if defined(CONFIG_SYS_RAMBOOT) && !defined(CONFIG_NAND_U_BOOT)
|
|
#undef CONFIG_CMD_SAVEENV
|
|
#undef CONFIG_CMD_LOADS
|
|
#endif
|
|
|
|
#define CONFIG_CMDLINE_EDITING 1
|
|
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
|
|
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
|
|
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
|
|
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
|
|
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
|
|
|
|
#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */
|
|
|
|
#ifdef CONFIG_SYS_66MHZ
|
|
|
|
/* 66MHz IN, 133MHz CSB, 266 DDR, 266 CORE */
|
|
/* 0x62040000 */
|
|
#define CONFIG_SYS_HRCW_LOW (\
|
|
0x20000000 /* reserved, must be set */ |\
|
|
HRCWL_DDRCM |\
|
|
HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
|
|
HRCWL_DDR_TO_SCB_CLK_2X1 |\
|
|
HRCWL_CSB_TO_CLKIN_2X1 |\
|
|
HRCWL_CORE_TO_CSB_2X1)
|
|
|
|
#define CONFIG_SYS_NS16550_CLK (CONFIG_83XX_CLKIN * 2)
|
|
|
|
#elif defined(CONFIG_SYS_33MHZ)
|
|
|
|
/* 33MHz IN, 165MHz CSB, 330 DDR, 330 CORE */
|
|
/* 0x65040000 */
|
|
#define CONFIG_SYS_HRCW_LOW (\
|
|
0x20000000 /* reserved, must be set */ |\
|
|
HRCWL_DDRCM |\
|
|
HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
|
|
HRCWL_DDR_TO_SCB_CLK_2X1 |\
|
|
HRCWL_CSB_TO_CLKIN_5X1 |\
|
|
HRCWL_CORE_TO_CSB_2X1)
|
|
|
|
#define CONFIG_SYS_NS16550_CLK (CONFIG_83XX_CLKIN * 5)
|
|
|
|
#endif
|
|
|
|
#define CONFIG_SYS_HRCW_HIGH_BASE (\
|
|
HRCWH_PCI_HOST |\
|
|
HRCWH_PCI1_ARBITER_ENABLE |\
|
|
HRCWH_CORE_ENABLE |\
|
|
HRCWH_BOOTSEQ_DISABLE |\
|
|
HRCWH_SW_WATCHDOG_DISABLE |\
|
|
HRCWH_TSEC1M_IN_RGMII |\
|
|
HRCWH_TSEC2M_IN_RGMII |\
|
|
HRCWH_BIG_ENDIAN)
|
|
|
|
#ifdef CONFIG_NAND_SPL
|
|
#define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\
|
|
HRCWH_FROM_0XFFF00100 |\
|
|
HRCWH_ROM_LOC_NAND_SP_8BIT |\
|
|
HRCWH_RL_EXT_NAND)
|
|
#else
|
|
#define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\
|
|
HRCWH_FROM_0X00000100 |\
|
|
HRCWH_ROM_LOC_LOCAL_16BIT |\
|
|
HRCWH_RL_EXT_LEGACY)
|
|
#endif
|
|
|
|
/* System IO Config */
|
|
#define CONFIG_SYS_SICRH (SICRH_TSOBI1 | SICRH_TSOBI2) /* RGMII */
|
|
#define CONFIG_SYS_SICRL SICRL_USBDR /* Enable Internal USB Phy */
|
|
|
|
#define CONFIG_SYS_HID0_INIT 0x000000000
|
|
#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
|
|
HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
|
|
|
|
#define CONFIG_SYS_HID2 HID2_HBE
|
|
|
|
#define CONFIG_HIGH_BATS 1 /* High BATs supported */
|
|
|
|
/* DDR @ 0x00000000 */
|
|
#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10)
|
|
#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
|
|
|
|
/* PCI @ 0x80000000 */
|
|
#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_10)
|
|
#define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
|
|
#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
|
|
#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
|
|
|
|
/* PCI2 not supported on 8313 */
|
|
#define CONFIG_SYS_IBAT3L (0)
|
|
#define CONFIG_SYS_IBAT3U (0)
|
|
#define CONFIG_SYS_IBAT4L (0)
|
|
#define CONFIG_SYS_IBAT4U (0)
|
|
|
|
/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
|
|
#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
|
|
#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR | BATU_BL_256M | BATU_VS | BATU_VP)
|
|
|
|
/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
|
|
#define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_10 | BATL_GUARDEDSTORAGE)
|
|
#define CONFIG_SYS_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
|
|
|
|
#define CONFIG_SYS_IBAT7L (0)
|
|
#define CONFIG_SYS_IBAT7U (0)
|
|
|
|
#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
|
|
#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
|
|
#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
|
|
#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
|
|
#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
|
|
#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
|
|
#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
|
|
#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
|
|
#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
|
|
#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
|
|
#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
|
|
#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
|
|
#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
|
|
#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
|
|
#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
|
|
#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
|
|
|
|
/*
|
|
* Internal Definitions
|
|
*
|
|
* Boot Flags
|
|
*/
|
|
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
|
|
#define BOOTFLAG_WARM 0x02 /* Software reboot */
|
|
|
|
/*
|
|
* Environment Configuration
|
|
*/
|
|
#define CONFIG_ENV_OVERWRITE
|
|
|
|
#define CONFIG_ETHADDR 00:E0:0C:00:95:01
|
|
#define CONFIG_ETH1ADDR 00:E0:0C:00:95:02
|
|
|
|
#define CONFIG_IPADDR 10.0.0.2
|
|
#define CONFIG_SERVERIP 10.0.0.1
|
|
#define CONFIG_GATEWAYIP 10.0.0.1
|
|
#define CONFIG_NETMASK 255.0.0.0
|
|
#define CONFIG_NETDEV eth1
|
|
|
|
#define CONFIG_HOSTNAME mpc8313erdb
|
|
#define CONFIG_ROOTPATH /nfs/root/path
|
|
#define CONFIG_BOOTFILE uImage
|
|
#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
|
|
#define CONFIG_FDTFILE mpc8313erdb.dtb
|
|
|
|
#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
|
|
#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
|
|
#define CONFIG_BAUDRATE 115200
|
|
|
|
#define XMK_STR(x) #x
|
|
#define MK_STR(x) XMK_STR(x)
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"netdev=" MK_STR(CONFIG_NETDEV) "\0" \
|
|
"ethprime=TSEC1\0" \
|
|
"uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
|
|
"tftpflash=tftpboot $loadaddr $uboot; " \
|
|
"protect off " MK_STR(TEXT_BASE) " +$filesize; " \
|
|
"erase " MK_STR(TEXT_BASE) " +$filesize; " \
|
|
"cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
|
|
"protect on " MK_STR(TEXT_BASE) " +$filesize; " \
|
|
"cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
|
|
"fdtaddr=780000\0" \
|
|
"fdtfile=" MK_STR(CONFIG_FDTFILE) "\0" \
|
|
"console=ttyS0\0" \
|
|
"setbootargs=setenv bootargs " \
|
|
"root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
|
|
"setipargs=setenv bootargs nfsroot=$serverip:$rootpath " \
|
|
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
|
|
"root=$rootdev rw console=$console,$baudrate $othbootargs\0"
|
|
|
|
#define CONFIG_NFSBOOTCOMMAND \
|
|
"setenv rootdev /dev/nfs;" \
|
|
"run setbootargs;" \
|
|
"run setipargs;" \
|
|
"tftp $loadaddr $bootfile;" \
|
|
"tftp $fdtaddr $fdtfile;" \
|
|
"bootm $loadaddr - $fdtaddr"
|
|
|
|
#define CONFIG_RAMBOOTCOMMAND \
|
|
"setenv rootdev /dev/ram;" \
|
|
"run setbootargs;" \
|
|
"tftp $ramdiskaddr $ramdiskfile;" \
|
|
"tftp $loadaddr $bootfile;" \
|
|
"tftp $fdtaddr $fdtfile;" \
|
|
"bootm $loadaddr $ramdiskaddr $fdtaddr"
|
|
|
|
#undef MK_STR
|
|
#undef XMK_STR
|
|
|
|
#endif /* __CONFIG_H */
|