bf904ea418
The "autoload" environment variable is always checked with env_get_yesno as it can be set to any form of no. The default behavior of env_get_yesno is to return -1 on variables that are not set, which acts as true in general (we test for non-zero return). To convert CONFIG_SYS_AUTOLOAD to Kconfig, given that it was almost always used to set autoload to no, first rename to CONFIG_SYS_DISABLE_AUTOLOAD for consistency sake. Then, make it so that if enabled we set autoload=0 in the default environment. Migrate all platforms which set CONFIG_SYS_AUTOLOAD to non-true or that set autoload to false in their default environment to using CONFIG_SYS_DISABLE_AUTOLOAD Signed-off-by: Tom Rini <trini@konsulko.com>
92 lines
2.5 KiB
Plaintext
92 lines
2.5 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_ARCH_STM32MP=y
|
|
CONFIG_SYS_MALLOC_F_LEN=0x3000
|
|
CONFIG_ENV_OFFSET=0x280000
|
|
CONFIG_DEFAULT_DEVICE_TREE="stm32mp157a-microgea-stm32mp1-microdev2.0"
|
|
CONFIG_SPL_TEXT_BASE=0x2FFC2500
|
|
CONFIG_SPL_MMC=y
|
|
CONFIG_SPL=y
|
|
CONFIG_TARGET_MICROGEA_STM32MP1=y
|
|
CONFIG_ENV_OFFSET_REDUND=0x2C0000
|
|
# CONFIG_ARMV7_VIRT is not set
|
|
CONFIG_SYS_LOAD_ADDR=0xc2000000
|
|
CONFIG_SYS_MEMTEST_START=0xc0000000
|
|
CONFIG_SYS_MEMTEST_END=0xc4000000
|
|
CONFIG_DISTRO_DEFAULTS=y
|
|
CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
|
|
CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc0100000
|
|
CONFIG_FIT=y
|
|
CONFIG_BOOTCOMMAND="run bootcmd_stm32mp"
|
|
CONFIG_SPL_FOOTPRINT_LIMIT=y
|
|
CONFIG_SPL_MAX_FOOTPRINT=0x3db00
|
|
# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
|
|
CONFIG_SPL_STACK=0x30000000
|
|
CONFIG_SYS_SPL_MALLOC=y
|
|
CONFIG_HAS_CUSTOM_SPL_MALLOC_START=y
|
|
CONFIG_CUSTOM_SYS_SPL_MALLOC_ADDR=0xc0300000
|
|
CONFIG_SYS_SPL_MALLOC_SIZE=0x1d00000
|
|
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
|
|
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION=3
|
|
CONFIG_SPL_ENV_SUPPORT=y
|
|
CONFIG_SPL_I2C=y
|
|
CONFIG_SPL_POWER=y
|
|
CONFIG_SYS_PROMPT="STM32MP> "
|
|
CONFIG_SYS_PBSIZE=1050
|
|
CONFIG_CMD_ADTIMG=y
|
|
CONFIG_CMD_ERASEENV=y
|
|
CONFIG_CMD_MEMINFO=y
|
|
CONFIG_CMD_MEMTEST=y
|
|
CONFIG_CMD_ADC=y
|
|
CONFIG_CMD_CLK=y
|
|
CONFIG_CMD_FUSE=y
|
|
CONFIG_CMD_GPIO=y
|
|
CONFIG_CMD_I2C=y
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_REMOTEPROC=y
|
|
CONFIG_SYS_DISABLE_AUTOLOAD=y
|
|
CONFIG_CMD_CACHE=y
|
|
CONFIG_CMD_TIME=y
|
|
CONFIG_CMD_TIMER=y
|
|
CONFIG_CMD_PMIC=y
|
|
CONFIG_CMD_REGULATOR=y
|
|
CONFIG_CMD_EXT4_WRITE=y
|
|
# CONFIG_SPL_DOS_PARTITION is not set
|
|
CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-names interrupts-extended interrupt-controller \\\#interrupt-cells interrupt-parent dmas dma-names assigned-clocks assigned-clock-rates assigned-clock-parents hwlocks"
|
|
CONFIG_ENV_IS_NOWHERE=y
|
|
CONFIG_ENV_IS_IN_MMC=y
|
|
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
|
|
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
|
# CONFIG_SPL_ENV_IS_NOWHERE is not set
|
|
CONFIG_DM_HWSPINLOCK=y
|
|
CONFIG_HWSPINLOCK_STM32=y
|
|
CONFIG_DM_I2C=y
|
|
CONFIG_SYS_I2C_STM32F7=y
|
|
CONFIG_LED=y
|
|
CONFIG_LED_GPIO=y
|
|
CONFIG_STM32_FMC2_EBI=y
|
|
CONFIG_SUPPORT_EMMC_BOOT=y
|
|
CONFIG_STM32_SDMMC2=y
|
|
CONFIG_PHY_REALTEK=y
|
|
CONFIG_DM_ETH=y
|
|
CONFIG_DWC_ETH_QOS=y
|
|
CONFIG_PHY=y
|
|
CONFIG_PINCONF=y
|
|
# CONFIG_SPL_PINCTRL_FULL is not set
|
|
CONFIG_PINCTRL_STMFX=y
|
|
CONFIG_DM_PMIC=y
|
|
# CONFIG_SPL_PMIC_CHILDREN is not set
|
|
CONFIG_PMIC_STPMIC1=y
|
|
CONFIG_DM_REGULATOR=y
|
|
CONFIG_DM_REGULATOR_FIXED=y
|
|
CONFIG_DM_REGULATOR_GPIO=y
|
|
CONFIG_REMOTEPROC_STM32_COPRO=y
|
|
CONFIG_DM_RTC=y
|
|
CONFIG_RTC_STM32=y
|
|
CONFIG_SERIAL_RX_BUFFER=y
|
|
CONFIG_SYSRESET_SYSCON=y
|
|
CONFIG_WDT=y
|
|
CONFIG_WDT_STM32MP=y
|
|
# CONFIG_BINMAN_FDT is not set
|
|
CONFIG_LZO=y
|
|
CONFIG_ERRNO_STR=y
|