leandrof/u-boot
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
bc97f48915
u-boot/include/configs/ep82xxm.h
Rob Herring f232950f82 config: remove platform CONFIG_SYS_HZ definition part 2/2 
Remove platform CONFIG_SYS_HZ definition for configs a-z*.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04 11:06:16 -05:00

385 lines
13 KiB
C
Raw Blame History

/*
* Copyright (C) 2006 Embedded Planet, LLC.
*
* U-Boot configuration for Embedded Planet EP82xxM boards.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#define CONFIG_MPC8260
#define CPU_ID_STR "MPC8270"
#define CONFIG_EP82XXM /* Embedded Planet EP82xxM H 1.0 board */
/* 256MB SDRAM / 64MB FLASH */
#define CONFIG_SYS_TEXT_BASE 0xFFF00000
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
/* Allow serial number (serial#) and MAC address (ethaddr) to be overwritten */
#define CONFIG_ENV_OVERWRITE
/*
* Select serial console configuration
*
* If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
* CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
* for SCC).
*/
#define CONFIG_CONS_ON_SMC /* Console is on SMC */
#undef CONFIG_CONS_ON_SCC /* It's not on SCC */
#undef CONFIG_CONS_NONE /* It's not on external UART */
#define CONFIG_CONS_INDEX 1 /* SMC1 is used for console */
#define CONFIG_SYS_BCSR 0xFA000000
/*
* Select ethernet configuration
*
* If either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected,
* then CONFIG_ETHER_INDEX must be set to the channel number (1-4 for
* SCC, 1-3 for FCC)
*
* If CONFIG_ETHER_NONE is defined, then either the ethernet routines
* must be defined elsewhere (as for the console), or CONFIG_CMD_NET
* must be unset.
*/
#undef CONFIG_ETHER_ON_SCC /* Ethernet is not on SCC */
#define CONFIG_ETHER_ON_FCC /* Ethernet is on FCC */
#undef CONFIG_ETHER_NONE /* No external Ethernet */
#define CONFIG_ETHER_ON_FCC2
#define CONFIG_ETHER_ON_FCC3
#define CONFIG_SYS_CMXFCR_MASK3 (CMXFCR_FC3 | CMXFCR_RF3CS_MSK | CMXFCR_TF3CS_MSK)
#define CONFIG_SYS_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK15 | CMXFCR_TF3CS_CLK16)
#define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
#define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
#define CONFIG_SYS_CPMFCR_RAMTYPE 0
#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB)
#define CONFIG_MII /* MII PHY management */
#define CONFIG_BITBANGMII /* Bit-banged MDIO interface */
/*
* GPIO pins used for bit-banged MII communications
*/
#define MDIO_PORT 0 /* Not used - implemented in BCSR */
#define MDIO_ACTIVE (*(vu_char *)(CONFIG_SYS_BCSR + 8) &= 0xFB)
#define MDIO_TRISTATE (*(vu_char *)(CONFIG_SYS_BCSR + 8) |= 0x04)
#define MDIO_READ (*(vu_char *)(CONFIG_SYS_BCSR + 8) & 1)
#define MDIO(bit) if(bit) *(vu_char *)(CONFIG_SYS_BCSR + 8) |= 0x01; \
else *(vu_char *)(CONFIG_SYS_BCSR + 8) &= 0xFE
#define MDC(bit) if(bit) *(vu_char *)(CONFIG_SYS_BCSR + 8) |= 0x02; \
else *(vu_char *)(CONFIG_SYS_BCSR + 8) &= 0xFD
#define MIIDELAY udelay(1)
#ifndef CONFIG_8260_CLKIN
#define CONFIG_8260_CLKIN 66000000 /* in Hz */
#endif
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_VXWORKS_MAC_PTR 0x4300 /* Pass Ethernet MAC to VxWorks */
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_ECHO
#define CONFIG_CMD_I2C
#define CONFIG_CMD_IMMAP
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#define CONFIG_CMD_DATE
#define CONFIG_CMD_DTT
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_PCI
#define CONFIG_CMD_DIAG
#define CONFIG_ETHADDR 00:10:EC:00:88:65
#define CONFIG_HAS_ETH1
#define CONFIG_ETH1ADDR 00:10:EC:80:88:65
#define CONFIG_IPADDR 10.0.0.245
#define CONFIG_HOSTNAME EP82xxM
#define CONFIG_SERVERIP 10.0.0.26
#define CONFIG_GATEWAYIP 10.0.0.1
#define CONFIG_NETMASK 255.255.255.0
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#define CONFIG_ENV_IN_OWN_SECT 1
#define CONFIG_AUTO_COMPLETE 1
#define CONFIG_EXTRA_ENV_SETTINGS "ethprime=FCC3"
#if defined(CONFIG_CMD_KGDB)
#undef CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */
#define CONFIG_KGDB_ON_SCC /* define if kgdb on SCC */
#undef CONFIG_KGDB_NONE /* define if kgdb on something else */
#define CONFIG_KGDB_INDEX 1 /* which serial channel for kgdb */
#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port at */
#endif
#define CONFIG_BZIP2 /* include support for bzip2 compressed images */
#undef CONFIG_WATCHDOG /* disable platform specific watchdog */
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT "ep82xxm=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
/*
* Define here the location of the environment variables (FLASH or EEPROM).
* Note: DENX encourages to use redundant environment in FLASH.
*/
#if 1
#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
#else
#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
#endif
/*-----------------------------------------------------------------------
* FLASH related
*----------------------------------------------------------------------*/
#define CONFIG_SYS_FLASH_BASE 0xFC000000
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector in flinfo */
#ifdef CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_SECT_SIZE 0x20000
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
#endif /* CONFIG_ENV_IS_IN_FLASH */
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
/* EEPROM Configuration */
#define CONFIG_SYS_EEPROM_SIZE 0x1000
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
#ifdef CONFIG_ENV_IS_IN_EEPROM
#define CONFIG_ENV_SIZE 0x200 /* Size of Environment vars */
#define CONFIG_ENV_OFFSET 0x0
#endif /* CONFIG_ENV_IS_IN_EEPROM */
/* RTC Configuration */
#define CONFIG_RTC_M41T11 1 /* uses a M41T81 */
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
#define CONFIG_M41T11_BASE_YEAR 1900
/* I2C SYSMON (LM75) */
#define CONFIG_DTT_LM75 1
#define CONFIG_DTT_SENSORS {0}
#define CONFIG_SYS_DTT_MAX_TEMP 70
#define CONFIG_SYS_DTT_LOW_TEMP -30
#define CONFIG_SYS_DTT_HYSTERESIS 3
/*-----------------------------------------------------------------------
* NVRAM Configuration
*-----------------------------------------------------------------------
*/
#define CONFIG_SYS_NVRAM_BASE_ADDR 0xFA080000
#define CONFIG_SYS_NVRAM_SIZE (128*1024)-16
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
*/
/* General PCI */
#define CONFIG_PCI /* include pci support */
#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CONFIG_PCI_BOOTDELAY 0
/* PCI Memory map (if different from default map */
#define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE /* Local base */
#define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000 /* PCI base */
#define CONFIG_SYS_PICMR0_MASK_ATTRIB (PICMR_MASK_512MB | PICMR_ENABLE | \
PICMR_PREFETCH_EN)
/*
* These are the windows that allow the CPU to access PCI address space.
* All three PCI master windows, which allow the CPU to access PCI
* prefetch, non prefetch, and IO space (see below), must all fit within
* these windows.
*/
/*
* Master window that allows the CPU to access PCI Memory (prefetch).
* This window will be setup with the second set of Outbound ATU registers
* in the bridge.
*/
#define CONFIG_SYS_PCI_MSTR_MEM_LOCAL 0x80000000 /* Local base */
#define CONFIG_SYS_PCI_MSTR_MEM_BUS 0x80000000 /* PCI base */
#define CONFIG_SYS_CPU_PCI_MEM_START PCI_MSTR_MEM_LOCAL
#define CONFIG_SYS_PCI_MSTR_MEM_SIZE 0x20000000 /* 512MB */
#define CONFIG_SYS_POCMR0_MASK_ATTRIB (POCMR_MASK_512MB | POCMR_ENABLE | POCMR_PREFETCH_EN)
/*
* Master window that allows the CPU to access PCI Memory (non-prefetch).
* This window will be setup with the second set of Outbound ATU registers
* in the bridge.
*/
#define CONFIG_SYS_PCI_MSTR_MEMIO_LOCAL 0xA0000000 /* Local base */
#define CONFIG_SYS_PCI_MSTR_MEMIO_BUS 0xA0000000 /* PCI base */
#define CONFIG_SYS_CPU_PCI_MEMIO_START PCI_MSTR_MEMIO_LOCAL
#define CONFIG_SYS_PCI_MSTR_MEMIO_SIZE 0x20000000 /* 512MB */
#define CONFIG_SYS_POCMR1_MASK_ATTRIB (POCMR_MASK_512MB | POCMR_ENABLE)
/*
* Master window that allows the CPU to access PCI IO space.
* This window will be setup with the first set of Outbound ATU registers
* in the bridge.
*/
#define CONFIG_SYS_PCI_MSTR_IO_LOCAL 0xF6000000 /* Local base */
#define CONFIG_SYS_PCI_MSTR_IO_BUS 0x00000000 /* PCI base */
#define CONFIG_SYS_CPU_PCI_IO_START PCI_MSTR_IO_LOCAL
#define CONFIG_SYS_PCI_MSTR_IO_SIZE 0x02000000 /* 64MB */
#define CONFIG_SYS_POCMR2_MASK_ATTRIB (POCMR_MASK_32MB | POCMR_ENABLE | POCMR_PCI_IO)
/* PCIBR0 - for PCI IO*/
#define CONFIG_SYS_PCI_MSTR0_LOCAL CONFIG_SYS_PCI_MSTR_IO_LOCAL /* Local base */
#define CONFIG_SYS_PCIMSK0_MASK ~(CONFIG_SYS_PCI_MSTR_IO_SIZE - 1U) /* Size of window */
/* PCIBR1 - prefetch and non-prefetch regions joined together */
#define CONFIG_SYS_PCI_MSTR1_LOCAL CONFIG_SYS_PCI_MSTR_MEM_LOCAL
#define CONFIG_SYS_PCIMSK1_MASK ~(CONFIG_SYS_PCI_MSTR_MEM_SIZE + CONFIG_SYS_PCI_MSTR_MEMIO_SIZE - 1U)
#define CONFIG_SYS_DIRECT_FLASH_TFTP
#if defined(CONFIG_CMD_JFFS2)
#define CONFIG_SYS_JFFS2_FIRST_BANK 0
#define CONFIG_SYS_JFFS2_NUM_BANKS CONFIG_SYS_MAX_FLASH_BANKS
#define CONFIG_SYS_JFFS2_FIRST_SECTOR 0
#define CONFIG_SYS_JFFS2_LAST_SECTOR 62
#define CONFIG_SYS_JFFS2_SORT_FRAGMENTS
#define CONFIG_SYS_JFFS_CUSTOM_PART
#endif
#if defined(CONFIG_CMD_I2C)
#define CONFIG_HARD_I2C 1 /* To enable I2C support */
#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed */
#define CONFIG_SYS_I2C_SLAVE 0x7F /* I2C slave address */
#endif
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
#define CONFIG_SYS_RAMBOOT
#endif
#define CONFIG_SYS_MONITOR_LEN (512 << 10) /* Reserve 256KB for Monitor */
#define CONFIG_SYS_DEFAULT_IMMR 0x00010000
#define CONFIG_SYS_IMMR 0xF0000000
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in DPRAM */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/* Hard reset configuration word */
#define CONFIG_SYS_HRCW_MASTER 0 /*0x1C800641*/ /* Not used - provided by CPLD */
/* No slaves */
#define CONFIG_SYS_HRCW_SLAVE1 0
#define CONFIG_SYS_HRCW_SLAVE2 0
#define CONFIG_SYS_HRCW_SLAVE3 0
#define CONFIG_SYS_HRCW_SLAVE4 0
#define CONFIG_SYS_HRCW_SLAVE5 0
#define CONFIG_SYS_HRCW_SLAVE6 0
#define CONFIG_SYS_HRCW_SLAVE7 0
#define CONFIG_SYS_MALLOC_LEN (4096 << 10) /* Reserve 4 MB for malloc() */
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPUs */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
#define CONFIG_SYS_HID0_INIT 0
#define CONFIG_SYS_HID0_FINAL 0
#define CONFIG_SYS_HID2 0
#define CONFIG_SYS_SIUMCR 0x02610000
#define CONFIG_SYS_SYPCR 0xFFFF0689
#define CONFIG_SYS_BCR 0x8080E000
#define CONFIG_SYS_SCCR 0x00000001
#define CONFIG_SYS_RMR 0
#define CONFIG_SYS_TMCNTSC 0x000000C3
#define CONFIG_SYS_PISCR 0x00000083
#define CONFIG_SYS_RCCR 0
#define CONFIG_SYS_MPTPR 0x0A00
#define CONFIG_SYS_PSDMR 0xC432246E
#define CONFIG_SYS_PSRT 0x32
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_SYS_SDRAM_BR (CONFIG_SYS_SDRAM_BASE | 0x00000041)
#define CONFIG_SYS_SDRAM_OR 0xF0002900
#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | 0x00001801)
#define CONFIG_SYS_OR0_PRELIM 0xFC000882
#define CONFIG_SYS_BR4_PRELIM (CONFIG_SYS_BCSR | 0x00001001)
#define CONFIG_SYS_OR4_PRELIM 0xFFF00050
#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100
#endif /* __CONFIG_H */
Reference in New Issue View Git Blame Copy Permalink