b8fea5e8dd
I'm working on getting OpenBSD to run on the Atmel SAMA5D3 Xplained. OpenBSD uses an EFI bootloader, which requires the "load" command to work, since "fatload" doesn't initialize the EFI memory addresses properly. To get "load" on the SAMA5D3 version of U-Boot, I propose adding the CONFIG_CMD_FS_GENERIC option. Signed-off-by: Greg Czerniak <greg@czerniak.info>
86 lines
2.0 KiB
Plaintext
86 lines
2.0 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_ARCH_AT91=y
|
|
CONFIG_SYS_TEXT_BASE=0x26f00000
|
|
CONFIG_TARGET_SAMA5D3_XPLAINED=y
|
|
CONFIG_SPL_GPIO_SUPPORT=y
|
|
CONFIG_SPL_LIBCOMMON_SUPPORT=y
|
|
CONFIG_SPL_LIBGENERIC_SUPPORT=y
|
|
CONFIG_SYS_MALLOC_F_LEN=0x2000
|
|
CONFIG_SPL_MMC_SUPPORT=y
|
|
CONFIG_SPL_SERIAL_SUPPORT=y
|
|
CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
|
|
CONFIG_SPL=y
|
|
CONFIG_DEBUG_UART_BOARD_INIT=y
|
|
CONFIG_DEBUG_UART_BASE=0xffffee00
|
|
CONFIG_DEBUG_UART_CLOCK=132000000
|
|
CONFIG_SPL_FAT_SUPPORT=y
|
|
CONFIG_SPL_LIBDISK_SUPPORT=y
|
|
CONFIG_DEBUG_UART=y
|
|
CONFIG_ENV_VARS_UBOOT_CONFIG=y
|
|
CONFIG_NR_DRAM_BANKS=1
|
|
CONFIG_FIT=y
|
|
CONFIG_SD_BOOT=y
|
|
CONFIG_BOOTDELAY=3
|
|
CONFIG_USE_BOOTARGS=y
|
|
CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk root=/dev/mmcblk0p2 rw rootwait"
|
|
# CONFIG_DISPLAY_BOARDINFO is not set
|
|
CONFIG_SPL_SEPARATE_BSS=y
|
|
CONFIG_HUSH_PARSER=y
|
|
CONFIG_CMD_BOOTZ=y
|
|
# CONFIG_CMD_FLASH is not set
|
|
# CONFIG_CMD_LOADS is not set
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_NAND=y
|
|
CONFIG_CMD_NAND_TRIMFFS=y
|
|
CONFIG_CMD_USB=y
|
|
CONFIG_CMD_DHCP=y
|
|
CONFIG_CMD_MII=y
|
|
CONFIG_CMD_PING=y
|
|
CONFIG_CMD_EXT4=y
|
|
CONFIG_CMD_EXT4_WRITE=y
|
|
CONFIG_CMD_FAT=y
|
|
CONFIG_CMD_MTDPARTS=y
|
|
CONFIG_CMD_UBI=y
|
|
CONFIG_OF_CONTROL=y
|
|
CONFIG_SPL_OF_CONTROL=y
|
|
CONFIG_DEFAULT_DEVICE_TREE="at91-sama5d3_xplained"
|
|
CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-parent dmas dma-names"
|
|
CONFIG_ENV_IS_IN_FAT=y
|
|
CONFIG_DM=y
|
|
CONFIG_SPL_DM=y
|
|
CONFIG_SPL_DM_SEQ_ALIAS=y
|
|
CONFIG_CLK=y
|
|
CONFIG_SPL_CLK=y
|
|
CONFIG_CLK_AT91=y
|
|
CONFIG_AT91_UTMI=y
|
|
CONFIG_AT91_H32MX=y
|
|
CONFIG_DM_GPIO=y
|
|
CONFIG_AT91_GPIO=y
|
|
CONFIG_DM_MMC=y
|
|
CONFIG_GENERIC_ATMEL_MCI=y
|
|
CONFIG_NAND=y
|
|
CONFIG_NAND_ATMEL=y
|
|
CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER=y
|
|
CONFIG_DM_ETH=y
|
|
CONFIG_MACB=y
|
|
CONFIG_PINCTRL=y
|
|
CONFIG_SPL_PINCTRL=y
|
|
CONFIG_PINCTRL_AT91=y
|
|
CONFIG_DM_SERIAL=y
|
|
CONFIG_DEBUG_UART_ATMEL=y
|
|
CONFIG_DEBUG_UART_ANNOUNCE=y
|
|
CONFIG_ATMEL_USART=y
|
|
CONFIG_TIMER=y
|
|
CONFIG_SPL_TIMER=y
|
|
CONFIG_ATMEL_PIT_TIMER=y
|
|
CONFIG_USB=y
|
|
CONFIG_DM_USB=y
|
|
CONFIG_USB_EHCI_HCD=y
|
|
CONFIG_USB_STORAGE=y
|
|
CONFIG_CMD_FS_GENERIC=y
|
|
CONFIG_W1=y
|
|
CONFIG_W1_GPIO=y
|
|
CONFIG_W1_EEPROM=y
|
|
CONFIG_W1_EEPROM_DS24XXX=y
|
|
CONFIG_OF_LIBFDT_OVERLAY=y
|