1a0afe1fad
We do not have to define CONFIG_4xx in board config headers because it is defined in arch/powerpc/cpu/ppc4xx/config.mk. include/configs/JSE.h defines "CONFIG_4x", not "CONFIG_4xx". I believe it is a typo because "CONFIG_4x" is not used at all in other files. So, I also deleted "CONFIG_4x" in include/configs/JSE.h. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
321 lines
12 KiB
C
321 lines
12 KiB
C
/*
|
|
* (C) Copyright 2001
|
|
* Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
/*
|
|
* board/config.h - configuration options, board specific
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
* (easy to change)
|
|
*/
|
|
|
|
#define CONFIG_405GP 1 /* This is a PPC405 CPU */
|
|
#define CONFIG_CPCI405 1 /* ...on a CPCI405 board */
|
|
|
|
#define CONFIG_SYS_TEXT_BASE 0xFFFC0000
|
|
|
|
#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
|
|
#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
|
|
|
|
#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */
|
|
|
|
#define CONFIG_BAUDRATE 9600
|
|
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
|
|
|
|
#undef CONFIG_BOOTARGS
|
|
#undef CONFIG_BOOTCOMMAND
|
|
|
|
#define CONFIG_PREBOOT /* enable preboot variable */
|
|
|
|
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
|
|
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
|
|
|
|
#define CONFIG_PPC4xx_EMAC
|
|
#define CONFIG_MII 1 /* MII PHY management */
|
|
#define CONFIG_PHY_ADDR 0 /* PHY address */
|
|
#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
|
|
#define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */
|
|
|
|
#undef CONFIG_HAS_ETH1
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_SUBNETMASK
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
#define CONFIG_BOOTP_HOSTNAME
|
|
#define CONFIG_BOOTP_BOOTPATH
|
|
#define CONFIG_BOOTP_DNS
|
|
#define CONFIG_BOOTP_DNS2
|
|
#define CONFIG_BOOTP_SEND_HOSTNAME
|
|
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
#include <config_cmd_default.h>
|
|
|
|
#define CONFIG_CMD_DHCP
|
|
#define CONFIG_CMD_PCI
|
|
#define CONFIG_CMD_IRQ
|
|
#define CONFIG_CMD_IDE
|
|
#define CONFIG_CMD_FAT
|
|
#define CONFIG_CMD_ELF
|
|
#define CONFIG_CMD_MII
|
|
#define CONFIG_CMD_EEPROM
|
|
|
|
|
|
#define CONFIG_MAC_PARTITION
|
|
#define CONFIG_DOS_PARTITION
|
|
|
|
#define CONFIG_SUPPORT_VFAT
|
|
|
|
#undef CONFIG_WATCHDOG /* watchdog disabled */
|
|
|
|
#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
|
|
#undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
|
|
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
#else
|
|
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
#endif
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
|
|
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
|
|
|
|
#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */
|
|
|
|
#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
|
|
#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
|
|
|
|
#define CONFIG_CONS_INDEX 1 /* Use UART0 */
|
|
#define CONFIG_SYS_NS16550
|
|
#define CONFIG_SYS_NS16550_SERIAL
|
|
#define CONFIG_SYS_NS16550_REG_SIZE 1
|
|
#define CONFIG_SYS_NS16550_CLK get_serial_clock()
|
|
|
|
#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */
|
|
#define CONFIG_SYS_BASE_BAUD 691200
|
|
|
|
/* The following table includes the supported baudrates */
|
|
#define CONFIG_SYS_BAUDRATE_TABLE \
|
|
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
|
|
57600, 115200, 230400, 460800, 921600 }
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
|
|
#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
|
|
|
|
#define CONFIG_LOOPW 1 /* enable loopw command */
|
|
|
|
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PCI stuff
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
|
|
#define PCI_HOST_FORCE 1 /* configure as pci host */
|
|
#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
|
|
|
|
#define CONFIG_PCI /* include pci support */
|
|
#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
|
|
#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
|
|
#define CONFIG_PCI_PNP /* do pci plug-and-play */
|
|
/* resource configuration */
|
|
|
|
#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
|
|
|
|
#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
|
|
|
|
#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
|
|
|
|
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
|
|
#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
|
|
#define CONFIG_SYS_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */
|
|
#define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
|
|
#define CONFIG_SYS_PCI_PTM1LA (bd->bi_memstart) /* point to sdram */
|
|
#define CONFIG_SYS_PCI_PTM1MS (~(bd->bi_memsize - 1) | 1) /* memsize, enable hard-wired to 1 */
|
|
#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
|
|
#define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */
|
|
#define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
|
|
#define CONFIG_SYS_PCI_PTM2PCI (bd->bi_memsize) /* host use this pci address */
|
|
|
|
#define CONFIG_PCI_4xx_PTM_OVERWRITE 1 /* overwrite PTMx settings by env */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* IDE/ATA stuff
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
|
|
#undef CONFIG_IDE_LED /* no led for ide supported */
|
|
#undef CONFIG_IDE_RESET /* no reset for ide supported */
|
|
|
|
#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */
|
|
#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
|
|
|
|
#define CONFIG_SYS_ATA_BASE_ADDR 0xF0100000
|
|
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
|
|
|
|
#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
|
|
#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
|
|
#define CONFIG_SYS_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Start addresses for the final memory configuration
|
|
* (Set up by the startup code)
|
|
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
|
|
*/
|
|
#define CONFIG_SYS_SDRAM_BASE 0x00000000
|
|
#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_TEXT_BASE
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
|
|
#define CONFIG_SYS_MONITOR_LEN (~(CONFIG_SYS_TEXT_BASE) + 1)
|
|
#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
|
/*-----------------------------------------------------------------------
|
|
* FLASH organization
|
|
*/
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
|
|
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
|
|
|
|
#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
|
|
#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
|
|
#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
|
|
/*
|
|
* The following defines are added for buggy IOP480 byte interface.
|
|
* All other boards should use the standard values (CPCI405 etc.)
|
|
*/
|
|
#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */
|
|
#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */
|
|
#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */
|
|
|
|
#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
|
|
|
|
#define CONFIG_SYS_NVRAM_BASE_ADDR 0xf0200000 /* NVRAM base address */
|
|
#define CONFIG_SYS_NVRAM_SIZE (32*1024) /* NVRAM size */
|
|
#define CONFIG_SYS_VXWORKS_MAC_PTR (CONFIG_SYS_NVRAM_BASE_ADDR+0x6900) /* VxWorks eth-addr*/
|
|
|
|
#if 1 /* Use NVRAM for environment variables */
|
|
/*-----------------------------------------------------------------------
|
|
* NVRAM organization
|
|
*/
|
|
#define CONFIG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */
|
|
#define CONFIG_ENV_SIZE 0x1000 /* Size of Environment vars */
|
|
#define CONFIG_ENV_ADDR \
|
|
(CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE) /* Env */
|
|
|
|
#else /* Use EEPROM for environment variables */
|
|
|
|
#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
|
|
#define CONFIG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
|
|
#define CONFIG_ENV_SIZE 0x400 /* 1024 bytes may be used for env vars */
|
|
/* total size of a CAT24WC08 is 1024 bytes */
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* I2C EEPROM (CAT24WC08) for environment
|
|
*/
|
|
#define CONFIG_SYS_I2C
|
|
#define CONFIG_SYS_I2C_PPC4XX
|
|
#define CONFIG_SYS_I2C_PPC4XX_CH0
|
|
#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
|
|
#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
|
|
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
|
|
/* mask of address bits that overflow into the "EEPROM chip address" */
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
|
|
/* 16 byte page write mode using*/
|
|
/* last 4 bits of the address */
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
|
|
|
|
/*
|
|
* Init Memory Controller:
|
|
*
|
|
* BR0/1 and OR0/1 (FLASH)
|
|
*/
|
|
|
|
#define FLASH_BASE0_PRELIM 0xFF800000 /* FLASH bank #0 */
|
|
#define FLASH_BASE1_PRELIM 0xFFC00000 /* FLASH bank #1 */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* External Bus Controller (EBC) Setup
|
|
*/
|
|
|
|
/* Memory Bank 0 (Flash Bank 0) initialization */
|
|
#define CONFIG_SYS_EBC_PB0AP 0x92015480
|
|
#define CONFIG_SYS_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
|
|
|
|
/* Memory Bank 1 (Flash Bank 1) initialization */
|
|
#define CONFIG_SYS_EBC_PB1AP 0x92015480
|
|
#define CONFIG_SYS_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
|
|
|
|
/* Memory Bank 2 (CAN0, 1, 2, Codeswitch) initialization */
|
|
#define CONFIG_SYS_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
|
|
#define CONFIG_SYS_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
|
|
|
|
/* Memory Bank 3 (CompactFlash IDE) initialization */
|
|
#define CONFIG_SYS_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
|
|
#define CONFIG_SYS_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
|
|
|
|
/* Memory Bank 4 (NVRAM) initialization */
|
|
#define CONFIG_SYS_EBC_PB4AP 0x01005280 /* TWT=2,WBN=1,WBF=1,TH=1,SOR=1 */
|
|
#define CONFIG_SYS_EBC_PB4CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */
|
|
|
|
/* Memory Bank 5 (Quart) initialization */
|
|
#define CONFIG_SYS_EBC_PB5AP 0x04005B80 /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/
|
|
#define CONFIG_SYS_EBC_PB5CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* FPGA stuff
|
|
*/
|
|
|
|
/* FPGA program pin configuration */
|
|
#define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
|
|
#define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
|
|
#define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
|
|
#define CONFIG_SYS_FPGA_INIT 0x00400000 /* FPGA init pin (ppc input) */
|
|
#define CONFIG_SYS_FPGA_DONE 0x00800000 /* FPGA done pin (ppc input) */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Definitions for initial stack pointer and data area (in data cache)
|
|
*/
|
|
#if 1 /* test-only */
|
|
#define CONFIG_SYS_INIT_DCACHE_CS 7 /* use cs # 7 for data cache memory */
|
|
|
|
#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 /* use data cache */
|
|
#else
|
|
#define CONFIG_SYS_INIT_RAM_ADDR 0x00df0000 /* inside of SDRAM */
|
|
#endif
|
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
#endif /* __CONFIG_H */
|