2fe88d4522
This converts the following to Kconfig: CONFIG_FLASH_CFI_DRIVER CONFIG_SYS_FLASH_USE_BUFFER_WRITE CONFIG_FLASH_CFI_MTD CONFIG_SYS_FLASH_PROTECTION CONFIG_SYS_FLASH_CFI Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-migrate] Signed-off-by: Tom Rini <trini@konsulko.com>
134 lines
4.3 KiB
C
134 lines
4.3 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Configuation settings for the Renesas Solutions ECOVEC board
|
|
*
|
|
* Copyright (C) 2009 - 2011 Renesas Solutions Corp.
|
|
* Copyright (C) 2009 Kuninori Morimoto <morimoto.kuninori@renesas.com>
|
|
* Copyright (C) 2010, 2011 Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
*/
|
|
|
|
#ifndef __ECOVEC_H
|
|
#define __ECOVEC_H
|
|
|
|
/*
|
|
* Address Interface BusWidth
|
|
*-----------------------------------------
|
|
* 0x0000_0000 U-Boot 16bit
|
|
* 0x0004_0000 Linux romImage 16bit
|
|
* 0x0014_0000 MTD for Linux 16bit
|
|
* 0x0400_0000 Internal I/O 16/32bit
|
|
* 0x0800_0000 DRAM 32bit
|
|
* 0x1800_0000 MFI 16bit
|
|
*/
|
|
|
|
#define CONFIG_CPU_SH7724 1
|
|
|
|
#define CONFIG_ECOVEC_ROMIMAGE_ADDR 0xA0040000
|
|
|
|
#define CONFIG_DISPLAY_BOARDINFO
|
|
#undef CONFIG_SHOW_BOOT_PROGRESS
|
|
|
|
/* I2C */
|
|
#define CONFIG_SYS_I2C
|
|
#define CONFIG_SYS_I2C_SH
|
|
#define CONFIG_SYS_I2C_SLAVE 0x7F
|
|
#define CONFIG_SYS_I2C_SH_NUM_CONTROLLERS 2
|
|
#define CONFIG_SYS_I2C_SH_BASE0 0xA4470000
|
|
#define CONFIG_SYS_I2C_SH_SPEED0 100000
|
|
#define CONFIG_SYS_I2C_SH_BASE1 0xA4750000
|
|
#define CONFIG_SYS_I2C_SH_SPEED1 100000
|
|
#define CONFIG_SH_I2C_DATA_HIGH 4
|
|
#define CONFIG_SH_I2C_DATA_LOW 5
|
|
#define CONFIG_SH_I2C_CLOCK 41666666
|
|
|
|
/* Ether */
|
|
#define CONFIG_SH_ETHER_USE_PORT (0)
|
|
#define CONFIG_SH_ETHER_PHY_ADDR (0x1f)
|
|
#define CONFIG_PHY_SMSC 1
|
|
#define CONFIG_BITBANGMII
|
|
#define CONFIG_BITBANGMII_MULTI
|
|
#define CONFIG_SH_ETHER_PHY_MODE PHY_INTERFACE_MODE_MII
|
|
|
|
/* USB / R8A66597 */
|
|
#define CONFIG_USB_R8A66597_HCD
|
|
#define CONFIG_R8A66597_BASE_ADDR 0xA4D80000
|
|
#define CONFIG_R8A66597_XTAL 0x0000 /* 12MHz */
|
|
#define CONFIG_R8A66597_LDRV 0x8000 /* 3.3V */
|
|
#define CONFIG_R8A66597_ENDIAN 0x0000 /* little */
|
|
#define CONFIG_SUPERH_ON_CHIP_R8A66597
|
|
|
|
/* undef to save memory */
|
|
/* Monitor Command Prompt */
|
|
/* Buffer size for Console output */
|
|
#define CONFIG_SYS_PBSIZE 256
|
|
/* List of legal baudrate settings for this board */
|
|
#define CONFIG_SYS_BAUDRATE_TABLE { 115200 }
|
|
|
|
/* SCIF */
|
|
#define CONFIG_SCIF 1
|
|
#define CONFIG_CONS_SCIF0 1
|
|
|
|
/* Suppress display of console information at boot */
|
|
|
|
/* SDRAM */
|
|
#define CONFIG_SYS_SDRAM_BASE (0x88000000)
|
|
#define CONFIG_SYS_SDRAM_SIZE (256 * 1024 * 1024)
|
|
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 16 * 1024 * 1024)
|
|
|
|
#define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE)
|
|
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 200 * 1024 * 1024)
|
|
/* Enable alternate, more extensive, memory test */
|
|
/* Scratch address used by the alternate memory test */
|
|
#undef CONFIG_SYS_MEMTEST_SCRATCH
|
|
|
|
/* Enable temporary baudrate change while serial download */
|
|
#undef CONFIG_SYS_LOADS_BAUD_CHANGE
|
|
|
|
/* FLASH */
|
|
#undef CONFIG_SYS_FLASH_QUIET_TEST
|
|
#define CONFIG_SYS_FLASH_EMPTY_INFO
|
|
#define CONFIG_SYS_FLASH_BASE (0xA0000000)
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 512
|
|
|
|
/* if you use all NOR Flash , you change dip-switch. Please see Manual. */
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1
|
|
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
|
|
|
|
/* Timeout for Flash erase operations (in ms) */
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT (3 * 1000)
|
|
/* Timeout for Flash write operations (in ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT (3 * 1000)
|
|
/* Timeout for Flash set sector lock bit operations (in ms) */
|
|
#define CONFIG_SYS_FLASH_LOCK_TOUT (3 * 1000)
|
|
/* Timeout for Flash clear lock bit operations (in ms) */
|
|
#define CONFIG_SYS_FLASH_UNLOCK_TOUT (3 * 1000)
|
|
|
|
/*
|
|
* Use hardware flash sectors protection instead
|
|
* of U-Boot software protection
|
|
*/
|
|
#undef CONFIG_SYS_DIRECT_FLASH_TFTP
|
|
|
|
/* Address of u-boot image in Flash (NOT run time address in SDRAM) ?!? */
|
|
#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE)
|
|
/* Monitor size */
|
|
#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
|
|
/* Size of DRAM reserved for malloc() use */
|
|
#define CONFIG_SYS_MALLOC_LEN (256 * 1024)
|
|
#define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024)
|
|
|
|
/* ENV setting */
|
|
#define CONFIG_ENV_OVERWRITE 1
|
|
#define CONFIG_ENV_SECT_SIZE (128 * 1024)
|
|
#define CONFIG_ENV_SIZE (CONFIG_ENV_SECT_SIZE)
|
|
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN)
|
|
/* Offset of env Flash sector relative to CONFIG_SYS_FLASH_BASE */
|
|
#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE)
|
|
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SECT_SIZE)
|
|
|
|
/* Board Clock */
|
|
#define CONFIG_SYS_CLK_FREQ 41666666
|
|
#define CONFIG_SH_SCIF_CLK_FREQ CONFIG_SYS_CLK_FREQ
|
|
|
|
#endif /* __ECOVEC_H */
|