3b36b38f50
The ESM (Error Signal Monitor) is used on certain PMIC versions to handle error signals propagating from rest of the system. If these reach the PMIC, it is typically a last resort fatal error which requires a system reset. The ESM driver does the proper configuration for the ESM module to reach this end goal. Initially, only TPS65941 PMIC is supported for this. Signed-off-by: Tero Kristo <t-kristo@ti.com>
77 lines
2.7 KiB
Makefile
77 lines
2.7 KiB
Makefile
# SPDX-License-Identifier: GPL-2.0+
|
|
#
|
|
# (C) Copyright 2000-2007
|
|
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
|
|
|
|
obj-$(CONFIG_MISC) += misc-uclass.o
|
|
|
|
obj-$(CONFIG_$(SPL_TPL_)CROS_EC) += cros_ec.o
|
|
obj-$(CONFIG_$(SPL_TPL_)CROS_EC_SANDBOX) += cros_ec_sandbox.o
|
|
obj-$(CONFIG_$(SPL_TPL_)CROS_EC_LPC) += cros_ec_lpc.o
|
|
|
|
ifndef CONFIG_SPL_BUILD
|
|
obj-$(CONFIG_SANDBOX) += sandbox_adder.o
|
|
obj-$(CONFIG_CROS_EC_I2C) += cros_ec_i2c.o
|
|
obj-$(CONFIG_CROS_EC_SPI) += cros_ec_spi.o
|
|
obj-$(CONFIG_SANDBOX) += p2sb_sandbox.o p2sb_emul.o
|
|
obj-$(CONFIG_SANDBOX) += swap_case.o
|
|
endif
|
|
|
|
ifdef CONFIG_DM_I2C
|
|
ifndef CONFIG_SPL_BUILD
|
|
obj-$(CONFIG_SANDBOX) += i2c_eeprom_emul.o
|
|
endif
|
|
endif
|
|
ifdef CONFIG_SPL_OF_PLATDATA
|
|
ifdef CONFIG_SPL_BUILD
|
|
obj-$(CONFIG_SANDBOX) += spltest_sandbox.o
|
|
endif
|
|
endif
|
|
obj-$(CONFIG_ALI152X) += ali512x.o
|
|
obj-$(CONFIG_ALTERA_SYSID) += altera_sysid.o
|
|
obj-$(CONFIG_ATSHA204A) += atsha204a-i2c.o
|
|
obj-$(CONFIG_CBMEM_CONSOLE) += cbmem_console.o
|
|
obj-$(CONFIG_DS4510) += ds4510.o
|
|
obj-$(CONFIG_FSL_DEVICE_DISABLE) += fsl_devdis.o
|
|
obj-$(CONFIG_FSL_IFC) += fsl_ifc.o
|
|
obj-$(CONFIG_FSL_IIM) += fsl_iim.o
|
|
obj-$(CONFIG_FSL_MC9SDZ60) += mc9sdz60.o
|
|
obj-$(CONFIG_FSL_SEC_MON) += fsl_sec_mon.o
|
|
obj-$(CONFIG_FS_LOADER) += fs_loader.o
|
|
obj-$(CONFIG_GDSYS_IOEP) += gdsys_ioep.o
|
|
obj-$(CONFIG_GDSYS_RXAUI_CTRL) += gdsys_rxaui_ctrl.o
|
|
obj-$(CONFIG_GDSYS_SOC) += gdsys_soc.o
|
|
obj-$(CONFIG_IRQ) += irq-uclass.o
|
|
obj-$(CONFIG_SANDBOX) += irq_sandbox.o
|
|
obj-$(CONFIG_$(SPL_)I2C_EEPROM) += i2c_eeprom.o
|
|
obj-$(CONFIG_IHS_FPGA) += ihs_fpga.o
|
|
obj-$(CONFIG_IMX8) += imx8/
|
|
obj-$(CONFIG_LED_STATUS) += status_led.o
|
|
obj-$(CONFIG_LED_STATUS_GPIO) += gpio_led.o
|
|
obj-$(CONFIG_MPC83XX_SERDES) += mpc83xx_serdes.o
|
|
obj-$(CONFIG_MXC_OCOTP) += mxc_ocotp.o
|
|
obj-$(CONFIG_MXS_OCOTP) += mxs_ocotp.o
|
|
obj-$(CONFIG_NUVOTON_NCT6102D) += nuvoton_nct6102d.o
|
|
obj-$(CONFIG_P2SB) += p2sb-uclass.o
|
|
obj-$(CONFIG_PCA9551_LED) += pca9551_led.o
|
|
obj-$(CONFIG_$(SPL_)PWRSEQ) += pwrseq-uclass.o
|
|
obj-$(CONFIG_QFW) += qfw.o
|
|
obj-$(CONFIG_ROCKCHIP_EFUSE) += rockchip-efuse.o
|
|
obj-$(CONFIG_ROCKCHIP_OTP) += rockchip-otp.o
|
|
obj-$(CONFIG_SANDBOX) += syscon_sandbox.o misc_sandbox.o
|
|
obj-$(CONFIG_SMSC_LPC47M) += smsc_lpc47m.o
|
|
obj-$(CONFIG_SMSC_SIO1007) += smsc_sio1007.o
|
|
obj-$(CONFIG_STM32MP_FUSE) += stm32mp_fuse.o
|
|
obj-$(CONFIG_STM32_RCC) += stm32_rcc.o
|
|
obj-$(CONFIG_SYS_DPAA_QBMAN) += fsl_portals.o
|
|
obj-$(CONFIG_TEGRA186_BPMP) += tegra186_bpmp.o
|
|
obj-$(CONFIG_TEGRA_CAR) += tegra_car.o
|
|
obj-$(CONFIG_TWL4030_LED) += twl4030_led.o
|
|
obj-$(CONFIG_VEXPRESS_CONFIG) += vexpress_config.o
|
|
obj-$(CONFIG_WINBOND_W83627) += winbond_w83627.o
|
|
obj-$(CONFIG_JZ4780_EFUSE) += jz4780_efuse.o
|
|
obj-$(CONFIG_MICROCHIP_FLEXCOM) += microchip_flexcom.o
|
|
obj-$(CONFIG_K3_AVS0) += k3_avs.o
|
|
obj-$(CONFIG_ESM_K3) += k3_esm.o
|
|
obj-$(CONFIG_ESM_PMIC) += esm_pmic.o
|