65cc0e2a65
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do not easily transition to Kconfig. In many cases they likely should come from the device tree instead. Move these out of CONFIG namespace and in to CFG namespace. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
224 lines
6.3 KiB
C
224 lines
6.3 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Configuation settings for the Sentec Cobra Board.
|
|
*
|
|
* (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
|
|
*/
|
|
|
|
/* ---
|
|
* Version: U-Boot 1.0.0 - initial release for Sentec COBRA5272 board
|
|
* Date: 2004-03-29
|
|
* Author: Florian Schlote
|
|
*
|
|
* For a description of configuration options please refer also to the
|
|
* general u-boot-1.x.x/README file
|
|
* ---
|
|
*/
|
|
|
|
/* ---
|
|
* board/config.h - configuration options, board specific
|
|
* ---
|
|
*/
|
|
|
|
#ifndef _CONFIG_COBRA5272_H
|
|
#define _CONFIG_COBRA5272_H
|
|
|
|
/* ---
|
|
* Defines processor clock - important for correct timings concerning serial
|
|
* interface etc.
|
|
* ---
|
|
*/
|
|
|
|
#define CFG_SYS_CLK 66000000
|
|
#define CFG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */
|
|
|
|
/* ---
|
|
* Define baudrate for UART1 (console output, tftp, ...)
|
|
* default value of CONFIG_BAUDRATE for Sentec board: 19200 baud
|
|
* CFG_SYS_BAUDRATE_TABLE defines values that can be selected in u-boot command
|
|
* interface
|
|
* ---
|
|
*/
|
|
|
|
#define CFG_SYS_UART_PORT (0)
|
|
|
|
/* ---
|
|
* set "#if 0" to "#if 1" if (Hardware)-WATCHDOG should be enabled & change
|
|
* timeout acc. to your needs
|
|
* #define CONFIG_WATCHDOG_TIMEOUT x , x is timeout in milliseconds, e. g. 10000
|
|
* for 10 sec
|
|
* ---
|
|
*/
|
|
|
|
#if 0
|
|
#define CONFIG_WATCHDOG_TIMEOUT 10000 /* timeout in milliseconds */
|
|
#endif
|
|
|
|
/* ---
|
|
* CONFIG_MONITOR_IS_IN_RAM defines if u-boot is started from a different
|
|
* bootloader residing in flash ('chainloading'); if you want to use
|
|
* chainloading or want to compile a u-boot binary that can be loaded into
|
|
* RAM via BDM set
|
|
* "#if 0" to "#if 1"
|
|
* You will need a first stage bootloader then, e. g. colilo or a working BDM
|
|
* cable (Background Debug Mode)
|
|
*
|
|
* Setting #if 0: u-boot will start from flash and relocate itself to RAM
|
|
*
|
|
* Please do not forget to modify the setting of CONFIG_TEXT_BASE
|
|
* in board/cobra5272/config.mk accordingly (#if 0: 0xffe00000; #if 1: 0x20000)
|
|
*
|
|
* ---
|
|
*/
|
|
|
|
#if 0
|
|
#define CONFIG_MONITOR_IS_IN_RAM /* monitor is started from a preloader */
|
|
#endif
|
|
|
|
/* ---
|
|
* Configuration for environment
|
|
* Environment is embedded in u-boot in the second sector of the flash
|
|
* ---
|
|
*/
|
|
|
|
#define LDS_BOARD_TEXT \
|
|
. = DEFINED(env_offset) ? env_offset : .; \
|
|
env/embedded.o(.text);
|
|
|
|
/*
|
|
*-----------------------------------------------------------------------------
|
|
* Define user parameters that have to be customized most likely
|
|
*-----------------------------------------------------------------------------
|
|
*/
|
|
|
|
/*AUTOBOOT settings - booting images automatically by u-boot after power on*/
|
|
|
|
/* The following settings will be contained in the environment block ; if you
|
|
want to use a neutral environment all those settings can be manually set in
|
|
u-boot: 'set' command */
|
|
|
|
#if 0
|
|
|
|
enter a valid image address in flash */
|
|
|
|
/* User network settings */
|
|
|
|
#define CONFIG_IPADDR 192.168.100.2 /* default board IP address */
|
|
#define CONFIG_SERVERIP 192.168.100.1 /* default tftp server IP address */
|
|
|
|
#endif
|
|
|
|
/*---*/
|
|
|
|
/*
|
|
*-----------------------------------------------------------------------------
|
|
* End of user parameters to be customized
|
|
*-----------------------------------------------------------------------------
|
|
*/
|
|
|
|
/* ---
|
|
* Defines memory range for test
|
|
* ---
|
|
*/
|
|
|
|
/* ---
|
|
* Low Level Configuration Settings
|
|
* (address mappings, register initial values, etc.)
|
|
* You should know what you are doing if you make changes here.
|
|
* ---
|
|
*/
|
|
|
|
/* ---
|
|
* Base register address
|
|
* ---
|
|
*/
|
|
|
|
#define CFG_SYS_MBAR 0x10000000 /* Register Base Addrs */
|
|
|
|
/* ---
|
|
* System Conf. Reg. & System Protection Reg.
|
|
* ---
|
|
*/
|
|
|
|
#define CFG_SYS_SCR 0x0003
|
|
#define CFG_SYS_SPR 0xffff
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Definitions for initial stack pointer and data area (in internal SRAM)
|
|
*/
|
|
#define CFG_SYS_INIT_RAM_ADDR 0x20000000
|
|
#define CFG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Start addresses for the final memory configuration
|
|
* (Set up by the startup code)
|
|
* Please note that CFG_SYS_SDRAM_BASE _must_ start at 0
|
|
*/
|
|
#define CFG_SYS_SDRAM_BASE 0x00000000
|
|
|
|
/*
|
|
*-------------------------------------------------------------------------
|
|
* RAM SIZE (is defined above)
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
|
|
/* #define CFG_SYS_SDRAM_SIZE 16 */
|
|
|
|
/*
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
|
|
#define CFG_SYS_FLASH_BASE 0xffe00000
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization ??
|
|
*/
|
|
#define CFG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Cache Configuration
|
|
*/
|
|
|
|
#define ICACHE_STATUS (CFG_SYS_INIT_RAM_ADDR + \
|
|
CFG_SYS_INIT_RAM_SIZE - 8)
|
|
#define DCACHE_STATUS (CFG_SYS_INIT_RAM_ADDR + \
|
|
CFG_SYS_INIT_RAM_SIZE - 4)
|
|
#define CFG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI)
|
|
#define CFG_SYS_CACHE_ACR0 (CFG_SYS_SDRAM_BASE | \
|
|
CF_ADDRMASK(CFG_SYS_SDRAM_SIZE) | \
|
|
CF_ACR_EN | CF_ACR_SM_ALL)
|
|
#define CFG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \
|
|
CF_CACR_DISD | CF_CACR_INVI | \
|
|
CF_CACR_CEIB | CF_CACR_DCM | \
|
|
CF_CACR_EUSP)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* LED config
|
|
*/
|
|
#define LED_STAT_0 0xffff /*all LEDs off*/
|
|
#define LED_STAT_1 0xfffe
|
|
#define LED_STAT_2 0xfffd
|
|
#define LED_STAT_3 0xfffb
|
|
#define LED_STAT_4 0xfff7
|
|
#define LED_STAT_5 0xffef
|
|
#define LED_STAT_6 0xffdf
|
|
#define LED_STAT_7 0xff00 /*all LEDs on*/
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Port configuration (GPIO)
|
|
*/
|
|
#define CFG_SYS_PACNT 0x00000000 /* PortA control reg.: All pins are external
|
|
GPIO*/
|
|
#define CFG_SYS_PADDR 0x00FF /* PortA direction reg.: PA7 to PA0 are outputs
|
|
(1^=output, 0^=input) */
|
|
#define CFG_SYS_PADAT LED_STAT_0 /* PortA value reg.: Turn all LED off */
|
|
#define CFG_SYS_PBCNT 0x55554155 /* PortB control reg.: Ethernet/UART
|
|
configuration */
|
|
#define CFG_SYS_PBDDR 0x0000 /* PortB direction: All pins configured as inputs */
|
|
#define CFG_SYS_PBDAT 0x0000 /* PortB value reg. */
|
|
#define CFG_SYS_PDCNT 0x00000000 /* PortD control reg. */
|
|
|
|
#endif /* _CONFIG_COBRA5272_H */
|