leandrof/u-boot
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
a7b6ef05bf
u-boot/include/configs/gr_ep2s60.h
Joe Hershberger ef0f2f5752 Move defaults from config_cmd_default.h to Kconfig 
This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-06-25 22:18:34 -04:00

323 lines
10 KiB
C
Raw Blame History

/* Configuration header file for Gaisler Research AB's Template
* design (GPL Open Source SPARC/LEON3 96MHz) for Altera NIOS
* Development board Stratix II edition, with the FPGA device
* EP2S60.
*
* (C) Copyright 2003-2005
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* (C) Copyright 2008
* Daniel Hellstrom, Gaisler Research, daniel@gaisler.com.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H__
#define __CONFIG_H__
/*
* High Level Configuration Options
* (easy to change)
*/
/* Altera NIOS Development board, Stratix II board */
#define CONFIG_GR_EP2S60 1
/* CPU / AMBA BUS configuration */
#define CONFIG_SYS_CLK_FREQ 96000000 /* 96MHz */
/* Number of SPARC register windows */
#define CONFIG_SYS_SPARC_NWINDOWS 8
/* Define this is the GR-2S60-MEZZ mezzanine is available and you
* want to use the USB and GRETH functionality of the board
*/
#undef GR_2S60_MEZZ
#ifdef GR_2S60_MEZZ
#define USE_GRETH 1
#define USE_GRUSB 1
#endif
/*
* Serial console configuration
*/
#define CONFIG_BAUDRATE 38400 /* ... at 38400 bps */
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
/* Partitions */
#define CONFIG_DOS_PARTITION
#define CONFIG_MAC_PARTITION
#define CONFIG_ISO_PARTITION
/*
* Supported commands
*/
#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_AMBAPP
#define CONFIG_CMD_PING
#define CONFIG_CMD_DIAG
#define CONFIG_CMD_IRQ
/* USB support */
#if USE_GRUSB
#define CONFIG_USB_UHCI
#define CONFIG_CMD_FAT
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_USB
#define CONFIG_USB_STORAGE
/* Enable needed helper functions */
#define CONFIG_SYS_STDIO_DEREGISTER /* needs stdio_deregister */
#endif
/*
* Autobooting
*/
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#define CONFIG_PREBOOT "echo;" \
"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"nfsargs=setenv bootargs console=ttyS0,38400 root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs console=ttyS0,${baudrate} root=/dev/ram rw\0" \
"addip=setenv bootargs ${bootargs} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off panic=1\0" \
"flash_nfs=run nfsargs addip;" \
"bootm ${kernel_addr}\0" \
"flash_self=run ramargs addip;" \
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
"net_nfs=tftp 40000000 ${bootfile};run nfsargs addip;bootm\0" \
"scratch=40800000\0" \
"getkernel=tftpboot $(scratch) $(bootfile)\0" \
"bootargs=console=ttyS0,38400 root=/dev/nfs rw nfsroot=192.168.0.20:/export/rootfs ip=192.168.0.207:192.168.0.20:192.168.0.1:255.255.255.0:ml401:eth0\0" \
""
#define CONFIG_NETMASK 255.255.255.0
#define CONFIG_GATEWAYIP 192.168.0.1
#define CONFIG_SERVERIP 192.168.0.20
#define CONFIG_IPADDR 192.168.0.207
#define CONFIG_ROOTPATH "/export/rootfs"
#define CONFIG_HOSTNAME ml401
#define CONFIG_BOOTFILE "/uImage"
#define CONFIG_BOOTCOMMAND "run flash_self"
/* Memory MAP
*
* Flash:
* |--------------------------------|
* | 0x00000000 Text & Data & BSS | *
* | for Monitor | *
* | ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~| *
* | UNUSED / Growth | * 256kb
* |--------------------------------|
* | 0x00050000 Base custom area | *
* | kernel / FS | *
* | | * Rest of Flash
* |~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~|
* | END-0x00008000 Environment | * 32kb
* |--------------------------------|
*
*
*
* Main Memory:
* |--------------------------------|
* | UNUSED / scratch area |
* | |
* | |
* | |
* | |
* |--------------------------------|
* | Monitor .Text / .DATA / .BSS | * 512kb
* | Relocated! | *
* |--------------------------------|
* | Monitor Malloc | * 128kb (contains relocated environment)
* |--------------------------------|
* | Monitor/kernel STACK | * 64kb
* |--------------------------------|
* | Page Table for MMU systems | * 2k
* |--------------------------------|
* | PROM Code accessed from Linux | * 6kb-128b
* |--------------------------------|
* | Global data (avail from kernel)| * 128b
* |--------------------------------|
*
*/
/*
* Flash configuration (8,16 or 32 MB)
* TEXT base always at 0xFFF00000
* ENV_ADDR always at 0xFFF40000
* FLASH_BASE at 0xFC000000 for 64 MB
* 0xFE000000 for 32 MB
* 0xFF000000 for 16 MB
* 0xFF800000 for 8 MB
*/
/*#define CONFIG_SYS_NO_FLASH 1*/
#define CONFIG_SYS_FLASH_BASE 0x00000000
#define CONFIG_SYS_FLASH_SIZE 0x00400000 /* FPGA Bit file is in top of FLASH, we only ues the bottom 4Mb */
#define PHYS_FLASH_SECT_SIZE 0x00010000 /* 64 KB sectors */
#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max num of sects on one chip */
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */
#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
#define CONFIG_SYS_FLASH_LOCK_TOUT 5 /* Timeout for Flash Set Lock Bit (in ms) */
#define CONFIG_SYS_FLASH_UNLOCK_TOUT 10000 /* Timeout for Flash Clear Lock Bits (in ms) */
#define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */
/*** CFI CONFIG ***/
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
/* Bypass cache when reading regs from flash memory */
#define CONFIG_SYS_FLASH_CFI_BYPASS_READ
/* Buffered writes (32byte/go) instead of single accesses */
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
/*
* Environment settings
*/
/*#define CONFIG_ENV_IS_NOWHERE 1*/
#define CONFIG_ENV_IS_IN_FLASH 1
/* CONFIG_ENV_ADDR need to be at sector boundary */
#define CONFIG_ENV_SIZE 0x8000
#define CONFIG_ENV_SECT_SIZE 0x20000
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE+CONFIG_SYS_FLASH_SIZE-CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_OVERWRITE 1
/*
* Memory map
*/
#define CONFIG_SYS_SDRAM_BASE 0x40000000
#define CONFIG_SYS_SDRAM_SIZE 0x02000000
#define CONFIG_SYS_SDRAM_END (CONFIG_SYS_SDRAM_BASE+CONFIG_SYS_SDRAM_SIZE)
/* no SRAM available */
#undef CONFIG_SYS_SRAM_BASE
#undef CONFIG_SYS_SRAM_SIZE
#define CONFIG_SYS_RAM_BASE CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_RAM_SIZE CONFIG_SYS_SDRAM_SIZE
#define CONFIG_SYS_RAM_END CONFIG_SYS_SDRAM_END
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_SDRAM_END - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_PROM_SIZE (8192-GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_PROM_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET-CONFIG_SYS_PROM_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_PROM_OFFSET-32)
#define CONFIG_SYS_STACK_SIZE (0x10000-32)
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
# define CONFIG_SYS_RAMBOOT 1
#endif
#define CONFIG_SYS_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */
#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
#define CONFIG_SYS_MALLOC_END (CONFIG_SYS_INIT_SP_OFFSET-CONFIG_SYS_STACK_SIZE)
#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MALLOC_END-CONFIG_SYS_MALLOC_LEN)
/* relocated monitor area */
#define CONFIG_SYS_RELOC_MONITOR_MAX_END CONFIG_SYS_MALLOC_BASE
#define CONFIG_SYS_RELOC_MONITOR_BASE (CONFIG_SYS_RELOC_MONITOR_MAX_END-CONFIG_SYS_MONITOR_LEN)
/* make un relocated address from relocated address */
#define UN_RELOC(address) (address-(CONFIG_SYS_RELOC_MONITOR_BASE-CONFIG_SYS_TEXT_BASE))
/*
* Ethernet configuration uses on board SMC91C111, however if a mezzanine
* with a PHY is attached the GRETH can be used on this board.
* Define USE_GRETH in order to use the mezzanine provided PHY with the
* onchip GRETH network MAC, note that this is not supported by the
* template design.
*/
#ifndef USE_GRETH
/* USE SMC91C111 MAC */
#define CONFIG_SMC91111 1
#define CONFIG_SMC91111_BASE 0x20000300 /* chip select 3 */
#define CONFIG_SMC_USE_32_BIT 1 /* 32 bit bus */
#undef CONFIG_SMC_91111_EXT_PHY /* we use internal phy */
/*#define CONFIG_SHOW_ACTIVITY*/
#define CONFIG_NET_RETRY_COUNT 10 /* # of retries */
#else
/* USE GRETH Ethernet Driver */
#define CONFIG_GRETH 1
#endif
#define CONFIG_PHY_ADDR 0x00
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
/*-----------------------------------------------------------------------
* USB stuff
*-----------------------------------------------------------------------
*/
#define CONFIG_USB_CLOCK 0x0001BBBB
#define CONFIG_USB_CONFIG 0x00005000
/***** Gaisler GRLIB IP-Cores Config ********/
/* AMBA Plug & Play info display on startup */
/*#define CONFIG_SYS_AMBAPP_PRINT_ON_STARTUP*/
#define CONFIG_SYS_GRLIB_SDRAM 0
/* See, GRLIB Docs (grip.pdf) on how to set up
* These the memory controller registers.
*/
#define CONFIG_SYS_GRLIB_MEMCFG1 (0x10f800ff | (1<<11))
#define CONFIG_SYS_GRLIB_MEMCFG2 0x00000000
#define CONFIG_SYS_GRLIB_MEMCFG3 0x00000000
#define CONFIG_SYS_GRLIB_FT_MEMCFG1 (0x10f800ff | (1<<11))
#define CONFIG_SYS_GRLIB_FT_MEMCFG2 0x00000000
#define CONFIG_SYS_GRLIB_FT_MEMCFG3 0x00000000
#define CONFIG_SYS_GRLIB_DDR_CFG 0xa900830a
#define CONFIG_SYS_GRLIB_DDR2_CFG1 0x00000000
#define CONFIG_SYS_GRLIB_DDR2_CFG3 0x00000000
/* Calculate scaler register value from default baudrate */
#define CONFIG_SYS_GRLIB_APBUART_SCALER \
((((CONFIG_SYS_CLK_FREQ*10)/(CONFIG_BAUDRATE*8))-5)/10)
/* Identification string */
#define CONFIG_IDENT_STRING "GAISLER LEON3 EP2S60"
/* default kernel command line */
#define CONFIG_DEFAULT_KERNEL_COMMAND_LINE "console=ttyS0,38400\0\0"
#endif /* __CONFIG_H */
Reference in New Issue View Git Blame Copy Permalink