08574ed339
This converts the following to Kconfig: CONFIG_SYS_MONITOR_LEN To do this, we set a default of 0 for everyone because there are a number of cases where we define CONFIG_SYS_MONITOR_LEN but the only impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN + CONFIG_ENV_SIZE, so we must continue to allow all boards to set this value. Update the SPL code to use 200 KB as the default raw U-Boot size directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
109 lines
2.6 KiB
Plaintext
109 lines
2.6 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_COUNTER_FREQUENCY=12500000
|
|
CONFIG_TARGET_LS1021AIOT=y
|
|
CONFIG_TEXT_BASE=0x82000000
|
|
CONFIG_SYS_MALLOC_LEN=0x1002000
|
|
CONFIG_SPL_LIBCOMMON_SUPPORT=y
|
|
CONFIG_SPL_LIBGENERIC_SUPPORT=y
|
|
CONFIG_NR_DRAM_BANKS=1
|
|
CONFIG_ENV_SIZE=0x2000
|
|
CONFIG_ENV_OFFSET=0x100000
|
|
CONFIG_SYS_I2C_MXC_I2C1=y
|
|
CONFIG_SYS_I2C_MXC_I2C2=y
|
|
CONFIG_SYS_I2C_MXC_I2C3=y
|
|
CONFIG_DM_GPIO=y
|
|
CONFIG_DEFAULT_DEVICE_TREE="ls1021a-iot-duart"
|
|
CONFIG_SPL_TEXT_BASE=0x10000000
|
|
CONFIG_SPL_MMC=y
|
|
CONFIG_SPL_SERIAL=y
|
|
CONFIG_SPL=y
|
|
CONFIG_SYS_LOAD_ADDR=0x82000000
|
|
CONFIG_AHCI=y
|
|
# CONFIG_DEEP_SLEEP is not set
|
|
CONFIG_LAYERSCAPE_NS_ACCESS=y
|
|
CONFIG_PCIE1=y
|
|
CONFIG_PCIE2=y
|
|
CONFIG_SYS_MONITOR_LEN=524288
|
|
CONFIG_OF_BOARD_SETUP=y
|
|
CONFIG_OF_STDOUT_VIA_ALIAS=y
|
|
CONFIG_RAMBOOT_PBL=y
|
|
CONFIG_SYS_FSL_PBL_PBI="board/freescale/ls1021aiot/ls102xa_pbi.cfg"
|
|
CONFIG_SYS_FSL_PBL_RCW="board/freescale/ls1021aiot/ls102xa_rcw_sd.cfg"
|
|
CONFIG_SD_BOOT=y
|
|
CONFIG_SD_BOOT_QSPI=y
|
|
CONFIG_ARCH_MISC_INIT=y
|
|
CONFIG_BOARD_EARLY_INIT_F=y
|
|
CONFIG_MISC_INIT_R=y
|
|
CONFIG_ID_EEPROM=y
|
|
CONFIG_SPL_MAX_SIZE=0x1a000
|
|
CONFIG_SPL_PAD_TO=0x1c000
|
|
CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
|
|
CONFIG_SPL_BSS_START_ADDR=0x80100000
|
|
CONFIG_SPL_BSS_MAX_SIZE=0x80000
|
|
CONFIG_SPL_FSL_PBL=y
|
|
# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
|
|
CONFIG_SPL_STACK=0x1001d000
|
|
CONFIG_SYS_SPL_MALLOC=y
|
|
CONFIG_HAS_CUSTOM_SPL_MALLOC_START=y
|
|
CONFIG_CUSTOM_SYS_SPL_MALLOC_ADDR=0x82080000
|
|
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
|
|
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0xe8
|
|
CONFIG_SPL_ENV_SUPPORT=y
|
|
CONFIG_SPL_I2C=y
|
|
CONFIG_SPL_MPC8XXX_INIT_DDR=y
|
|
CONFIG_SPL_WATCHDOG=y
|
|
CONFIG_SYS_CBSIZE=256
|
|
CONFIG_SYS_PBSIZE=276
|
|
CONFIG_CMD_BOOTZ=y
|
|
CONFIG_CMD_GREPENV=y
|
|
CONFIG_SYS_I2C_EEPROM_ADDR_LEN=2
|
|
CONFIG_CMD_MEMINFO=y
|
|
CONFIG_CMD_GPT=y
|
|
CONFIG_CMD_I2C=y
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_DHCP=y
|
|
CONFIG_CMD_MII=y
|
|
# CONFIG_CMD_MDIO is not set
|
|
CONFIG_CMD_PING=y
|
|
CONFIG_CMD_EXT2=y
|
|
CONFIG_CMD_FAT=y
|
|
# CONFIG_SPL_EFI_PARTITION is not set
|
|
CONFIG_OF_CONTROL=y
|
|
CONFIG_ENV_OVERWRITE=y
|
|
CONFIG_ENV_IS_IN_MMC=y
|
|
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
|
CONFIG_USE_ETHPRIME=y
|
|
CONFIG_ETHPRIME="eTSEC2"
|
|
CONFIG_SATA=y
|
|
CONFIG_SATA_CEVA=y
|
|
CONFIG_FSL_CAAM=y
|
|
CONFIG_DM_I2C=y
|
|
CONFIG_SPL_SYS_I2C_LEGACY=y
|
|
CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
|
|
CONFIG_SYS_I2C_EEPROM_ADDR=0x51
|
|
CONFIG_FSL_ESDHC=y
|
|
CONFIG_MTD=y
|
|
CONFIG_SPI_FLASH_ATMEL=y
|
|
CONFIG_SPI_FLASH_SPANSION=y
|
|
CONFIG_SPI_FLASH_STMICRO=y
|
|
CONFIG_PHY_ATHEROS=y
|
|
CONFIG_PHY_GIGE=y
|
|
CONFIG_E1000=y
|
|
CONFIG_MII=y
|
|
CONFIG_TSEC_ENET=y
|
|
CONFIG_NVME_PCI=y
|
|
CONFIG_PCI=y
|
|
CONFIG_DM_PCI_COMPAT=y
|
|
CONFIG_PCIE_LAYERSCAPE_RC=y
|
|
CONFIG_U_QE=y
|
|
CONFIG_SYS_QE_FW_ADDR=0xf40000
|
|
CONFIG_DM_SCSI=y
|
|
CONFIG_SYS_NS16550=y
|
|
CONFIG_SPI=y
|
|
CONFIG_DM_SPI=y
|
|
CONFIG_FSL_DSPI=y
|
|
CONFIG_FSL_QSPI=y
|
|
CONFIG_USB=y
|
|
CONFIG_USB_XHCI_HCD=y
|
|
CONFIG_USB_XHCI_DWC3=y
|