86cf1c8285
We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <trini@konsulko.com>
85 lines
2.1 KiB
C
85 lines
2.1 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* (C) Copyright 2005, Psyent Corporation <www.psyent.com>
|
|
* Scott McNutt <smcnutt@psyent.com>
|
|
* (C) Copyright 2010, Thomas Chou <thomas@wytron.com.tw>
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* BOARD/CPU
|
|
*/
|
|
|
|
/*
|
|
* SERIAL
|
|
*/
|
|
|
|
/*
|
|
* CFI Flash
|
|
*/
|
|
#define CONFIG_FLASH_CFI_DRIVER
|
|
#define CONFIG_SYS_CFI_FLASH_STATUS_POLL /* fix amd flash issue */
|
|
#define CONFIG_SYS_FLASH_CFI
|
|
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
|
|
#define CONFIG_SYS_FLASH_PROTECTION
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 1
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 512
|
|
|
|
/*
|
|
* NET options
|
|
*/
|
|
#define CONFIG_SYS_RX_ETH_BUFFER 0
|
|
#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
|
|
/*
|
|
* FDT options
|
|
*/
|
|
#define CONFIG_LMB
|
|
|
|
/*
|
|
* MEMORY ORGANIZATION
|
|
* -Monitor at top of sdram.
|
|
* -The heap is placed below the monitor
|
|
* -The stack is placed below the heap (&grows down).
|
|
*/
|
|
#define CONFIG_SYS_SDRAM_BASE 0xD0000000
|
|
#define CONFIG_SYS_SDRAM_SIZE 0x08000000
|
|
#define CONFIG_MONITOR_IS_IN_RAM
|
|
#define CONFIG_SYS_MONITOR_LEN 0x80000 /* Reserve 512k */
|
|
#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_SDRAM_BASE + \
|
|
CONFIG_SYS_SDRAM_SIZE - \
|
|
CONFIG_SYS_MONITOR_LEN)
|
|
#define CONFIG_SYS_MALLOC_LEN 0x20000
|
|
|
|
/*
|
|
* ENVIRONMENT -- Put environment in sector CONFIG_SYS_MONITOR_LEN above
|
|
* CONFIG_SYS_RESET_ADDR, since we assume the monitor is stored at the
|
|
* reset address, no? This will keep the environment in user region
|
|
* of flash. NOTE: the monitor length must be multiple of sector size
|
|
* (which is common practice).
|
|
*/
|
|
|
|
#define CONFIG_ENV_SIZE 0x20000 /* 128k, 1 sector */
|
|
#define CONFIG_ENV_OVERWRITE /* Serial change Ok */
|
|
#define CONFIG_ENV_ADDR (0xe2800000 + CONFIG_SYS_MONITOR_LEN)
|
|
|
|
/*
|
|
* MISC
|
|
*/
|
|
#define CONFIG_SYS_LOAD_ADDR 0xd4000000 /* Half of RAM */
|
|
#define CONFIG_LOADADDR CONFIG_SYS_LOAD_ADDR
|
|
#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
|
|
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MONITOR_BASE - \
|
|
CONFIG_ENV_SIZE - \
|
|
CONFIG_SYS_MALLOC_LEN - \
|
|
0x10000)
|
|
|
|
#endif /* __CONFIG_H */
|