81b9bb5fcb
The main difference between Pro4 and PXs2/LD6b is the Denali NAND IP version. This is now distinguished by DT. Merge the two defconfig files into uniphier_v7_defconfig. Update the README.uniphier too. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
183 lines
5.8 KiB
Plaintext
183 lines
5.8 KiB
Plaintext
U-Boot for UniPhier SoC family
|
|
==============================
|
|
|
|
|
|
Recommended toolchains
|
|
----------------------
|
|
|
|
The UniPhier platform is well tested with Linaro toolchains.
|
|
You can download pre-built toolchains from:
|
|
|
|
http://www.linaro.org/downloads/
|
|
|
|
|
|
Compile the source
|
|
------------------
|
|
|
|
The source can be configured and built with the following commands:
|
|
|
|
$ make <defconfig>
|
|
$ make CROSS_COMPILE=<toolchain-prefix> DEVICE_TREE=<device-tree>
|
|
|
|
The recommended <toolchain-prefix> is `arm-linux-gnueabihf-` for 32bit SoCs,
|
|
`aarch64-linux-gnu-` for 64bit SoCs, but you may wish to change it to use your
|
|
favorite compiler.
|
|
|
|
The following tables show <defconfig> and <device-tree> for each board.
|
|
|
|
32bit SoC boards:
|
|
|
|
Board | <defconfig> | <device-tree>
|
|
---------------|-----------------------------|------------------------------
|
|
LD4 reference | uniphier_ld4_sld8_defconfig | uniphier-ld4-ref (default)
|
|
sld8 reference | uniphier_ld4_sld8_defconfig | uniphier-sld8-def
|
|
Pro4 reference | uniphier_v7_defconfig | uniphier-pro4-ref
|
|
Pro4 Ace | uniphier_v7_defconfig | uniphier-pro4-ace
|
|
Pro4 Sanji | uniphier_v7_defconfig | uniphier-pro4-sanji
|
|
Pro5 4KBOX | uniphier_v7_defconfig | uniphier-pro5-4kbox
|
|
PXs2 Gentil | uniphier_v7_defconfig | uniphier-pxs2-gentil
|
|
PXs2 Vodka | uniphier_v7_defconfig | uniphier-pxs2-vodka (default)
|
|
LD6b reference | uniphier_v7_defconfig | uniphier-ld6b-ref
|
|
|
|
64bit SoC boards:
|
|
|
|
Board | <defconfig> | <device-tree>
|
|
---------------|-----------------------|----------------------------
|
|
LD11 reference | uniphier_v8_defconfig | uniphier-ld11-ref
|
|
LD11 Global | uniphier_v8_defconfig | uniphier-ld11-global
|
|
LD20 reference | uniphier_v8_defconfig | uniphier-ld20-ref (default)
|
|
LD20 Global | uniphier_v8_defconfig | uniphier-ld20-global
|
|
PXs3 reference | uniphier_v8_defconfig | uniphier-pxs3-ref
|
|
|
|
For example, to compile the source for PXs2 Vodka board, run the following:
|
|
|
|
$ make uniphier_v7_defconfig
|
|
$ make CROSS_COMPILE=arm-linux-gnueabihf- DEVICE_TREE=uniphier-pxs2-vodka
|
|
|
|
The device tree marked as (default) can be omitted. `uniphier-pxs2-vodka` is
|
|
the default device tree for the configuration `uniphier_v7_defconfig`, so the
|
|
following gives the same result.
|
|
|
|
$ make uniphier_v7_defconfig
|
|
$ make CROSS_COMPILE=arm-linux-gnueabihf-
|
|
|
|
|
|
Booting 32bit SoC boards
|
|
------------------------
|
|
|
|
The build command will generate the following:
|
|
- u-boot.bin
|
|
- spl/u-boot.bin
|
|
|
|
U-Boot can boot UniPhier 32bit SoC boards by itself. Flash the generated images
|
|
to the storage device (NAND or eMMC) on your board.
|
|
|
|
- spl/u-boot-spl.bin at the offset address 0x00000000
|
|
- u-boot.bin at the offset address 0x00020000
|
|
|
|
The `u-boot-with-spl.bin` is the concatenation of the two (with appropriate
|
|
padding), so you can also do:
|
|
|
|
- u-boot-with-spl.bin at the offset address 0x00000000
|
|
|
|
If a TFTP server is available, the images can be easily updated.
|
|
Just copy the u-boot-spl.bin and u-boot.bin to the TFTP public directory,
|
|
and run the following command at the U-Boot command line:
|
|
|
|
To update the images in NAND:
|
|
|
|
=> run nandupdate
|
|
|
|
To update the images in eMMC:
|
|
|
|
=> run emmcupdate
|
|
|
|
|
|
Booting 64bit SoC boards
|
|
------------------------
|
|
|
|
The build command will generate the following:
|
|
- u-boot.bin
|
|
|
|
However, U-Boot is not the first stage loader for UniPhier 64bit SoC boards.
|
|
U-Boot serves as a non-secure boot loader loaded by [ARM Trusted Firmware],
|
|
so you need to provide the `u-boot.bin` to the build command of ARM Trusted
|
|
Firmware.
|
|
|
|
[ARM Trusted Firmware]: https://github.com/ARM-software/arm-trusted-firmware
|
|
|
|
|
|
UniPhier specific commands
|
|
--------------------------
|
|
|
|
- pinmon (enabled by CONFIG_CMD_PINMON)
|
|
shows the boot mode pins that has been latched at the power-on reset
|
|
|
|
- ddrphy (enabled by CONFIG_CMD_DDRPHY_DUMP)
|
|
shows the DDR PHY parameters set by the PHY training
|
|
|
|
- ddrmphy (enabled by CONFIG_CMD_DDRMPHY_DUMP)
|
|
shows the DDR Multi PHY parameters set by the PHY training
|
|
|
|
|
|
Supported devices
|
|
-----------------
|
|
|
|
- UART (on-chip)
|
|
- NAND
|
|
- SD/eMMC
|
|
- USB 2.0 (EHCI)
|
|
- USB 3.0 (xHCI)
|
|
- GPIO
|
|
- LAN (on-board SMSC9118)
|
|
- I2C
|
|
- EEPROM (connected to the on-board I2C bus)
|
|
- Support card (SRAM, NOR flash, some peripherals)
|
|
|
|
|
|
Micro Support Card
|
|
------------------
|
|
|
|
The recommended bit switch settings are as follows:
|
|
|
|
SW2 OFF(1)/ON(0) Description
|
|
------------------------------------------
|
|
bit 1 <---- BKSZ[0]
|
|
bit 2 ----> BKSZ[1]
|
|
bit 3 <---- SoC Bus Width 16/32
|
|
bit 4 <---- SERIAL_SEL[0]
|
|
bit 5 ----> SERIAL_SEL[1]
|
|
bit 6 ----> BOOTSWAP_EN
|
|
bit 7 <---- CS1/CS5
|
|
bit 8 <---- SOC_SERIAL_DISABLE
|
|
|
|
SW8 OFF(1)/ON(0) Description
|
|
------------------------------------------
|
|
bit 1 <---- CS1_SPLIT
|
|
bit 2 <---- CASE9_ON
|
|
bit 3 <---- CASE10_ON
|
|
bit 4 Don't Care Reserve
|
|
bit 5 Don't Care Reserve
|
|
bit 6 Don't Care Reserve
|
|
bit 7 ----> BURST_EN
|
|
bit 8 ----> FLASHBUS32_16
|
|
|
|
The BKSZ[1:0] specifies the address range of memory slot and peripherals
|
|
as follows:
|
|
|
|
BKSZ Description RAM slot Peripherals
|
|
--------------------------------------------------------------------
|
|
0b00 15MB RAM / 1MB Peri 00000000-00efffff 00f00000-00ffffff
|
|
0b01 31MB RAM / 1MB Peri 00000000-01efffff 01f00000-01ffffff
|
|
0b10 64MB RAM / 1MB Peri 00000000-03efffff 03f00000-03ffffff
|
|
0b11 127MB RAM / 1MB Peri 00000000-07efffff 07f00000-07ffffff
|
|
|
|
Set BSKZ[1:0] to 0b01 for U-Boot.
|
|
This mode is the most handy because EA[24] is always supported by the save pin
|
|
mode of the system bus. On the other hand, EA[25] is not supported for some
|
|
newer SoCs. Even if it is, EA[25] is not connected on most of the boards.
|
|
|
|
--
|
|
Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Sep. 2017
|