d0748898d8
This converts the following to Kconfig: CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS And we remove the entries from the README for a number of already converted items. Signed-off-by: Tom Rini <trini@konsulko.com>
114 lines
3.0 KiB
Plaintext
114 lines
3.0 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_COUNTER_FREQUENCY=25000000
|
|
CONFIG_GIC_V3_ITS=y
|
|
CONFIG_TARGET_LS2080AQDS=y
|
|
CONFIG_SYS_TEXT_BASE=0x80400000
|
|
CONFIG_SYS_MALLOC_LEN=0x0220000
|
|
CONFIG_SYS_MALLOC_F_LEN=0x400
|
|
CONFIG_SPL_LIBCOMMON_SUPPORT=y
|
|
CONFIG_SPL_LIBGENERIC_SUPPORT=y
|
|
CONFIG_NR_DRAM_BANKS=3
|
|
CONFIG_ENV_SIZE=0x20000
|
|
CONFIG_ENV_OFFSET=0x300000
|
|
CONFIG_DEFAULT_DEVICE_TREE="fsl-ls2080a-qds"
|
|
CONFIG_SPL_TEXT_BASE=0x1800a000
|
|
CONFIG_FSL_LS_PPA=y
|
|
CONFIG_SPL_MMC=y
|
|
CONFIG_SPL_SERIAL=y
|
|
CONFIG_SPL_DRIVERS_MISC=y
|
|
CONFIG_SPL=y
|
|
CONFIG_AHCI=y
|
|
CONFIG_FSL_USE_PCA9547_MUX=y
|
|
CONFIG_FSL_QIXIS=y
|
|
CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
|
|
CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0
|
|
CONFIG_REMAKE_ELF=y
|
|
CONFIG_MP=y
|
|
CONFIG_FIT_VERBOSE=y
|
|
CONFIG_OF_BOARD_SETUP=y
|
|
CONFIG_OF_STDOUT_VIA_ALIAS=y
|
|
CONFIG_DYNAMIC_SYS_CLK_FREQ=y
|
|
CONFIG_SD_BOOT=y
|
|
CONFIG_BOOTDELAY=10
|
|
CONFIG_USE_BOOTARGS=y
|
|
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 ramdisk_size=0x2000000 default_hugepagesz=2m hugepagesz=2m hugepages=256"
|
|
CONFIG_BOOTCOMMAND="mmc read 0x80200000 0x6800 0x800; fsl_mc apply dpl 0x80200000 && mmc read $kernel_load $kernel_start $kernel_size && bootm $kernel_load"
|
|
CONFIG_RESET_PHY_R=y
|
|
CONFIG_SPL_MAX_SIZE=0x16000
|
|
CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
|
|
CONFIG_SPL_BSS_START_ADDR=0x80100000
|
|
CONFIG_SPL_BSS_MAX_SIZE=0x100000
|
|
# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
|
|
CONFIG_SPL_STACK=0x18009ff0
|
|
CONFIG_SYS_SPL_MALLOC=y
|
|
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
|
|
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x8b0
|
|
CONFIG_SPL_ENV_SUPPORT=y
|
|
CONFIG_SPL_I2C=y
|
|
CONFIG_SPL_MPC8XXX_INIT_DDR=y
|
|
CONFIG_SPL_TARGET="u-boot-with-spl.bin"
|
|
CONFIG_SYS_MAXARGS=64
|
|
CONFIG_SYS_PBSIZE=532
|
|
CONFIG_CMD_GREPENV=y
|
|
CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
|
|
CONFIG_CMD_I2C=y
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_NAND=y
|
|
CONFIG_CMD_PCI=y
|
|
CONFIG_CMD_USB=y
|
|
# CONFIG_CMD_SETEXPR is not set
|
|
CONFIG_CMD_CACHE=y
|
|
CONFIG_CMD_DATE=y
|
|
CONFIG_OF_CONTROL=y
|
|
CONFIG_OF_EMBED=y
|
|
CONFIG_ENV_OVERWRITE=y
|
|
CONFIG_ENV_IS_IN_MMC=y
|
|
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
|
CONFIG_USE_ETHPRIME=y
|
|
CONFIG_ETHPRIME="DPMAC1@xgmii"
|
|
CONFIG_NET_RANDOM_ETHADDR=y
|
|
CONFIG_DM=y
|
|
CONFIG_SATA=y
|
|
CONFIG_SATA_CEVA=y
|
|
CONFIG_DYNAMIC_DDR_CLK_FREQ=y
|
|
CONFIG_DIMM_SLOTS_PER_CTLR=2
|
|
CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS=2
|
|
CONFIG_DDR_ECC=y
|
|
CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y
|
|
CONFIG_SYS_FSL_DDR_INTLV_256B=y
|
|
CONFIG_SYS_I2C_LEGACY=y
|
|
CONFIG_SYS_I2C_EARLY_INIT=y
|
|
CONFIG_SYS_I2C_EEPROM_ADDR=0x57
|
|
CONFIG_FSL_ESDHC=y
|
|
CONFIG_ESDHC_DETECT_QUIRK=y
|
|
CONFIG_MTD=y
|
|
CONFIG_MTD_RAW_NAND=y
|
|
CONFIG_NAND_FSL_IFC=y
|
|
CONFIG_SYS_NAND_ONFI_DETECTION=y
|
|
CONFIG_DM_SPI_FLASH=y
|
|
# CONFIG_SPI_FLASH_BAR is not set
|
|
CONFIG_SPI_FLASH_SPANSION=y
|
|
CONFIG_PHYLIB=y
|
|
CONFIG_PHYLIB_10G=y
|
|
CONFIG_PHY_REALTEK=y
|
|
CONFIG_PHY_TERANETICS=y
|
|
CONFIG_PHY_VITESSE=y
|
|
CONFIG_FSL_MEMAC=y
|
|
CONFIG_SYS_MEMAC_LITTLE_ENDIAN=y
|
|
CONFIG_PHY_GIGE=y
|
|
CONFIG_E1000=y
|
|
CONFIG_MII=y
|
|
CONFIG_NVME_PCI=y
|
|
CONFIG_PCI=y
|
|
CONFIG_DM_PCI_COMPAT=y
|
|
CONFIG_PCIE_LAYERSCAPE_RC=y
|
|
CONFIG_RTC_ENABLE_32KHZ_OUTPUT=y
|
|
CONFIG_DM_SCSI=y
|
|
CONFIG_SYS_NS16550=y
|
|
CONFIG_SPI=y
|
|
CONFIG_DM_SPI=y
|
|
CONFIG_FSL_QSPI=y
|
|
CONFIG_USB=y
|
|
CONFIG_USB_XHCI_HCD=y
|
|
CONFIG_USB_XHCI_DWC3=y
|