c4c3fa98ac
After this change it would be possible to use 'mtd' command to get access
to XEA's SPI-NOR partitions by name (e.g. SPL), not by offsets.
To enable this feature the CONFIG_SPI_FLASH_MTD needs to be defined in the
Kconfig, not in xea.h.
=> mtd list
=> mtd read spl-boot-data1 ${loadaddr} 0x0 4
=> md.l ${loadaddr} 1
Signed-off-by: Lukasz Majewski <lukma@denx.de>
113 lines
2.7 KiB
Plaintext
113 lines
2.7 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_SPL_SYS_THUMB_BUILD=y
|
|
CONFIG_ARCH_MX28=y
|
|
CONFIG_SYS_TEXT_BASE=0x40002000
|
|
CONFIG_SYS_MALLOC_F_LEN=0x800
|
|
CONFIG_SPL_GPIO=y
|
|
CONFIG_SPL_LIBCOMMON_SUPPORT=y
|
|
CONFIG_SPL_LIBGENERIC_SUPPORT=y
|
|
CONFIG_NR_DRAM_BANKS=1
|
|
CONFIG_IMX_CONFIG=""
|
|
CONFIG_DM_GPIO=y
|
|
CONFIG_SPL_DM_SPI=y
|
|
CONFIG_DEFAULT_DEVICE_TREE="imx28-xea"
|
|
CONFIG_SPL_TEXT_BASE=0x1000
|
|
CONFIG_TARGET_XEA=y
|
|
CONFIG_SPL_MMC=y
|
|
CONFIG_SPL_SERIAL=y
|
|
CONFIG_SPL_SYS_MALLOC_F_LEN=0x1000
|
|
CONFIG_SPL=y
|
|
CONFIG_ENV_OFFSET_REDUND=0x90000
|
|
CONFIG_SPL_SPI_FLASH_SUPPORT=y
|
|
CONFIG_SPL_SPI=y
|
|
CONFIG_SPL_PAYLOAD="u-boot.img"
|
|
CONFIG_SYS_LOAD_ADDR=0x42000000
|
|
CONFIG_FIT=y
|
|
CONFIG_TIMESTAMP=y
|
|
CONFIG_OF_BOARD_SETUP=y
|
|
CONFIG_USE_BOOTARGS=y
|
|
CONFIG_BOOTARGS="console=ttyAMA0,115200n8"
|
|
CONFIG_USE_BOOTCOMMAND=y
|
|
CONFIG_BOOTCOMMAND="run ${bootpri} ; run ${bootsec}"
|
|
CONFIG_USE_PREBOOT=y
|
|
CONFIG_PREBOOT="run prebootcmd"
|
|
CONFIG_BOARD_EARLY_INIT_F=y
|
|
CONFIG_SPL_BOARD_INIT=y
|
|
# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
|
|
CONFIG_SPL_SYS_MALLOC_SIMPLE=y
|
|
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
|
|
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x0
|
|
CONFIG_SUPPORT_EMMC_BOOT_OVERRIDE_PART_CONFIG=y
|
|
CONFIG_SPL_DMA=y
|
|
CONFIG_SPL_MMC_TINY=y
|
|
CONFIG_SPL_DM_SPI_FLASH=y
|
|
CONFIG_SPL_OS_BOOT=y
|
|
CONFIG_SPL_FALCON_BOOT_MMCSD=y
|
|
CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR=0x800
|
|
CONFIG_SPL_SPI_LOAD=y
|
|
CONFIG_SYS_SPI_U_BOOT_OFFS=0x10000
|
|
CONFIG_SPL_YMODEM_SUPPORT=y
|
|
CONFIG_HUSH_PARSER=y
|
|
CONFIG_CMD_SPL=y
|
|
CONFIG_CMD_ASKENV=y
|
|
CONFIG_CMD_GREPENV=y
|
|
CONFIG_CMD_DM=y
|
|
CONFIG_CMD_GPIO=y
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_MTD=y
|
|
# CONFIG_CMD_PINMUX is not set
|
|
CONFIG_CMD_SPI=y
|
|
CONFIG_CMD_DHCP=y
|
|
CONFIG_CMD_MII=y
|
|
CONFIG_CMD_PING=y
|
|
CONFIG_CMD_CACHE=y
|
|
CONFIG_CMD_REGULATOR=y
|
|
CONFIG_CMD_EXT4=y
|
|
CONFIG_CMD_FS_GENERIC=y
|
|
CONFIG_CMD_MTDPARTS=y
|
|
CONFIG_DOS_PARTITION=y
|
|
CONFIG_OF_CONTROL=y
|
|
CONFIG_SPL_OF_CONTROL=y
|
|
CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent interrupts"
|
|
CONFIG_SPL_OF_PLATDATA=y
|
|
# CONFIG_SPL_OF_PLATDATA_PARENT is not set
|
|
CONFIG_ENV_OVERWRITE=y
|
|
CONFIG_ENV_IS_IN_SPI_FLASH=y
|
|
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
|
|
CONFIG_NET_RANDOM_ETHADDR=y
|
|
CONFIG_DM=y
|
|
CONFIG_SPL_DM=y
|
|
CONFIG_DEVRES=y
|
|
CONFIG_MXS_GPIO=y
|
|
CONFIG_SUPPORT_EMMC_BOOT=y
|
|
CONFIG_MMC_MXS=y
|
|
CONFIG_MTD=y
|
|
CONFIG_DM_MTD=y
|
|
CONFIG_DM_SPI_FLASH=y
|
|
CONFIG_SF_DEFAULT_BUS=3
|
|
CONFIG_SF_DEFAULT_SPEED=40000000
|
|
CONFIG_SPI_FLASH_SFDP_SUPPORT=y
|
|
CONFIG_SPI_FLASH_ISSI=y
|
|
CONFIG_SPI_FLASH_SPANSION=y
|
|
CONFIG_SPI_FLASH_STMICRO=y
|
|
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
|
|
CONFIG_SPI_FLASH_MTD=y
|
|
CONFIG_PHYLIB=y
|
|
CONFIG_PHY_ADDR_ENABLE=y
|
|
CONFIG_PHY_ADDR=1
|
|
CONFIG_PHY_FIXED=y
|
|
CONFIG_DM_ETH=y
|
|
CONFIG_FEC_MXC=y
|
|
CONFIG_MII=y
|
|
CONFIG_PINCTRL=y
|
|
CONFIG_PINCTRL_MXS=y
|
|
CONFIG_DM_REGULATOR=y
|
|
CONFIG_DM_REGULATOR_FIXED=y
|
|
CONFIG_DM_REGULATOR_GPIO=y
|
|
CONFIG_CONS_INDEX=0
|
|
CONFIG_SPI=y
|
|
CONFIG_DM_SPI=y
|
|
CONFIG_MXS_SPI=y
|
|
CONFIG_FS_FAT=y
|
|
# CONFIG_SPL_OF_LIBFDT is not set
|