bf904ea418
The "autoload" environment variable is always checked with env_get_yesno as it can be set to any form of no. The default behavior of env_get_yesno is to return -1 on variables that are not set, which acts as true in general (we test for non-zero return). To convert CONFIG_SYS_AUTOLOAD to Kconfig, given that it was almost always used to set autoload to no, first rename to CONFIG_SYS_DISABLE_AUTOLOAD for consistency sake. Then, make it so that if enabled we set autoload=0 in the default environment. Migrate all platforms which set CONFIG_SYS_AUTOLOAD to non-true or that set autoload to false in their default environment to using CONFIG_SYS_DISABLE_AUTOLOAD Signed-off-by: Tom Rini <trini@konsulko.com>
81 lines
1.9 KiB
Plaintext
81 lines
1.9 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_SKIP_LOWLEVEL_INIT=y
|
|
CONFIG_SYS_THUMB_BUILD=y
|
|
CONFIG_ARCH_VF610=y
|
|
CONFIG_SYS_TEXT_BASE=0x3f401000
|
|
CONFIG_SYS_MALLOC_LEN=0x202000
|
|
CONFIG_SYS_MALLOC_F_LEN=0x400
|
|
CONFIG_NR_DRAM_BANKS=1
|
|
CONFIG_ENV_SIZE=0x2000
|
|
CONFIG_ENV_OFFSET=0xA0000
|
|
CONFIG_DM_GPIO=y
|
|
CONFIG_DEFAULT_DEVICE_TREE="vf610-pcm052"
|
|
CONFIG_ENV_OFFSET_REDUND=0xC0000
|
|
CONFIG_TARGET_PCM052=y
|
|
CONFIG_SYS_LOAD_ADDR=0x82000000
|
|
CONFIG_SYS_MEMTEST_START=0x80010000
|
|
CONFIG_SYS_MEMTEST_END=0x87c00000
|
|
CONFIG_HAS_BOARD_SIZE_LIMIT=y
|
|
CONFIG_BOARD_SIZE_LIMIT=520192
|
|
CONFIG_BOOTDELAY=3
|
|
CONFIG_USE_BOOTCOMMAND=y
|
|
CONFIG_BOOTCOMMAND="run bootcmd_nand"
|
|
CONFIG_BOARD_EARLY_INIT_F=y
|
|
CONFIG_HUSH_PARSER=y
|
|
CONFIG_SYS_CBSIZE=256
|
|
CONFIG_SYS_PBSIZE=276
|
|
CONFIG_CMD_BOOTZ=y
|
|
CONFIG_CMD_MEMTEST=y
|
|
CONFIG_CMD_GPIO=y
|
|
CONFIG_CMD_I2C=y
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_NAND_TRIMFFS=y
|
|
CONFIG_CMD_DHCP=y
|
|
CONFIG_SYS_DISABLE_AUTOLOAD=y
|
|
CONFIG_CMD_MII=y
|
|
CONFIG_CMD_PING=y
|
|
CONFIG_CMD_FAT=y
|
|
CONFIG_MTDIDS_DEFAULT="nand0=NAND"
|
|
CONFIG_MTDPARTS_DEFAULT="mtdparts=NAND:640k(bootloader),128k(env1),128k(env2),128k(dtb),6144k(kernel),-(root)"
|
|
CONFIG_CMD_UBI=y
|
|
CONFIG_OF_CONTROL=y
|
|
CONFIG_ENV_OVERWRITE=y
|
|
CONFIG_ENV_IS_IN_NAND=y
|
|
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
|
|
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
|
CONFIG_DM=y
|
|
CONFIG_VYBRID_GPIO=y
|
|
CONFIG_DM_I2C=y
|
|
CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
|
|
CONFIG_I2C_DEFAULT_BUS_NUMBER=0x2
|
|
CONFIG_SYS_I2C_MXC=y
|
|
CONFIG_MISC=y
|
|
CONFIG_I2C_EEPROM=y
|
|
CONFIG_SYS_I2C_EEPROM_ADDR=0x50
|
|
CONFIG_FSL_ESDHC_IMX=y
|
|
CONFIG_MTD=y
|
|
CONFIG_DM_MTD=y
|
|
CONFIG_NAND_VF610_NFC=y
|
|
CONFIG_NAND_VF610_NFC_DT=y
|
|
CONFIG_SYS_NAND_ONFI_DETECTION=y
|
|
CONFIG_SYS_NAND_BUSWIDTH_16BIT=y
|
|
CONFIG_DM_SPI_FLASH=y
|
|
CONFIG_SPI_FLASH_STMICRO=y
|
|
CONFIG_SPI_FLASH_MTD=y
|
|
CONFIG_PHYLIB=y
|
|
CONFIG_PHY_MICREL=y
|
|
CONFIG_PHY_MICREL_KSZ8XXX=y
|
|
CONFIG_DM_ETH=y
|
|
CONFIG_FEC_MXC=y
|
|
CONFIG_MII=y
|
|
CONFIG_PINCTRL=y
|
|
CONFIG_PINCTRL_VYBRID=y
|
|
CONFIG_DM_RTC=y
|
|
CONFIG_RTC_M41T62=y
|
|
CONFIG_DM_SERIAL=y
|
|
CONFIG_FSL_LPUART=y
|
|
CONFIG_SPI=y
|
|
CONFIG_DM_SPI=y
|
|
CONFIG_FSL_QSPI=y
|
|
# CONFIG_EFI_LOADER is not set
|