a09fea1d28
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
70 lines
1.7 KiB
Plaintext
70 lines
1.7 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_ARCH_AT91=y
|
|
CONFIG_SYS_TEXT_BASE=0x26f00000
|
|
CONFIG_TARGET_AT91SAM9X5EK=y
|
|
CONFIG_SYS_MALLOC_F_LEN=0x2000
|
|
CONFIG_NR_DRAM_BANKS=1
|
|
CONFIG_DEBUG_UART_BOARD_INIT=y
|
|
CONFIG_DEBUG_UART_BASE=0xfffff200
|
|
CONFIG_DEBUG_UART_CLOCK=132000000
|
|
CONFIG_DEBUG_UART=y
|
|
CONFIG_FIT=y
|
|
CONFIG_NAND_BOOT=y
|
|
CONFIG_BOOTDELAY=3
|
|
CONFIG_USE_BOOTARGS=y
|
|
CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk mtdparts=atmel_nand:256k(bootstrap)ro,768k(uboot)ro,256k(env_redundant),256k(env),512k(dtb),6M(kernel)ro,-(rootfs) rootfstype=ubifs ubi.mtd=6 root=ubi0:rootfs rw"
|
|
# CONFIG_CONSOLE_MUX is not set
|
|
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
|
|
# CONFIG_DISPLAY_BOARDINFO is not set
|
|
CONFIG_HUSH_PARSER=y
|
|
CONFIG_SYS_PROMPT="U-Boot> "
|
|
CONFIG_CMD_BOOTZ=y
|
|
# CONFIG_CMD_FLASH is not set
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_NAND=y
|
|
CONFIG_CMD_NAND_TRIMFFS=y
|
|
CONFIG_CMD_USB=y
|
|
# CONFIG_CMD_SETEXPR is not set
|
|
CONFIG_CMD_DHCP=y
|
|
CONFIG_CMD_PING=y
|
|
CONFIG_CMD_FAT=y
|
|
CONFIG_CMD_MTDPARTS=y
|
|
CONFIG_CMD_UBI=y
|
|
CONFIG_OF_CONTROL=y
|
|
CONFIG_DEFAULT_DEVICE_TREE="at91sam9g35ek"
|
|
CONFIG_ENV_IS_IN_NAND=y
|
|
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
|
|
CONFIG_ENV_OFFSET_REDUND=0x100000
|
|
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
|
CONFIG_DM=y
|
|
CONFIG_CLK=y
|
|
CONFIG_CLK_AT91=y
|
|
CONFIG_DM_GPIO=y
|
|
CONFIG_AT91_GPIO=y
|
|
CONFIG_DM_MMC=y
|
|
CONFIG_GENERIC_ATMEL_MCI=y
|
|
# CONFIG_SYS_NAND_USE_FLASH_BBT is not set
|
|
CONFIG_NAND_ATMEL=y
|
|
CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER=y
|
|
CONFIG_DM_SPI_FLASH=y
|
|
CONFIG_SF_DEFAULT_SPEED=30000000
|
|
CONFIG_SPI_FLASH_ATMEL=y
|
|
CONFIG_DM_ETH=y
|
|
CONFIG_MACB=y
|
|
CONFIG_PINCTRL=y
|
|
CONFIG_PINCTRL_AT91=y
|
|
CONFIG_DM_SERIAL=y
|
|
CONFIG_DEBUG_UART_ATMEL=y
|
|
CONFIG_DEBUG_UART_ANNOUNCE=y
|
|
CONFIG_ATMEL_USART=y
|
|
CONFIG_SPI=y
|
|
CONFIG_DM_SPI=y
|
|
CONFIG_TIMER=y
|
|
CONFIG_ATMEL_PIT_TIMER=y
|
|
CONFIG_USB=y
|
|
CONFIG_DM_USB=y
|
|
CONFIG_USB_EHCI_HCD=y
|
|
CONFIG_USB_STORAGE=y
|
|
CONFIG_DM_VIDEO=y
|
|
CONFIG_ATMEL_HLCD=y
|