a09fea1d28
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
126 lines
3.3 KiB
C
126 lines
3.3 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Board configuration file for Variscite DART-6UL Evaluation Kit
|
|
* Copyright (C) 2019 Parthiban Nallathambi <parthitce@gmail.com>
|
|
*/
|
|
#ifndef __DART_6UL_H
|
|
#define __DART_6UL_H
|
|
|
|
#include <linux/sizes.h>
|
|
#include "mx6_common.h"
|
|
|
|
/* SPL options */
|
|
#include "imx6_spl.h"
|
|
|
|
/* NAND pin conflicts with usdhc2 */
|
|
#ifdef CONFIG_CMD_NAND
|
|
#define CONFIG_SYS_FSL_USDHC_NUM 1
|
|
#else
|
|
#define CONFIG_SYS_FSL_USDHC_NUM 2
|
|
#endif
|
|
|
|
#ifdef CONFIG_CMD_NET
|
|
#define CONFIG_FEC_ENET_DEV 0
|
|
|
|
#if (CONFIG_FEC_ENET_DEV == 0)
|
|
#define IMX_FEC_BASE ENET_BASE_ADDR
|
|
#define CONFIG_FEC_MXC_PHYADDR 0x1
|
|
#define CONFIG_FEC_XCV_TYPE RMII
|
|
#define CONFIG_ETHPRIME "eth0"
|
|
#elif (CONFIG_FEC_ENET_DEV == 1)
|
|
#define IMX_FEC_BASE ENET2_BASE_ADDR
|
|
#define CONFIG_FEC_MXC_PHYADDR 0x3
|
|
#define CONFIG_FEC_XCV_TYPE RMII
|
|
#define CONFIG_ETHPRIME "eth1"
|
|
#endif
|
|
#endif
|
|
|
|
/* Size of malloc() pool */
|
|
#define CONFIG_SYS_MALLOC_LEN (16 * SZ_1M)
|
|
|
|
/* Environment settings */
|
|
|
|
/* Environment in SD */
|
|
#define CONFIG_SYS_MMC_ENV_DEV 0
|
|
#define CONFIG_SYS_MMC_ENV_PART 0
|
|
#define MMC_ROOTFS_DEV 0
|
|
#define MMC_ROOTFS_PART 2
|
|
|
|
/* Console configs */
|
|
#define CONFIG_MXC_UART_BASE UART1_BASE
|
|
|
|
/* MMC Configs */
|
|
|
|
#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC2_BASE_ADDR
|
|
#define CONFIG_SUPPORT_EMMC_BOOT
|
|
|
|
/* I2C configs */
|
|
#ifdef CONFIG_CMD_I2C
|
|
#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
|
|
#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
|
|
#define CONFIG_SYS_I2C_SPEED 100000
|
|
#endif
|
|
|
|
/* Miscellaneous configurable options */
|
|
#define CONFIG_SYS_MEMTEST_START 0x80000000
|
|
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x8000000)
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
|
|
#define CONFIG_SYS_HZ 1000
|
|
|
|
/* Physical Memory Map */
|
|
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
|
|
#define PHYS_SDRAM_SIZE SZ_512M
|
|
|
|
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
|
|
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
|
|
#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
|
|
|
|
#define CONFIG_SYS_INIT_SP_OFFSET \
|
|
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_ADDR \
|
|
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
|
|
|
|
/* USB Configs */
|
|
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
|
|
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
|
|
#define CONFIG_MXC_USB_FLAGS 0
|
|
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
|
|
|
|
#define CONFIG_IMX_THERMAL
|
|
|
|
#define ENV_MMC \
|
|
"mmcdev=" __stringify(MMC_ROOTFS_DEV) "\0" \
|
|
"mmcpart=" __stringify(MMC_ROOTFS_PART) "\0" \
|
|
"fitpart=1\0" \
|
|
"bootdelay=3\0" \
|
|
"silent=1\0" \
|
|
"optargs=rw rootwait\0" \
|
|
"mmcautodetect=yes\0" \
|
|
"mmcrootfstype=ext4\0" \
|
|
"mmcfit_name=fitImage\0" \
|
|
"mmcloadfit=fatload mmc ${mmcdev}:${fitpart} ${fit_addr} " \
|
|
"${mmcfit_name}\0" \
|
|
"mmcargs=setenv bootargs " \
|
|
"root=/dev/mmcblk${mmcdev}p${mmcpart} ${optargs} " \
|
|
"console=${console} rootfstype=${mmcrootfstype}\0" \
|
|
"mmc_mmc_fit=run mmcloadfit;run mmcargs addcon; bootm ${fit_addr}\0" \
|
|
|
|
/* Default environment */
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"fdt_high=0xffffffff\0" \
|
|
"console=ttymxc0,115200n8\0" \
|
|
"addcon=setenv bootargs ${bootargs} console=${console},${baudrate}\0" \
|
|
"fit_addr=0x82000000\0" \
|
|
ENV_MMC
|
|
|
|
#define CONFIG_BOOTCOMMAND "run mmc_mmc_fit"
|
|
|
|
#define BOOT_TARGET_DEVICES(func) \
|
|
func(MMC, mmc, 0) \
|
|
func(MMC, mmc, 1) \
|
|
func(DHCP, dhcp, na)
|
|
|
|
#include <config_distro_bootcmd.h>
|
|
#endif /* __DART_6UL_H */
|