ad12dc1844
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:
../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {
Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
55 lines
1.3 KiB
Plaintext
55 lines
1.3 KiB
Plaintext
CONFIG_ARM=y
|
|
CONFIG_ARCH_AT91=y
|
|
CONFIG_TARGET_AT91SAM9260EK=y
|
|
CONFIG_SYS_MALLOC_F_LEN=0x2000
|
|
CONFIG_DEFAULT_DEVICE_TREE="at91sam9g20ek"
|
|
CONFIG_DEBUG_UART=y
|
|
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9G20,SYS_USE_DATAFLASH_CS0"
|
|
CONFIG_BOOTDELAY=3
|
|
CONFIG_USE_BOOTARGS=y
|
|
CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mtdblock0 mtdparts=atmel_nand:-(root) rw rootfstype=jffs2"
|
|
# CONFIG_DISPLAY_BOARDINFO is not set
|
|
CONFIG_SYS_PROMPT="U-Boot> "
|
|
# CONFIG_CMD_BDI is not set
|
|
CONFIG_CMD_BOOTZ=y
|
|
# CONFIG_CMD_IMI is not set
|
|
# CONFIG_CMD_FPGA is not set
|
|
# CONFIG_CMD_LOADS is not set
|
|
CONFIG_CMD_NAND=y
|
|
CONFIG_CMD_SF=y
|
|
CONFIG_CMD_USB=y
|
|
# CONFIG_CMD_SOURCE is not set
|
|
# CONFIG_CMD_SETEXPR is not set
|
|
CONFIG_CMD_DHCP=y
|
|
CONFIG_CMD_PING=y
|
|
CONFIG_CMD_FAT=y
|
|
CONFIG_OF_CONTROL=y
|
|
CONFIG_ENV_IS_IN_SPI_FLASH=y
|
|
CONFIG_DM=y
|
|
CONFIG_CLK=y
|
|
CONFIG_CLK_AT91=y
|
|
CONFIG_DM_GPIO=y
|
|
CONFIG_AT91_GPIO=y
|
|
# CONFIG_MMC is not set
|
|
CONFIG_DM_SPI_FLASH=y
|
|
CONFIG_SPI_FLASH=y
|
|
CONFIG_SPI_FLASH_ATMEL=y
|
|
CONFIG_SPI_FLASH_DATAFLASH=y
|
|
CONFIG_DM_ETH=y
|
|
CONFIG_MACB=y
|
|
CONFIG_PINCTRL=y
|
|
CONFIG_PINCTRL_AT91=y
|
|
CONFIG_DM_SERIAL=y
|
|
CONFIG_DEBUG_UART_ATMEL=y
|
|
CONFIG_DEBUG_UART_BASE=0xfffff200
|
|
CONFIG_DEBUG_UART_CLOCK=132000000
|
|
CONFIG_DEBUG_UART_BOARD_INIT=y
|
|
CONFIG_DEBUG_UART_ANNOUNCE=y
|
|
CONFIG_ATMEL_USART=y
|
|
CONFIG_DM_SPI=y
|
|
CONFIG_ATMEL_SPI=y
|
|
CONFIG_TIMER=y
|
|
CONFIG_ATMEL_PIT_TIMER=y
|
|
CONFIG_USB=y
|
|
CONFIG_USB_STORAGE=y
|